Steel detailer

A steel detailer prepares two primary types of drawings: erection drawings and shop drawings.

Erection drawings are used to guide the steel erector on the construction site ("in the field") as to where and how to erect the fabricated steel members. These drawings usually show dimensioned plans to locate the steel members, and they often also show details with specific information and requirements, including all work that must be done in the field (such as bolting, welding or installing wedge anchors). Since the erection drawings are intended for use in the field, they contain very little specific information about the fabrication of any individual steel member; members should already be completed by the time the erection drawings are used.

Shop drawings, also called detail drawings, are used to specify the exact detailing requirements for fabricating each individual member (or "piece") of a structure, and are used by the steel fabricator to fabricate these members. Complete shop drawings show material specifications, member sizes, all required dimensions, welding, bolting, surface preparation and painting requirements, and any other information required to describe each completed member. The shop drawings are intended for use by the fabrication shop, and thus contain little or no information about the erection and installation of the steel members they depict; this information belongs in the erection drawings.

The detailer must comply with the requirements of the design drawings and with all industry standards and protocols, such as those established by the American Institute of Steel Construction (AISC) and the American Welding Society (AWS). The detailer is usually not responsible for design, including structural strength, stiffness, and stability (which are the responsibility of the structural engineer), major dimensions of the structure and compliance with relevant building codes (which are the responsibility of the architect). A detailer is generally required to submit his drawings to the structural engineer and/or architect for review prior to the release of drawings for fabrication. However, to complete his drawings, an experienced steel detailer usually suggests connections subject to the approval of the structural engineer in cases where the structural drawings have insufficient information. In these situations, the steel detailer is guided by his experience and knowledge of existing engineering codes such as the Steel Construction Manual published by AISC.

In the case of non-building structures there is typically no architect, and detail drawings are reviewed exclusively by the structural engineer of record. This design review ideally assures engineering accuracy and compliance with the design intent.

Traditionally, steel detailing was accomplished via manual drafting methods, using pencils, paper, and drafting tools such as a parallel bar or drafting machine, triangles, templates of circles and other useful shapes, and mathematical tables, such as tables of logarithms and other useful calculational aids. Eventually, hand-held calculators were incorporated into the traditional practice.

Today, manual drafting has been largely replaced by computer-aided drafting (CAD). A steel detailer using computer-aided methods creates drawings on a computer, using software specifically designed for the purpose, and printing out drawings on paper only when they are complete. Many detailers would add another classification for those using 3-D Modeling applications specifically designed for steel detailing, as the process for the production of drawings using these applications is markedly different from a 2-D drafting approach. The detailer literally builds the project in 3D before producing detailed shop drawings from the model.

Structural steel detailing requires skills in drafting, mathematics (including geometry and trigonometry), logic, reasoning, spatial visualization, and communication. A basic knowledge of general engineering principles and the methods of structural and miscellaneous steel fabrication, however acquired, is essential to the practice of this discipline. A computer-aided detailer also requires skills in using computers and an understanding of the specific CAD software used.

A detailer's drawings generally go through several phases. If there is any unclear information that would prevent the detailer from creating or completing the drawings accurately, a request for information(RFI)[1] is sent to the relevant trades(typically the general contractor, architect or structural engineer) before proceeding. If the required information is not needed immediately, then the detailer may opt to list the questions on the drawings. Following creation of the drawing, the detailer must usually (as described above) submit a copy of the drawing to the architect and engineer for review ("approval"). Copies of the drawing may be sent to other recipients at this time as well, such as the general contractor, for informational purposes only. The drawing must also be checked for accuracy and completeness by another detailer (for this purpose, the "checker"). To keep track of changes during the drawing creation workflow, the revisions are identified by incrementing an associated number or letter code which should appear in the drawing revision block. Comments arising from approval and corrections made during checking must be resolved, and the original drawing must be updated accordingly (or "scrubbed"). After this, the drawing may be released to the fabricator and/or erector for use in construction.

• Drafter
• Modeler
• Model Checker
• Drawing Checker

• AISC
• Advance Steel Detailing Software Website
• Bentley ProSteel Detailing Software Website
• SDS/2 Structural Steel Detailing Software Website
• Soft Steel Detailing Software Website
• SSDCP Structural Steel Detailing Software Website
• Tekla Structures Steel Detailing Software Website
• Tekla Structures Interoperability and Formats
• The Steel Detailer software website
• Solidworks software website