Cairns Wharf Complex

Replacement of the timber wharves with concrete ones proceeded progressively starting in about 1910. This commenced with the manufacture of 67 concrete piles and foundation dredging. Plans were for each section of the wharf to be 300 feet (91 m) long by 90 feet (27 m) wide with a shed 240 feet (73 m) long by 60 feet (18 m) wide built directly onto each wharf. Reclamation was to take place behind the sea wall at the back of the wharf with mud from the dredge stiffened with the stone and mullock from the range railway after slips took place. The number 3 wharf was erected by 1912, number two wharf opened in 1913, and in 1914 the old number 4 wharf and buildings were demolished and replaced with a concrete wharf.[1]

A photograph is available of the number 4 wharf during this reconstruction phase. The piles are reinforced concrete and the upper ends were apparently poured in-place in stages around four vertical iron rods. The iron reinforcing rods in the vertical posts were designed to interlock with the reinforcing rods in the concrete deck supports. Eight piles were placed between the sea wall area and the seaward edge of the wharf. Substantial wooden formwork was necessary to construct the reinforced concrete superstructure to support the decking.[1]

The Harbour Board purchased the timber number 1 wharf in 1915, and replaced this with a concrete wharf within a year. The number 5 wharf was constructed in 1925 and was the entry/exit point for railway lines extending onto the wharf deck. Plans indicate that the number 5 wharf's deck had two pairs of railway tracks which merged at the junction with the number 4 wharf. The tracks curved onto the wharf deck at the southern end of the number 5 wharf, and the corner of the wharf was truncated parallel to this curve.[1]

Number 6 wharf was completed in 1942 by the Allied Works Council. The design employed in constructing this wharf differed markedly to that used to construct numbers 1 to 5.: number 6 wharf was built with timber, supplemented with reinforced concrete.[1]

The Wharf Sheds were constructed at various stages throughout the first half of the twentieth century.[1]

The first to be built were numbers 2 and 3 wharf cargo sheds, constructed on the decks of the concrete wharves. The number 3 wharf was constructed in 1912, and it is suspected that the number 3 wharf shed was constructed in late 1912 or early 1913. The number 2 wharf was constructed in 1912-1913, and the original sheds on the old timber wharf were retained as long as possible prior to being demolished in 1913. The number 2 wharf shed was constructed soon after this demolition. The numbers 2 and 3 sheds were connected by a continuous roof by 1925 and probably earlier. Much of the infrastructure related to the number 2 and 3 sheds was constructed in about 1913, including the nearby railway tracks and two 10-ton cranes adjacent to the tracks and immediately behind sheds 1 and 2. Loading platforms were constructed behind number 2 wharf shed by 1925. The wharf sheds were elevated above the surrounding dock land and wharves. This raised configuration of wharf sheds was considered to be state-of-the-art design which allowed easy loading and unloading of goods to and from railway cars and into the storage sheds (facilitated by wharf shed platforms that aligned to the height of the rail cars). An "awning" was installed to the rear of the number 2 wharf shed in 1942. The wharf shed roofs were cleaned and repainted in 1947, and the whole of the roof cladding was replaced in 1954. The northern end of the number 2 wharf shed is referred to as the "old engine room" on a 1978 plan.[1]

A clock tower was added to the end of the number 3 wharf shed in 1947-1948. On 14 September 1948, the Cairns Post included the following details of the clock:[1]

The four dials are each six feet in diameter and are driven by a single central unit. They cannot show a different time on each face.[1]

The bell weighs half a ton, is three feet in diameter and is struck by a 20 pound hammer.[1]

The clock is operated electrically, but does not depend on the continuity of the mains. Timekeeping is kept by a pendulum weighing 100 lbs., which pushes the mechanism round with a force capable of overcoming all normal obstacles, yet it is so delicately powered that it takes only a fraction of the current an ordinary electric torch would consume.[1]

The only part of the clock which would stop if electricity failed would be the bell, operated by a one quarter horse power motor directly connected to the mains. As soon as current is restored it will pick up the correct hour automatically. It is intended to silence the chimes between mid-night and 5.30 a.m.[1]

There are 27 gear wheels in the clock and about 30 bal bearings, which are heavy enough for hundreds of years of wear.[1]

Mr Franklin says that the clock is similar to that designed and installed by him for the Townsville Harbour Board in 1940 and others he has constructed during the last 25 years, though each successive clock has incorporated some refinement in design.[1]

Throughout the interwar years, a shed was built for each of the other berths. The sheds at berths 1-3 were joined together in one continuous line; and sheds 4-5 were built as one long structure. In 1943, shed number 6 was constructed.[1]

In more recent times, viewing platforms were installed above the original roof line of number 2 wharf shed. The platforms were used as part of the terminal facilities for overseas passengers. These platforms were removed sometime in 1998 or 1999.[1]

In 1984, number 1 wharf shed was demolished as part of the Trinity Wharf development, and in the 1990s number 4 wharf shed was demolished to provide greater wharf space. Wharf sheds 5 and 6 have also been demolished.[1]

The sugar storage shed was constructed in 1923. An electrical conveyor system was installed in the shed to move sugar bags to and from ships' holds and railway wagons, and was fully operational by 1926. The system consisted of an inclined covered conveyor extending from railway tracks on the west side of the shed up to the shed's roofline. This conveyor provided the linkage with the wharf railway system. A complicated set of conveyors and chutes was built into the roof of the sugar shed, and this system was used to stack bagged sugar at a rate of up to 80 long tons (81 t) per hour. A second conveyor extended between the roof of the sugar shed eastwards to the roof of number 4 wharf shed. This conveyor joined another in a T-configuration on the eastern side of the wharf shed's roof. The overhead conveyors from White's Shed to number 3 wharf were reconstructed in 1946, while maintenance and repairs to both "shore and floating plant" were made in 1947. The 27-year-old facility was apparently modernised during the overhaul. Two travelling gantry cranes moved up and down the number 4 wharf's edge, loading and unloading the sugar bags into ship's holds via a set of conveyors mounted on the gantry cranes and connected to the T-conveyor.[1]

Electric travelling cranes were located immediately adjacent to the northern end and western side of the building during this era. These cranes moved "sinker" logs from the railway tracks to the edge of the wharf between the numbers 3 and 4 wharf sheds.[1]

The usefulness of the shed and log handling machinery declined in the late 1950s, and White's Shed was no longer in operation after the bulk sugar terminal was established at Portsmith in 1964. At this new terminal, huge volumes of sugar could be stored and delivered directly into the holds of ships, without needing to be packed into bags or other containers. This new method of sugar handling reduced significantly the wharf labour force for sugar. The sinker log crane on the west side of the shed was sold in 1959 and was later used at Rankine's Peeramon Mill, near Lake Eacham on the Atherton Tablelands, where it currently resides. The disused White's Shed was subsequently leased to mining companies, perhaps as early as the 1960s. The shed was used to store copper concentrate from the Red Dome mine between 1993 and 1997, and was leased to the Dianne Copper Mine prior to this. The name "White's Shed" derives from this period.[1]

The existing electrical workshop building is situated in the former location of the harbour workshops. The original workshops contained the fitter's and turner's shop and the blacksmith shop. This building was apparently demolished in about 1940, and the existing brick structure was built in this location in 1951. The rear shed was built and/or modified in 1967.[1]

The existing building was used to supply power to the wharves, and as an electrical workshop. During its years as a powerhouse, the building contained a compressor, an emergency power generator, and transformers. A compressor was installed in 1955 to supply air to the wharves, and it was in this year that electrical workshop equipment was installed. The workshop maintained 21 cranes, fork lifts, and two stevedoring units. The workshop was still in use by 1958 and possibly later.[1]

The Amenities Hall was built in 1954 for the Waterside Workers' Federation. The rear structure addition is possibly a "septic block" installed in 1956. The 1954 plan of the building shows the arrangement of the amenities, with the front two-thirds of the building filled with tables and the rear containing the amenities themselves.[1]

The building has housed collections of the Maritime Archaeological Association of Far North Queensland since 1988. A loading door is present in the front end of the building, and was reportedly added after 1988 so that large maritime artefacts could be easily moved into the structure.[1]

A 1942 map of the wharf complex shows four traffic gates to the wharf complex fronting Wharf Street. It is suspected that these gateways were in place since the early history of the wharves. The number 2 gateposts at the number 2 gate are still in their original locations.[1]

An octagonal three-tiered flagpole base was present at the eastern end of the existing garden bed. The flagpole base was concrete, and each tier was of decreasing diameter and height. The edge was bevelled. The base measured 1.2 metres (3 ft 11 in) across and 0.3 metres (1 ft 0 in) high, and the flagpole was once affixed by four bolts. This base was removed during maintenance activities in March 1999. Another flagpole base was constructed in July 1953.[1]

Concrete roadways were constructed on the reclaimed land behind numbers 1, 2 and 3 wharves in 1945 and 1946. The roads constructed in 1945 extended behind the wharves from number 1 to number 6 and the remainder of the concrete roads were presumably constructed in 1946.[1]

The Cairns Harbour Board Store (no longer extant) is clearly visible in 1920-1930 and 1940 aerial photographs of the area. The building was originally a bond store used by Customs to house beer, alcohol, and tobacco. The floor reportedly had a steel floor during this period to prevent theft. In recent years the building housed Coxen Chemicals (a detergent manufacturer) and Rothfire Pty Ltd (a prawn merchant). The building was either moved in the last decade to the modern workshop area or was demolished to make way for the bitumen carpark.[1]

Several railway tracks were laid at the Cairns wharves. The existing railway lines were laid at approximately the same time as the concrete wharves. One section of the line supported a 10-ton travelling crane, and another section, a travelling crane used to sort and load logs onto the parallel railway tracks.[1]

Rail links with the Cairns hinterland were a key element of the success of Cairns as the regional port and consequently, as a viable town.[1]

The park north of the Amenities Hall was once the location of several small structures. A 1942 plan of the area indicates that the "Pay Office" and a "Kiosk", both built in c. 1930 were present in the park area at that time. A "Tally Clerk's" office, built in c. 1930 was adjacent to the railway line behind the wharves. These buildings were apparently replaced by two small sheds prior to 1967, and the small sheds were themselves removed between 1972 and 1975.[1]

The concrete wharves are part of the actively utilised wharf facilities in this part of the Cairns waterfront.[1]

The wharf is decked in reinforced concrete which forms an integral part of the structure. The deck edge is marked by a discontinuous wooden beam. A series of concrete sections measuring about 3 metres (9.8 ft) long are immediately adjacent to the beam and extend the length of the wharf. The concrete sections are interrupted at regular intervals by metal boxes containing power points. Water taps are present at regular intervals, and plumbing, electrical conduits, and compressed air pipes are affixed to the underside of the wharf. Mooring irons are mounted to the deck surface behind the concrete buffers. A variety of types of mooring irons are present.[1]

Sheds 2 and 3 with clock tower, 1997

The number 2 and 3 wharf sheds are long, rectangular buildings, clad with corrugated sheeting. The structures have truss-framed roofs with support posts along the long edges and down the centre. The walls have timber rails spanning between the posts and numerous door and window openings within the framing. Like the walls, the roofs are clad with corrugated sheeting. Aside from clearly modern replacement sections, the wall cladding - much of which is affixed with lead-head nails of various sizes - appears to be the original.[1]

The buildings are in good condition, particularly given their age, location. exposure and past industrial usage. However the framing at the southern end of number 3 wharf shed exhibits signs of accelerated deterioration due to exposure to the weather. The covered area between the number 2 and number 3 wharf sheds appears to remain in a condition similar to that when it was originally constructed.[1]

The loading dock behind number 2 wharf shed is largely intact and consists of an array of heavily maintained timber and concrete piles supporting a concrete deck. It is aligned perpendicular to the railway tracks. The loading dock remnant existing behind number 3 wharf shed consists of rectangular, round, or half-round decking support timbers placed on log or concrete piers. This loading dock also has a concrete deck.[1]

The southern end of the wharf shed number 3 is surmounted by a clock tower. A clock face is located on all four sides of the tower. The tower is capped with a pyramidal roof and weather vane. A door providing internal access to the clock is located on the northern wall of the tower. Vents are located on all sides of the tower, close to the base. The clock appears to be in good working order and still chimes on the hour.[1]

The number 2 wharf shed is currently used as the Cairns cruise ship terminal. Number 3 wharf shed contains storage areas for the Port Authority, storage for other shipping operators, and offices for the Customs Service.[1]

The cargo crane is present at the end of the loading dock attached to the rear of number 2 wharf shed. The crane is mounted on a large 12-sided concrete base. The crane's I-beam jibs are stamped "NORMAN LONG AND CO LD/MIDDLESBROUGH/ENGLAND". The hoist consists of a cargo hook suspended by a steel cable. The cable winding drum is timber and largely intact. A commemorative bronze plaque is installed at the base of the crane.[1]

White's Shed is a large timber-and-iron structure situated behind number 4 wharf (not included in the listing boundary) and immediately southwest of the existing number 3 wharf shed. The building consists of the original section measuring approximately 63 metres (207 ft) long (oriented parallel to the wharf) and 22 metres (72 ft) wide, and the post-1976 addition. The cladding on the two sections overlap somewhat, and the complete width of the existing shed is about 38 metres (125 ft). A fence encloses the immediate surrounds to the northern side of the shed.[1]

The basic structure of White's Shed appear to be largely intact, including much of the sugar bag stacking apparatus on the ceiling. However, the portions of the sugar conveyor located outside of the shed are no longer extant.[1]

White's Shed is timber framed. Thirteen transverse frames support the roof, which are in turn linked by a ridge beam, purlins and girts, a wall top plate, and diagonal wall braces. Large double doors are present in the ends of the building and central on the east and west walls. These doors are supported by I-beams. The roof is gabled and has a ventilated ridge. A complex system of conveyors and hopper chutes for the delivery of sugar bags is present attached to the ceiling of the structure. The building's wall and roof cladding is of recently installed corrugated sheeting. A secure room is present along the inside of the north wall.[1]

A recent building report and contamination assessment revealed that the structural integrity of the building has been compromised by termites, and that a low level of heavy metals contamination is present.[1]

The Electrical workshop consists of a brick structure located immediately north of White's Shed. The building measures approximately 20 metres (66 ft) long and 12 metres (39 ft) wide, and has an 8 by 4 metres (26 by 13 ft) shed in the rear (west) yard. The building is currently the Cairns Port Authority's Social Club.[1]

The building's walls are cavity brick. The structure was constructed on a concrete slab and covered by a gabled roof. Five 4-paned windows extend down the northern side of the building. The windows are constructed with concrete lintels and sills. Four windows extend down the eastern end. A boarded-over attic window is also present. The south side of the building is marked by loading doors and four windows and this area is landscaped and modified for social functions. The western end of the building is marked by large access doors, a window, a doorway, and an attic window.[1]

The shed at the rear of the building consists of a brick section and a section covered in iron cladding. This shed currently contains the compressor installed in 1955. This machinery continues to supply compressed air to the wharves.[1]

The electrical workshop is not considered of cultural heritage significance.[1]

The Amenities Hall consists of a timber-framed structure located immediately north of the Electrical Shop. The building measures about 28 metres (92 ft) long and 8 metres (26 ft) wide, and has a small 2 by 2 metres (6 ft 7 in by 6 ft 7 in) structure added to the rear. The building houses the collections of the Maritime Archaeological Association of Far North Queensland.[1]

The building is a timber framed, gable-roofed structure placed on a concrete slab. The wall cladding consists of angular-rebated chamferboards. The original asbestos roof is in place. A loading door is present in the front (east) end of the building. The north and south walls of the building are symmetrically arranged with three double doors and five 6-paned windows down each side. Three 3-paned windows are present on the addition at the building's rear (west) end. Some of the original tables and benches, and the toiletries block are still in place.[1]

The Amenities Hall is not considered of cultural heritage significance.[1]

The ornamental gateposts at the number 2 gate are still in their original locations. The gateway consists of an entrance and exit lane separated by a concrete ornamental wall measuring about 2.5 metres (8 ft 2 in) wide and 4 metres (13 ft) tall. A concrete post flanks each side of the wall, and two gate hooks are affixed to each post. An ornamental coping is present on top of the wall. Low-relief Art Deco-style ornamentations are present on the wall faces, posts, and coping. Two matching single concrete posts are present on the opposite side of the entrance and exit lanes. These are also affixed with gate hooks, indicating that the original gates were double-hung and latched in the middle. The gates themselves are no longer present.[1]

The entrance and exit lanes inside the wharf compound are separated by a concrete-bordered garden bed. A flagpole base is present behind the entrance wall at the western end of the garden bed.[1]

Only the concrete gateway and side posts are deemed to be of cultural heritage significance. The concrete planter and flagpole are not considered culturally significant.[1]

The western edge of the 1945 concrete roadway is still visible, but the remainder is apparently underneath recent bitumen. Concrete U-shaped guttering is visible in front of the Amenities Hall and the Electrical Workshop, and may date to the original installation of the concrete roadway.[1]

The concrete roadway presumably dating to 1946 consists of the entrance and exit lanes at the number 2 gate. The lane on the south side is pitched down the middle to ensure water drains to either side.[1]

The concrete roadways are not considered of cultural heritage significance.[1]

Concrete slabs are present in the parking area immediately north of the number 2 gate roadway. The southernmost of these borders a landscaped area adjacent to the roadway on the south and merges with the 1945 roadway on the east. The western edge angles southwest towards the northern gate post. The outline of the northern edged of the slab is marked by two angular "bays". The northernmost slab consists of a strip of concrete extending east-west about 14 metres (46 ft) north of the first slab. The intervening area is now covered with bitumen, by 20 low "humps" are discernible. These are the remains of concrete support piers arranged in a block measuring 5 piers by 4 piers. These piers mark the location of the "Cairns Harbour Board Store" or "Beer Shed".[1]

The Harbour Board Store foundation is not of cultural heritage significance.[1]

Portions of two sets of tracks are visible. The portion of the first set within the area consists of a single set of double-rail tracks extending from the loading dock behind number 1 wharf southwards to the loading dock at the rear of number 3 wharf. The track extends past the original fixed 10-ton Cargo Crane behind the number 2 wharf. The tracks change from double-railed to single-railed near the southern end of the number 3 wharf loading dock.[1]

A short section of the second railway tracks is still in place approximately 6 metres (20 ft) west of the number 2 gate. Two sets of tracks spaced 3 metres (9.8 ft) apart are present in this location. Both sets are double-railed.[1]

Two concrete-bordered planters are present along the northern edge of the park. These planters are similar to the one currently located between the two vehicle lanes which pass through the number 2 gate.[1]

The Amenities Hall Park is not considered of cultural heritage significance.[1]

This Wikipedia article was originally based on "The Queensland heritage register" published by the State of Queensland under CC-BY 3.0 AU licence (accessed on 7 July 2014, archived on 8 October 2014). The geo-coordinates were originally computed from the "Queensland heritage register boundaries" published by the State of Queensland under CC-BY 3.0 AU licence (accessed on 5 September 2014, archived on 15 October 2014).