Double-tuned amplifier

A typical 2-stage double-tuned amplifier

The circuit shown consists of two stages of amplifier in common emitter topology. The bias resistors all serve their usual functions. The input of the first stage is coupled in the conventional way with a series capacitor to avoid affecting the bias. However, the collector load consists of a transformer which serves as the inter-stage coupling instead of capacitors. The windings of the transformer have inductance. Capacitors placed across the transformer windings form resonant circuits which provide the tuning of the amplifier.

A further detail that may be seen in this kind of amplifier is the presence of taps on the transformer windings. These are used for the input and output connections of the transformer rather than the top of the windings. This is done for impedance matching purposes; bipolar junction transistor amplifiers (the kind shown in the circuit) have a quite high output impedance and a quite low input impedance. This problem can be avoided by using MOSFETs which have a very high input impedance.[1]

The capacitors connected between the bottom of the transformer secondary windings and ground do not form part of the tuning. Rather, their purpose is to decouple the transistor bias resistors from the AC circuit.

Double tuning, as compared to single tuning, has the effect of widening the bandwidth of the amplifier and steepening the skirt of the response.[2] Tuning both sides of the transformer forms a pair of coupled resonators which is the source of the increased bandwidth. The gain of the amplifier is a function of the coupling coefficient, k, which is related to the mutual inductance, M, and the primary and secondary winding inductances, L_p and L_s respectively, by

${\displaystyle M=k{\sqrt {L_{\mathrm {p} }L_{\mathrm {s} }}}}$

There is a critical value of coupling at which the gain of the amplifier is a maximum at resonance. Below this critical value, there is a single peak in the frequency response with the amplitude peaking at resonance and the peak decreasing as k decreases. Such a response is said to be undercoupled, At values of k above critical coupling the response starts to split into two peaks. These peaks become narrower and further apart as k increases and the gap between them (centred on the resonant frequency) becomes progressively deeper. Such a response is said to be overcoupled.[3]

A critically coupled amplifier has a response that is maximally flat. This response can also be achieved without transformers with two stages of a stagger-tuned amplifier. Unlike staggered tuning, double tuning usually tunes both resonators to the same resonant frequency.[4] However, a designer might choose to design an overcoupled amplifier in order to achieve a wider bandwidth at the expense of a small dip (typically 3 dB to maximize the 3 dB bandwidth) in the centre of the frequency response.[5]

Like synchronous tuning, adding more stages of double-tuned amplifiers has the effect of reducing the bandwidth. The 3 dB bandwidth of n identical stages, as a fraction of the bandwidth of a single stage, is given approximately by,

${\displaystyle {\sqrt[{4}]{2^{1/n}-1}}}$

This expression applies only to small fractional bandwidths.[6]

The circuit can be represented in a more generic way by replacing the amplifiers with a generalised transconductance amplifier as shown.

Generic representation of one stage of a double-tuned amplifier and part of the following stage

where (omitting the stage number suffixes),

G_o is the output conductance of the amplifiers

G_i is the input conductance of the amplifiers.

Typically, a design will make the resonant frequencies and Qs on the primary and secondary sides identical, such that,

${\displaystyle \omega _{0}=\omega _{0\mathrm {p} }={1 \over {\sqrt {L_{\mathrm {p} }C_{\mathrm {p} }}}}=\omega _{0\mathrm {s} }={1 \over {\sqrt {L_{\mathrm {s} }C_{\mathrm {s} }}}}}$

and,

${\displaystyle Q=Q_{\mathrm {p} }={1 \over L_{\mathrm {p} }G_{\mathrm {o} }}=Q_{\mathrm {s} }={1 \over L_{\mathrm {s} }G_{\mathrm {i} }}}$

where ω₀ is the resonant frequency expressed in units of angular frequency and the subscripts p and s refer respectively to components on the primary and secondary side of the transformer.

Stage gain

Double-tuned amplifier frequency response for various values of coupling

With the above assumptions, the voltage gain, A of one stage of the amplifier can be expressed as

${\displaystyle A=A_{0}{\frac {2kQ}{4Q\delta -i(1+k^{2}Q^{2}-4Q^{2}\delta ^{2})}}}$

where

${\displaystyle i}$ is the imaginary unit,

${\displaystyle A_{0}={\frac {g_{\mathrm {m} }}{2{\sqrt {G_{\mathrm {o} }G_{\mathrm {i} }}}}}}$

is the maximum gain deliverable by the stage, and

${\displaystyle \delta ={\frac {\omega -\omega _{0}}{\omega _{0}}}}$

is the frequency expressed as the fractional frequency deviation from the resonant frequency.

• Bakshi, Uday A.; Godse, Atul P., Electronic Circuit Analysis, Technical Publications, 2009 ISBN 8184310471.
• Bhargava, N. N.; Gupta, S. C.; Kulshreshtha D. C., Basic Electronics and Linear Circuits, Tata McGraw-Hill, 1984 ISBN 0074519654.
• Chattopadhyay, D., Electronics: Fundamentals and Applications, New Age International, 2006 ISBN 8122417809.
• Gulati, R. R., Monochrome and Colour Television, New Age International, 2007 ISBN 8122416071.