Pilot plant

A pilot plant of a bioreactor

A pilot plant is a small industrial system, which is operated to generate information about the behavior of the system for use in design of larger facilities. Pilot plant is a relative term in the sense that plants are typically smaller than full-scale production plants, but are built in a range of sizes. Some pilot plants are built in laboratories using stock lab equipment, while others require substantial engineering efforts, cost millions of dollars, and are custom-assembled and fabricated from process equipment, instrumentation and piping. They can also be used to train personnel for a full-scale plant. Pilot plants tend to be smaller compared to demonstration plants.

Risk management

Pilot plants are used to reduce the risk associated with construction of large process plants. They do so in several ways:

If a system is well defined and the engineering parameters are known, pilot plants are not used. For instance, a business that wants to expand production capacity by building a new plant that does the same thing as an existing plant may choose to not use a pilot plant.

Additionally, advances in process simulation on computers have increased the confidence of process designers and reduced the need for pilot plants. However, they are still used as even state-of-the-art simulation cannot accurately predict the behavior of complex systems.

Design change

As a system increases in size, system properties that depend on quantity of matter (with extensive properties) might change. The chemical and physical properties of a system affect each other and create varying results. The surface area to liquid ratio is a good example of such a property. On a small chemical scale, in a flask, say, there is a relatively large surface area to liquid ratio. However, if the reaction in question is scaled up to fit in a 500-gallon tank, the surface area to liquid ratio becomes much smaller. As a result of this difference in surface area to liquid ratio, the exact nature of the thermodynamics and the reaction kinetics of the process changes in a non-linear fashion. This is why a reaction in a beaker can behave vastly differently from the same reaction in a large-scale production process.

Other factors

Other factors that change during the transformation to a production scale include:

After data is collected from operation of a pilot plant, a larger production-scale facility may be built. Alternatively, a demonstration plant, which is bigger than a pilot plant, but smaller than the full-scale production plant, may be built to demonstrate the commercial feasibility of the process. Businesses sometimes continue to operate the pilot plant in order to test ideas for new products, new feedstocks, or different operating conditions. Alternatively, they may be operated as production facilities, augmenting production from the main plant.

Recent trends try to keep the size of the plant a small as possible to save costs. This approach is called miniplant technology. The flow chemistry takes up this trend and uses flow miniplant technology for small-scale manufacturing.

Bench scale vs pilot vs demonstration

The differences between bench scale, pilot scale and demonstration scale are strongly influenced by industry and application. Some industries use pilot plant and demonstration plant interchangeably. Some pilot plants are built as portable modules that can easily transported as a contained unit.

For batch processes, in the pharmaceutical industry for example, bench scale is typically conducted on samples 1–20 kg or less, whereas pilot scale testing is performed with samples of 20–100 kg. Demonstration scale is essentially operating the equipment at full commercial feed rates over extended time periods to prove operational stability.

For continuous processes, in the petroleum industry for example, bench scale systems are typically microreactor or CSTR systems with less than 1000 cc of catalyst, studying reactions and/or separations on a once-through basis. Pilot plants will typically have reactors with catalyst volume between 1 and 100 litres filled with Jesse, and will often incorporate product separation and gas/liquid recycle with the goal of closing the mass balance. Demonstration plants, also referred to as semi-works plants, will study the viability of the process on a pre-commercial scale, with typical catalyst volumes in the 100 - 1000 litre range. The design of a demonstration scale plant for a continuous process will closely resemble that of the anticipated future commercial plant, albeit at a much lower throughput, and its goal is to study catalyst performance and operating lifetime over an extended period, while generating significant quantities of product for market testing.

In the development of new processes, the design and operation of the pilot and demonstration plant will often run in parallel with the design of the future commercial plant, and the results from pilot testing programs are key to optimizing the commercial plant flowsheet. It is common in cases where process technology has been successfully implemented that the savings at the commercial scale resulting from pilot testing will significantly outweigh the cost of the pilot plant itself.

Steps to creating a custom pilot plant

Custom pilot plants are commonly designed either for research or commercial purposes. They can range in size from a small system with no automation and low flow, to a highly automated system producing relatively large amounts of products in a day. No matter the size, the steps to designing and fabricating a working pilot plant are the same. They are:

  1. Pre-engineering - completing a process flow diagram (PFD), basic piping and instrumentation diagrams (P&ID's) and initial equipment layouts.
  2. Engineering modeling and optimization - 2D and 3D models are created, using a simulation software to model the process parameters and scale the chemical processes. These modeling softwares help determine system limitations, non-linear chemical and physical changes, and potential equipment sizing. Mass and energy balances, finalized P&ID's and general arrangement drawings are produced.
  3. Automation strategies for the system are developed (if needed). Controls system programming begins and will continue through fabrication and assembly
  4. Fabrication and assembly - after an optimized design has been determined, the custom pilot is fabricated and assembled. Pilot plants can either be assembled on-site or off-site as modular skids that will be constructed and tested in a controlled environment.
  5. Testing - testing of completed systems, including system controls, is conducted to ensure proper system function.
  6. Installation and startup - if constructed offsite, pilot skids are installed onsite. After all equipment is in place, full system startup is completed by integrating the system with existing plant utilities and controls. Full operation is tested and affirmed.
  7. Training - operator training is complete and full system documentation is handed over.

See also


Richard Palluzi, Pilot Plants: Design, Construction and Operation, McGraw-Hill, February, 1992. Richard Palluzi, Pilot Plants, Chemical Engineering, March, 1990.


    External links

    This article is issued from Wikipedia - version of the 10/19/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.