cut (Unix)

In computing, cut is a command line utility on Unix and Unix-like operating systems which is used to extract sections from each line of input — usually from a file. It is currently part of the GNU coreutils package and the BSD Base System.

cut
Original author(s)AT&T Bell Laboratories
Developer(s)Various open-source and commercial developers
Initial releaseFebruary 1985 (1985-02)
Operating systemUnix, Unix-like, IBM i
PlatformCross-platform
TypeCommand
Licensecoreutils: GPLv3+

Extraction of line segments can typically be done by bytes (-b), characters (-c), or fields (-f) separated by a delimiter (-d the tab character by default). A range must be provided in each case which consists of one of N, N-M, N- (N to the end of the line), or -M (beginning of the line to M), where N and M are counted from 1 (there is no zeroth value). Since version 6, an error is thrown if you include a zeroth value. Prior to this the value was ignored and assumed to be 1.

History

cut is part of the X/Open Portability Guide since issue 2 of 1987. It was inherited into the first version of POSIX.1 and the Single Unix Specification.[1] It first appeared in AT&T System III UNIX in 1982.[2]

The version of cut bundled in GNU coreutils was written by David M. Ihnat, David MacKenzie, and Jim Meyering.[3]

The cut command has also been ported to the IBM i operating system.[4]

Examples

Assuming a file named "file" containing the lines:

foo:bar:baz:qux:quux
one:two:three:four:five:six:seven
alpha:beta:gamma:delta:epsilon:zeta:eta:theta:iota:kappa:lambda:mu
the quick brown fox jumps over the lazy dog

To output the fourth through tenth characters of each line:

$ cut -c 4-10 file
:bar:ba
:two:th
ha:beta
 quick

To output the fifth field through the end of the line of each line using the colon character as the field delimiter:

$ cut -d ":" -f 5- file
quux
five:six:seven
epsilon:zeta:eta:theta:iota:kappa:lambda:mu
the quick brown fox jumps over the lazy dog

(note that because the colon character is not found in the last line the entire line is shown)

Option -d specified a single character delimiter (in the example above it is a colon) which serves as field separator. Option -f which specifies range of fields included in the output (here fields range from five till the end). Option -d presupposes usage of option -f.

To output the third field of each line using space as the field delimiter:

$ cut -d " " -f 3 file
foo:bar:baz:qux:quux
one:two:three:four:five:six:seven
alpha:beta:gamma:delta:epsilon:zeta:eta:theta:iota:kappa:lambda:mu
brown

(Note that because the space character is not found in the first three lines these entire lines are shown.)

To separate two words having any delimiter:

$ line=process.processid
$ cut -d "." -f1 <<< $line
process
$ cut -d "." -f2 <<< $line
processid

Syntax

cut [-b list] [-c list] [-f list] [-n] [-d delim] [-s] [file]

Flags which may be used include:

-b
Bytes; a list following -b specifies a range of bytes which will be returned, e.g. cut -b1-66 would return the first 66 bytes of a line. NB If used in conjunction with -n, no multi-byte characters will be split. NNB. -b will only work on input lines of less than 1023 bytes
-c
Characters; a list following -c specifies a range of characters which will be returned, e.g. cut -c1-66 would return the first 66 characters of a line
-f
Specifies a field list, separated by a delimiter
list
A comma separated or blank separated list of integer denoted fields, incrementally ordered. The - indicator may be supplied as shorthand to allow inclusion of ranges of fields e.g. 4-6 for ranges 4–6 or 5- as shorthand for field 5 to the end, etc.
-n
Used in combination with -b suppresses splits of multi-byte characters
-d
Delimiter; the character immediately following the -d option is the field delimiter for use in conjunction with the -f option; the default delimiter is tab. Space and other characters with special meanings within the context of the shell in use must be enquoted or escaped as necessary.
-s
Bypasses lines which contain no field delimiters when -f is specified, unless otherwise indicated.
file
The file (and accompanying path if necessary) to process as input. If no file is specified then standard input will be used.

See also

References

  1. cut  Commands & Utilities Reference, The Single UNIX Specification, Issue 7 from The Open Group
  2. cut(1)  FreeBSD General Commands Manual
  3. cut(1)  Linux General Commands Manual
  4. IBM. "IBM System i Version 7.2 Programming Qshell" (PDF). Retrieved 2020-09-05.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.