Wheel hub motor

The Lohner-Porsche Mixte Hybrid, the world's first gasoline-electric hybrid automobile, used wheel hub motors.[1][2]

• First wheel motor concept: Wellington Adams of St. Louis first conceived of building an electric motor directly in the vehicle wheel, though it was attached via complicated gearing. The Adams patent is U.S. Patent 300,827in 1884.
• High torque low RPM wheel motor invented: The motor was incorporated into the wheel without gearing and addressed torque considerations through the use of a new high torque, low rpm motor invented by Edward Parkhurst of Woburn, MA in U.S. Patent 422,149 in 1890 (and mismentioned in Parcelle's patent as #320,699).
• Electric wheel motor advantages revealed in patent: An early wheel hub electric motor was invented by Frenchman Charles Theryc and patented in 1896 as U.S. Patent 572,036 entitled Wheel with Electric Motor hub for Vehicles. In the patent he explained all advantages including no transmission losses because of the absence of classic transmission rods from engines to wheels.
• Diesel wheel motor: Not all wheel hub motors were electric. C F Goddard in 1896 invented a piston hub motor for horseless carriages patented in U.S. Patent 574,200. He envisioned it powered by expanding gas of some kind. His offcenter flexible bent spoke designs later appeared in the Apollo moon rovers' wheels in 1960s.
• Using cams, another type of combustion wheel motor: In U.S. Patent 593,248 W C Smith in 1897 developed another explosive gas expansion motor inside a wheel hub that utilized cams on a track in the hub to transmit power to the wheel.

The electric wheel hub motor was raced by Ferdinand Porsche in 1897 in Vienna, Austria. Porsche's first engineering training was electrical, not internal combustion based. As a result, he developed his first cars as electric cars with electric wheel hub motors that ran on batteries. The Lohner Porsche, fitted with one wheel motor in each of the front wheels, appeared at the World Exhibition in Paris in 1900 and created a sensation in the young automobile world. In the following years, 300 Lohner Porsches were made and sold to wealthy buyers.[3]

Eventually the growth in power of the gasoline engine overtook the power of the electric wheel hub motors and this made up for any losses through a transmission. As a result, autos moved to gasoline engines with transmissions, but they were never as efficient as electric wheel hub motors. A potential exception to this history occurred on 17 January 2012 with the granting of U.S. Patent 8,096,103, The General Wheel Rotation Power Motor, a pressure driven three cylinder wheel motor contained in the hub that applies this force through crank wheels directly to the rotating rim surrounding the hub.[4]

• They are commonly found on electric bicycles and motorcycles.[5]
• Wheel motors are applied in industry, e.g. driving wheels that are part of assembly lines.
• Tyre makers and component producers have developed them[6] and the first production car to use them was the Luka EV by MW Motors.[7]
• Hub motors can also be found on buses.[8]

As of 2020, at least three companies are planning to release production vehicles with wheel hub motors in 2021:

• Aptera Motors has announced the highly efficient Aptera EV, a solar powered, enclosed three wheeler using hub motors from the company, Elaphe.[9]
• Lightyear has announced a solar powered automobile using hub motors, the Lightyear One.[10]
• Lordstown Motors has announced 4 wheel drive prickup truck, the Lordstown Endurance, with motors from Elaphe.[9]

Concept cars

PML Mini QED electric vehicle

MAZ-7907 truck. Each wheel has its own electric motor.

Several concept cars have been developed using in-wheel motors:

• General Motors Sequel 2005
• Protean Electric's Mini QED in 2006, Ford F-150 pickup truck in 2008,[11] and other cars using its Hi-Pa Drive
• Mitsubishi MIEV concept model in 2005
• Chebela (2010), a small urban EV prototype using 2 direct-drive in-wheel motors in the rear.
• Citroën C-Métisse with in wheel electric motors developed by TM4.[12]
• Siemens VDO (bought by Continental) eCorner concept in 2006[13][14]
• Heuliez WILL using the Michelin Active Wheel (which incorporates motorized active suspension as well) in 2008[15]
• The ZAP-X in 2007 "would use high-tech electric hub motors at all four wheels, delivering 644 horsepower to the ground from a lithium-ion battery pack. The hub motors would eliminate the need for transmission, axles and conventional brakes, opening up space beneath the floor for a giant battery pack."[16]
• The Peugeot BB1 in 2009 incorporates rear in-wheel motors designed with Michelin.[17]
• The Hiriko folding urban electric prototype has the drive motors located inside each of the four wheels, and has an electronically controlled maximum speed of 50 km/h (31 mph).[18][19] Each wheel integrates a motor, steering actuators, suspension and braking right inside the wheel, controlled by a drive-by-wire system.[20]
• In 2019 Israeli startup REE announced its Corner Module that combines motor, braking, suspension, software, and by-wire steering, and envisioned using four of these modules in delivery vehicles and small vans.[21] Toyota subsidiary Hino Motors showed a concept 6x6 truck chassis named "FlatFormer" using similar technology at the 2019 Tokyo Motor Show.[22]

Hub motor electromagnetic fields are supplied to the stationary windings of the motor. The outer part of the motor follows, or tries to follow, those fields, turning the attached wheel. In a brushed motor, energy is transferred by brushes contacting the rotating shaft of the motor. Energy is transferred in a brushless motor electronically, eliminating physical contact between stationary and moving parts. Although brushless motor technology is more expensive, most are more efficient and longer-lasting than brushed motor systems.

A hub motor typically is designed in one of three configurations. Considered least practical is an axial-flux motor, where the stator windings are typically sandwiched between sets of magnets. The other two configurations are both radial designs with the motor magnets bonded to the rotor; in one, the inner rotation motor, the rotor sits inside the stator, as in a conventional motor. In the other, the outer-rotation motor, the rotor sits outside the stator and rotates around it. The application of hub motors in vehicular uses is still evolving, and neither configuration has become standard.[23]

Electric motors have their greatest torque at startup, making them ideal for vehicles as they need the most torque at startup too. The idea of "revving up" so common with internal combustion engines is unnecessary with electric motors. Their greatest torque occurs as the rotor first begins to turn, which is why electric motors do not require a transmission. A gear-down arrangement may be needed, but unlike in a transmission normally paired with a combustion engine, no shifting is needed for electric motors.[24]

Wheel hub motors are increasingly common on electric bikes and electric scooters in some parts of the world, especially Asia.[25][26]

Compared with the conventional electric vehicle design with one motor situated centrally driving two (sometimes four) wheels by an axle or driveshaft,[27] the in-wheel motor arrangement has certain advantages and disadvantages:

Drive by wire

The Hiriko Fold pre-production model uses a hub wheel that integrates a motor, steering actuators, suspension and braking right inside the wheel, controlled by a drive-by-wire system.

Cars with electronic control of brakes and acceleration for each individual wheel provide more opportunities for computerized vehicle dynamics such as:

• Brake steer, where individual wheel brake bias is adjusted to assist steering (similar to a tracked vehicle like a bulldozer)[28]
• Active software differentials, where individual wheel speed is adjusted in response to other inputs
• Active brake bias, where individual wheel brake effort is adjusted in real-time to maintain vehicle stability

However, these benefits also accrue to vehicles with an in-board motor for each wheel. Wheel assemblies with in-wheel motors can pivot through greater angles than a conventional steering rack allows, and the Protean and REE "corner modules" add steering motors that allow vehicle motion in any direction, called crab steering.[29]

As wheel motors brake and accelerate a vehicle with a single solid-state electric/electronic system many of the above features can be added as software upgrades rather than requiring additional systems/hardware to be installed. This should lead to cheaper active dynamic safety systems for road vehicles equipped with wheel motors.

• ActiveWheel
• Locking hubs
• Direct drive mechanism

Wikimedia Commons has media related to In-wheel motors.

• e-Traction in-wheel direct drive technology
• Mitsubishi' experimental car, presented in May 2005, is fitted with wheel motors at the rear.
• The ez-Wheel
• Elaphe performance in-wheel electric motors