2-10-10-2

ATSF 3000 class
ATSF 3000 class 2-10-10-2. The forward section of the boiler is actually a primitive superheater and feedwater heater
Type and origin Power type Steam Builder ATSF Build date 1911-1912 Rebuilder Baldwin Locomotive Works and ATSF Rebuild date 1915-1918 (as 2-10-2’s) Number rebuilt 10
Specifications Driver dia. 57 in (1.448 m) Wheelbase 108 ft 10 in (33.17 m) Length 122 ft (37.19 m) Loco weight 616,000 lb (279,400 kg; 279.4 t) Tender weight 266,400 lb (120,800 kg; 120.8 t) Boiler pressure 225 psi (1.55 MPa) Cylinders Four, compound, HP rear, LP front High-pressure cylinder 28 in × 32 in (711 mm × 813 mm) Low-pressure cylinder 38 in × 32 in (965 mm × 813 mm)
Performance figures Tractive effort 111,600 lbf (496 kN)
Career Operators Atchison, Topeka and Santa Fe Railway Numbers 3000–3009 Retired 1945-1953 Preserved 0 Scrapped 1947-1953 Disposition All scrapped

This class of ten 2-10-10-2 locomotives were actually rebuilt from more conventional 2-10-2 Baldwin-built locomotives by the Atchison, Topeka and Santa Fe Railway in 1911 to 1912.

Although they appeared to have exceedingly long boilers, the barrel in front of the rear set of cylinders actually contained first a primitive firetube superheater for further heating the steam before use; the steam was carried forward from the boiler proper by outside steam pipes as shown in the photograph. Also in this space was a reheater for the high-pressure exhaust before it was fed to the forward low-pressure cylinders.

In front of that, there was a feedwater heater, a space where cold water from the tender could be warmed before being injected into the water proper. This worked similarly to the boiler itself; the firetubes passed through the feedwater tank. The ATSF 2-10-10-2's, #3000 class locomotives, were the largest locomotives in the world from 1911 till possibly early 1914.

Despite being good for helper service, they could only go 10 to 15mph before losing steam, resulting in the locomotives being rebuilt to 2-10-2s during 1915–1918.

Virginian Class AE
Virginian Class AE
Type and origin Reference:[1] Power type Steam Builder American Locomotive Company Build date 1918 Total produced 10
Specifications Configuration: ​  • Whyte 2-10-10-2 Gauge 4 ft 8 1⁄2 in (1,435 mm) Driver dia. 56 in (1,422 mm) Wheelbase 64.25 ft (19.58 m) Width 12.0 ft (3.658 m) Height 16.7 ft (5.090 m) Adhesive weight 617,000 lb (279,866 kg; 280 t) Loco weight 684,000 lb (310,257 kg; 310 t) Tender weight 231,000 lb (104,780 kg; 105 t) Total weight 915,000 lb (415,037 kg; 415 t) Fuel type Coal Water cap 13,000 US gal (10,825 imp gal; 49,210 L) Tender cap. 12 short tons (10.7 long tons; 10.9 t) Firebox:  • Firegrate area 109 sq ft (10 m2) Boiler 119 in (3,023 mm) Boiler pressure 215 psi (1 MPa) Heating surface 8,606 sq ft (800 m2) Superheater: ​  • Heating area 2,120 sq ft (197 m2) Cylinders Four, compound, LP front, hp rear High-pressure cylinder 30 in × 32 in (762 mm × 813 mm) Low-pressure cylinder 48 in × 32 in (1,219 mm × 813 mm) Loco brake Air Train brakes Air
Performance figures Tractive effort Compound: 147,200 lbf (655 kN) Simple: 175,000 lbf (778 kN) Factor of adh. 4.2
Career Operators Virginian Number in class 10 Numbers 800-809 Disposition All scrapped from 1943-1945,1947-1949

These ten locomotives were built in 1918 by ALCO for the Virginian Railway. Overall width was 144 inches (3,658 mm), so they were delivered without their cabs and the front, low-pressure cylinders and were assembled after arrival. The 48-inch (1,219 mm) low-pressure cylinders (on 90-inch or 2,286-millimetre centers) were the largest on any US locomotive; the cylinders had to be inclined a few degrees to provide clearance.[1] The boiler was also the largest diameter of any locomotive; Railway Mech Engnr says "the outside diameter of the largest course is 112 ⁷⁄₈ inches (2,867 mm)." but the drawing shows 118 ¹⁄₂ inches (3,010 mm) diameter at the rear tube sheet.

As seen in the photograph, the tenders were small so they could use the Virginian's existing turntables.

This class were compound Mallet locomotives: as well as being articulated between the forward, swinging engine unit and the rear fixed one, they were compound locomotives. The rear, high-pressure cylinders exhausted their steam into the huge front cylinders. Like many compound locomotives, they could be operated in simple mode for starting; reduced-pressure steam could be sent straight from the boiler to the front cylinders at low speed, for maximum tractive effort.

Calculated in the usual way the tractive effort was 147,200 lb (66,800 kg) in compound; or 176,600 lb (80,100 kg) in simple for the Virginian locomotives.[2]

Unlike some other giant locomotives of the period, the immense boilers could generate enough steam to make them a success on the slow (8 mph or 13 km/h) coal trains for which they were built. They remained in service until the 1940s and could be called the ultimate drag era locomotive. No locomotive example of this type survived into preservation.[1]