Voltage divider

Figure 2: Simple resistive voltage divider

A resistive divider is the case where both impedances, Z₁ and Z₂, are purely resistive (Figure 2).

Substituting Z₁ = R₁ and Z₂ = R₂ into the previous expression gives:

${\displaystyle V_{\mathrm {out} }={\frac {R_{2}}{R_{1}+R_{2}}}\cdot V_{\mathrm {in} }}$

If R₁ = R₂ then

${\displaystyle V_{\mathrm {out} }={\frac {1}{2}}\cdot V_{\mathrm {in} }}$

If V_out = 6V and V_in = 9V (both commonly used voltages), then:

${\displaystyle {\frac {V_{\mathrm {out} }}{V_{\mathrm {in} }}}={\frac {R_{2}}{R_{1}+R_{2}}}={\frac {6}{9}}={\frac {2}{3}}}$

and by solving using algebra, R₂ must be twice the value of R₁.

To solve for R1:

${\displaystyle R_{1}={\frac {R_{2}\cdot V_{\mathrm {in} }}{V_{\mathrm {out} }}}-R_{2}=R_{2}\cdot \left({{\frac {V_{\mathrm {in} }}{V_{\mathrm {out} }}}-1}\right)}$

To solve for R2:

${\displaystyle R_{2}=R_{1}\cdot {\frac {1}{\left({{\frac {V_{\mathrm {in} }}{V_{\mathrm {out} }}}-1}\right)}}}$

Any ratio V_out/V_in greater than 1 is not possible. That is, using resistors alone it is not possible to either invert the voltage or increase V_out above V_in.

Figure 3: Resistor/capacitor voltage divider

Consider a divider consisting of a resistor and capacitor as shown in Figure 3.

Comparing with the general case, we see Z₁ = R and Z₂ is the impedance of the capacitor, given by

${\displaystyle Z_{2}=-\mathrm {j} X_{\mathrm {C} }={\frac {1}{\mathrm {j} \omega C}}\ ,}$

where X_C is the reactance of the capacitor, C is the capacitance of the capacitor, j is the imaginary unit, and ω (omega) is the radian frequency of the input voltage.

This divider will then have the voltage ratio:

${\displaystyle {\frac {V_{\mathrm {out} }}{V_{\mathrm {in} }}}={\frac {Z_{\mathrm {2} }}{Z_{\mathrm {1} }+Z_{\mathrm {2} }}}={\frac {\frac {1}{\mathrm {j} \omega C}}{{\frac {1}{\mathrm {j} \omega C}}+R}}={\frac {1}{1+\mathrm {j} \omega RC}}\ .}$

The product τ (tau) = RC is called the time constant of the circuit.

The ratio then depends on frequency, in this case decreasing as frequency increases. This circuit is, in fact, a basic (first-order) lowpass filter. The ratio contains an imaginary number, and actually contains both the amplitude and phase shift information of the filter. To extract just the amplitude ratio, calculate the magnitude of the ratio, that is:

${\displaystyle \left|{\frac {V_{\mathrm {out} }}{V_{\mathrm {in} }}}\right|={\frac {1}{\sqrt {1+(\omega RC)^{2}}}}\ .}$

Inductive dividers split AC input according to inductance:

${\displaystyle V_{\mathrm {out} }={\frac {L_{2}}{L_{1}+L_{2}}}\cdot V_{\mathrm {in} }}$

(with components in the same positions as Figure 2.)

The above equation is for non-interacting inductors; mutual inductance (as in an autotransformer) will alter the results.

Inductive dividers split DC input according to the resistance of the elements as for the resistive divider above.

Capacitive dividers do not pass DC input.

For an AC input a simple capacitive equation is:

${\displaystyle V_{\mathrm {out} }={\frac {C_{1}}{C_{1}+C_{2}}}\cdot V_{\mathrm {in} }}$

(with components in the same positions as Figure 2.)

Any leakage current in the capactive elements requires use of the generalized expression with two impedances. By selection of parallel R and C elements in the proper proportions, the same division ratio can be maintained over a useful range of frequencies. This is the principle applied in compensated oscilloscope probes to increase measurement bandwidth.

Voltage dividers can be used to allow a microcontroller to measure the resistance of a sensor.[1] The sensor is wired in series with a known resistance to form a voltage divider and a known voltage is applied across the divider. The microcontroller's analog-to-digital converter is connected to the center tap of the divider so that it can measure the tap voltage and, by using the measured voltage and the known resistance and voltage, compute the sensor resistance. An example that is commonly used involves a potentiometer (variable resistor) as one of the resistive elements. When the shaft of the potentiometer is rotated the resistance it produces either increases or decreases, the change in resistance corresponds to the angular change of the shaft. If coupled with a stable voltage reference, the output voltage can be fed into an analog-to-digital converter and a display can show the angle. Such circuits are commonly used in reading control knobs. Note that it is highly beneficial for the potentiometer to have a linear taper, as the microcontroller or other circuit reading the signal must otherwise correct for the non-linearity in its calculations.

High voltage (HV) resistor divider probe. The HV to be measured (V_IN) is applied to the corona ball probe tip and ground is connected to the other end of the divider via the black cable. The divider output (V_OUT) appears on the connector adjacent to the cable.

A voltage divider can be used to scale down a very high voltage so that it can be measured by a volt meter. The high voltage is applied across the divider, and the divider output—which outputs a lower voltage that is within the meter's input range—is measured by the meter. High voltage resistor divider probes designed specifically for this purpose can be used to measure voltages up to 100 kV. Special high-voltage resistors are used in such probes as they must be able to tolerate high input voltages and, to produce accurate results, must have matched temperature coefficients and very low voltage coefficients. Capacitive divider probes are typically used for voltages above 100 kV, as the heat caused by power losses in resistor divider probes at such high voltages could be excessive.

A voltage divider can be used as a crude logic level shifter to interface two circuits that use different operating voltages. For example, some logic circuits operate at 5V whereas others operate at 3.3V. Directly interfacing a 5V logic output to a 3.3V input may cause permanent damage to the 3.3V circuit. In this case, a voltage divider with an output ratio of 3.3/5 might be used to reduce the 5V signal to 3.3V, to allow the circuits to interoperate without damaging the 3.3V circuit. For this to be feasible, the 5V source impedance and 3.3V input impedance must be negligible, or they must be constant and the divider resistor values must account for their impedances. If the input impedance is capacitive, a purely resistive divider will limit the data rate. This can be roughly overcome by adding a capacitor in series with the top resistor, to make both legs of the divider capacitive as well as resistive.