Drop impact

• "Deposition" is said to occur when the drop spreads on the surface at impact and remains attached to the surface during the entire impact process without breaking up.[1] This outcome is representative of impact of small, low-velocity drops onto smooth wetting surfaces.
• The "prompt splash" outcome occurs when the drop strikes a rough surface, and is characterized by the generation of droplets at the contact line (where solid, gas, and liquid meet) at the beginning of the process of spreading of the drop on the surface, when the liquid has a high outward velocity.[1]
• At reduced surface tension, the liquid layer can detach from the wall, resulting in a "corona splash".[3]

Corona splash on a dry solid surface.

• On a wetting surface, "receding breakup" can occur as the liquid retracts from its maximum spreading radius, due to the fact that the contact angle decreases during retraction, causing some drops to be left behind by the receding drop.[1] On superhydrophobic surfaces, the retracting drop can break up into a number of fingers which are each capable of further breakup, likely due to capillary instability.[3] Such satellite droplets have been observed to break off from the impacting drop both during the spreading and retracting phases.[4]
• "Rebound" and "partial rebound" outcomes can occur when a drop recedes after impact. As the drop recedes to the impact point, the kinetic energy of the collapsing drop causes the liquid to squeeze upward, forming a vertical liquid column. The case where drop stays partially on the surface but launches one or more drops at its top is known as partial rebound, whereas the case where the entire drop leaves the solid surface due to this upward motion is known as complete rebound.[3] The difference between rebound and partial rebound is caused by the receding contact angle of the drop on the surface. For low values a partial rebound occurs, while for high values a complete rebound occurs (assuming that the drop recedes with enough kinetic energy).[1]

On superhydrophobic surfaces, liquid drops are observed to bounce off of the solid surface. Richard and Quéré showed that a small liquid drop was able to bounce off of a solid surface over 20 times before coming to rest.[5] Of particular interest is the length of time that the drop remains in contact with the solid surface. This is important in applications such as heat transfer and aircraft icing. To find a relationship between drop size and contact time for low Weber number impacts (We << 1) on superhydrophobic surfaces (which experience little deformation), a simple balance between inertia (${\displaystyle \rho R/\tau ^{2}}$) and capillarity (${\displaystyle \sigma /R^{2}}$) can be used,[6] as follows:

${\displaystyle \rho R/\tau ^{2}\propto \sigma /R^{2}}$

where ${\displaystyle \rho }$ is the drop density, R is the drop radius, ${\displaystyle \tau }$ is the characteristic time scale, and ${\displaystyle \sigma }$ is the drop surface tension.

This yields

${\displaystyle \tau \propto {\sqrt {\rho /\sigma }}R^{3/2}}$.

The contact time is independent of velocity in this regime. The minimum contact time for a low deformation drop (We << 1) is approximated by the lowest-order oscillation period for a spherical drop.,[7] giving the characteristic time a prefactor of approximately 2.2.[8] For large-deformation drops (We > 1), similar contact times are seen even though dynamics of impact are different, as discussed below.[8] If the droplet is split into multiple droplets, the contact time is reduced.[8]

Breakup of a water drop impacting a superhydrophobic surface at a Weber number of approximately 214.

By creating tapered surfaces with large spacing, the impacting droplet will exhibit the counterintuitive pancake bouncing, characterized by the droplet bouncing off at the end of spreading without retraction, resulting in ~80% contact time reduction.[9]

As the Weber number increases, the drop deformation upon impact also increases. The drop deformation pattern can be split up into regimes based on the Weber number.[6]

• At We << 1, there is not significant deformation.
• For We on the order of 1, the drop experiences significant deformation, and flattens somewhat on the surface.
• When We ~ 4, waves form on the drop.
• When We ~ 18, satellite droplet(s) break off of the drop, which is now an elongated vertical column.
• For large We (for which the magnitude depends on the specific surface structure), many satellite drops break off during spreading and/or retraction of the drop.[4]