Drip irrigation

Drip irrigation is a type of micro-irrigation system that has the potential to save water and nutrients by allowing water to drip slowly to the roots of plants, either from above the soil surface or buried below the surface. The goal is to place water directly into the root zone and minimize evaporation. Drip irrigation systems distribute water through a network of valves, pipes, tubing, and emitters. Depending on how well designed, installed, maintained, and operated it is, a drip irrigation system can be more efficient than other types of irrigation systems, such as surface irrigation or sprinkler irrigation.

Open pressure compensated dripper

History

Ancient China

Primitive drip irrigation has been used since ancient times. Fan Shengzhi shu, written in China during the first century BCE, describes the use of buried, unglazed clay pots filled with water, sometimes referred to as Ollas, as a means of irrigation.[1][2]

Germany: subsurface pipe

Modern drip irrigation began its development in Germany in 1860 when researchers began experimenting with subsurface irrigation using clay pipe to create combination irrigation and drainage systems.[3]

Perforated pipe

The research was later expanded in the 1920s to include the application of perforated pipe systems.[4]

Australia: use of plastic

The usage of plastic to hold and distribute water in drip irrigation was later developed in Australia by Hannis Thill.[4]

Israel: plastic emitter

Usage of a plastic emitter in drip irrigation was developed in Israel by Simcha Blass and his son Yeshayahu.[5] Instead of releasing water through tiny holes easily blocked by tiny particles, water was released through larger and longer passageways by using friction to slow water inside a plastic emitter. The first experimental system of this type was established in 1959 by Blass, who partnered later (1964) with Kibbutz Hatzerim to create an irrigation company called Netafim. Together they developed and patented the first practical surface drip irrigation emitter.[3][4]

USA: drip tape

In the United States, the first drip tape, called Dew Hose, was developed by Richard Chapin of Chapin Watermatics in the early 1960s.[6][7][8] Chapin Watermatics was acquired by Jain Irrigation in 2006 and is housed under its US subsidiary Jain Irrigation Inc, USA.[9][10][11]

After its first introduction in California in the late 1960s, only 5% of irrigated land utilized this system by 1988. By 2010, 40% of irrigated land in California utilized this system.[12]

Significance

Modern drip irrigation has arguably become the world's most valued innovation in agriculture since the invention in the 1930s of the impact sprinkler, which offered the first practical alternative to surface irrigation.

Current developments

Careful study of all the relevant factors like land topography, soil, water, crop and agro-climatic conditions are needed to determine the most suitable drip irrigation system and components to be used in a specific installation.

Micro-spray heads

Drip irrigation may also use devices called micro-spray heads, which spray water in a small area, instead of dripping emitters. These are generally used on tree and vine crops with wider root zones.

Subsurface drip irrigation

Subsurface drip irrigation (SDI) uses permanently or temporarily buried dripperline or drip tape located at or below the plant roots. It is becoming popular for row crop irrigation, especially in areas where water supplies are limited, or recycled water is used for irrigation.

Global reach and market leaders

As of 2012, China and India were the fastest expanding countries in the field of drip- or other micro-irrigation, while worldwide well over ten million hectares utilised these technologies.[13] Still, this amounted to less than 4 percent of the world's irrigated land.[13] That year, Israel's Netafim was the global market leader (a position it maintained in 2018[14]), with India's Jain Irrigation being the second-biggest micro-irrigation company.[13]

Components and operation
Drip irrigation system layout and its parts
Nursery flowers watered with drip irrigation in Israel
Horticulture drip emitter in a pot

Components used in drip irrigation (listed in order from water source) include:

  • Pump or pressurized water source
  • Water filter(s) or filtration systems: sand separator, Fertigation systems (Venturi injector) and chemigation equipment (optional)
  • Backwash controller (Backflow prevention device)
  • Pressure Control Valve (pressure regulator)
  • Distribution lines (main larger diameter pipe, maybe secondary smaller, pipe fittings)
  • Hand-operated, electronic, or hydraulic control valves and safety valves
  • Smaller diameter polyethylene tube (often called "laterals")
  • Poly fittings and accessories (to make connections)
  • Emitting devices at plants (emitter or dripper, micro spray head, inline dripper or inline drip tube)

In drip irrigation systems, pump and valves may be manually or automatically operated by a controller.

Most large drip irrigation systems employ some type of filter to prevent clogging of the small emitter flow path by small waterborne particles. New technologies are now being offered that minimize clogging. Some residential systems are installed without additional filters since potable water is already filtered at the water treatment plant. Virtually all drip irrigation equipment manufacturers recommend that filters be employed and generally will not honor warranties unless this is done. Last line filters just before the final delivery pipe are strongly recommended in addition to any other filtration system due to fine particle settlement and accidental insertion of particles in the intermediate lines.

Drip and subsurface drip irrigation is used almost exclusively when using recycled municipal wastewater. Regulations typically do not permit spraying water through the air that has not been fully treated to potable water standards.

Because of the way the water is applied in a drip system, traditional surface applications of timed-release fertilizer are sometimes ineffective, so drip systems often mix liquid fertilizer with the irrigation water. This is called fertigation; fertigation and chemigation (application of pesticides and other chemicals to periodically clean out the system, such as chlorine or sulfuric acid) use chemical injectors such as diaphragm pumps, piston pumps, or aspirators. The chemicals may be added constantly whenever the system is irrigating or at intervals. Fertilizer savings of up to 95% are being reported from recent university field tests using drip fertigation and slow water delivery as compared to timed-release and irrigation by micro spray heads.

Properly designed, installed, and managed, drip irrigation may help achieve water conservation by reducing evaporation and deep drainage when compared to other types of irrigation such as flood or overhead sprinklers since water can be more precisely applied to the plant roots. In addition, drip can eliminate many diseases that are spread through water contact with the foliage. Finally, in regions where water supplies are severely limited, there may be no actual water savings, but rather simply an increase in production while using the same amount of water as before. In very arid regions or on sandy soils, the preferred method is to apply the irrigation water as slowly as possible.

Pulsed irrigation is sometimes used to decrease the amount of water delivered to the plant at any one time, thus reducing runoff or deep percolation. Pulsed systems are typically expensive and require extensive maintenance. Therefore, the latest efforts by emitter manufacturers are focused on developing new technologies that deliver irrigation water at ultra-low flow rates, i.e. less than 1.0 liter per hour. Slow and even delivery further improves water use efficiency without incurring the expense and complexity of pulsed delivery equipment.

An emitting pipe is a type of drip irrigation tubing with emitters pre-installed at the factory with specific distance and flow per hour as per crop distance.

An emitter restricts water flow passage through it, thus creating head loss required (to the extent of atmospheric pressure) in order to emit water in the form of droplets. This head loss is achieved by friction/turbulence within the emitter.

Advantages and disadvantages
Drip irrigation and spare drip irrigation tubes in banana farm at Chinawal, India
Pot irrigation by On-line drippers
Pressure compensated integral dripper on soilless without growing channels

The advantages of drip irrigation are:

  • Fertilizer and nutrient loss is minimized due to a localized application and reduced leaching.
  • Water application efficiency is high if managed correctly.
  • Field leveling is not necessary.
  • Fields with irregular shapes are easily accommodated.
  • Recycled non-potable water can be safely used.
  • Moisture within the root zone can be maintained at field capacity.
  • Soil type plays a less important role in the frequency of irrigation.
  • Soil erosion is lessened.
  • Weed growth is lessened.
  • Water distribution is highly uniform, controlled by the output of each nozzle.
  • Labour cost is less than other irrigation methods.
  • Variation in supply can be regulated by regulating the valves and drippers.
  • Fertigation can easily be included with minimal waste of fertilizers.
  • Foliage remains dry, reducing the risk of disease.
  • Usually operated at lower pressure than other types of pressurized irrigation, reducing energy costs.

The disadvantages of drip irrigation are:

  • Initial cost can be more than overhead systems.
  • The sun can affect the tubes used for drip irrigation, shortening their lifespan. (See Polymer degradation);
  • The risks of degrading plastic affecting the soil content and food crops. With many types of plastic, when the sun degrades the plastic, causing it to become brittle, the estrogenic chemicals (that is, chemicals replicating female hormones) which would cause the plastic to retain flexibility have been released into the surrounding environment.[15]
  • If the water is not properly filtered and the equipment not properly maintained, it can result in clogging or bioclogging.
  • For subsurface drip the irrigator cannot see the water that is applied. This may lead to the farmer either applying too much water (low efficiency) or an insufficient amount of water, this is particularly common for those with less experience with drip irrigation.
  • Drip irrigation might be unsatisfactory if herbicides or top dressed fertilizers need sprinkler irrigation for activation.
  • Drip tape causes extra cleanup costs after harvest. Users need to plan for drip tape winding, disposal, recycling or reuse.
  • Waste of water, time and harvest, if not installed properly. These systems require careful study of all the relevant factors like land topography, soil, water, crop and agro-climatic conditions, and suitability of drip irrigation system and its components.
  • In lighter soils subsurface drip may be unable to wet the soil surface for germination. Requires careful consideration of the installation depth.
  • Most drip systems are designed for high efficiency, meaning little or no leaching fraction. Without sufficient leaching, salts applied with the irrigation water may build up in the root zone, usually at the edge of the wetting pattern. On the other hand, drip irrigation avoids the high capillary potential of traditional surface-applied irrigation, which can draw salt deposits up from deposits below.
  • The PVC pipes often suffer from rodent damage, requiring replacement of the entire tube and increasing expenses.
  • Drip irrigation systems cannot be used for damage control by night frosts (like in the case of sprinkler irrigation systems)

Drip tape
Drip Irrigation T-tape

Drip tape is a type of thin-walled dripperline used in drip irrigation. The first drip tape was known as "Dew Hose".[16]

Drip tape duct tape is made of polyethylene and is sold flat on reels. The wall thickness typically ranges from 4 to 25 mils (0.1–0.6 mm). Thicker walled tapes are commonly used for permanent subsurface drip irrigation and thinner walled tapes for temporary throw-away type systems in high-value crops.

Water exits from tape through emitters or drippers. The typical emitter spacing ranges from 6 to 24 inches (150–600 mm). In some products, the emitters are manufactured simultaneously with the tape and are actually formed as part of the product itself. In others, the emitters are manufactured separately and installed at the time of production.

Some product is not a tape, but a thin-walled dripperline, but in popular parlance, both types of products are called tapes. Typical tape diameters are 5/8", 7/8", and 1-3/8", with the larger diameters more commonly used on permanent installations with longer runs.

Drip tape is a recyclable material and can be recycled into viable plastic resins for reuse in the plastics manufacturing industry.

Uses
Irrigation dripper

Drip irrigation is used in farms, commercial greenhouses, and residential gardens. Drip irrigation is adopted extensively in areas of acute water scarcity and especially for crops and trees such as coconuts, containerized landscape trees, grapes, bananas, ber, eggplant, citrus, strawberries, sugarcane, cotton, maize, and tomatoes.

Drip irrigation for garden available in drip kits are increasingly popular for the homeowner and consist of a timer, hose and emitter. Hoses that are 4 mm in diameter are used to irrigate flower pots.

See also

References
  1. s:zh:氾勝之書 以三斗瓦甕埋著科中央，令甕口上與地平。盛水甕中，令滿。
  2. Bainbridge, David A (June 2001). "Buried clay pot irrigation: a little known but very efficient traditional method of irrigation". Agricultural Water Management. 48 (2): 79–88. doi:10.1016/S0378-3774(00)00119-0.
  3. R. Goyal, Megh (2012). Management of drip/trickle or micro irrigation. Oakville, CA: Apple Academic Press. p. 104. ISBN 978-1926895123.
  4. "The History of the Drip Irrigation System and What is Available Now". www.irrigation.learnabout.info.
  5. "The History of Drip Irrigation".
  6. , Roberts, James C., "Drip irrigation tape"
  7. "US Patent # 5,387,307. Drip irrigation tape and method of manufacture - Patents.com". www.patents.com. Retrieved 2017-09-30.
  8. , Leal-Diaz, Jaime, "Hoses for irrigation by dripping and the like and the process to manufacture the same"
  9. "Jain Irrigation". www.JainsUSA.com. Retrieved 19 December 2017.
  10. "Jain Irrigation buys Chapin for $6 mn". Business Standard India. Press Trust of India. 2006-05-03. Retrieved 2017-09-30.
  11. User, Super. "New AG International - Jain Irrigation Announces Acquisition of Chapin Watermatics Inc". www.newaginternational.com. Retrieved 2017-09-30.
  12. Zilberman, Taylor; David, Rebecca (26 July 2015). "The Diffusion of Process Innovation: The Case of Drip Irrigation in California" (PDF).
  13. Drip Irrigation Expanding Worldwide, National Geographic, 25 June 2012, accessed 1 August 2019
  14. Tova Cohen, Israeli irrigation firm Netafim sees 50 pct earnings rise by 2020, Reuters.com, 21 March 2018, accessed 1 August 2019
  15. Yang, Chun Z.; Yaniger, Stuart I.; Jordan, V. Craig; Klein, Daniel J.; Bittner, George D. (1 July 2011). "Most Plastic Products Release Estrogenic Chemicals: A Potential Health Problem That Can Be Solved". Environmental Health Perspectives. 119 (7): 989–996. doi:10.1289/ehp.1003220. PMC 3222987. PMID 21367689.
  16. "DEW-HOSE Trademark - Registration Number 0847046 - Serial Number 72249303 :: Justia Trademarks". trademarks.justia.com. Retrieved 2016-06-12.

Further reading
  • Irrigation, 5th Edition, Muhammad Irfan Khan Yousafzai, Claude H. Pair, editor, published by the Irrigation Association, 1983
  • Trickle Irrigation for Crop Production, F. S. Nakayama and D. A. Bucks, editors, published by Elsevier, 1986, ISBN 0-444-42615-9
  • S. Blass, Water in Strife and Action (Hebrew), published by Massada limited, Israel, 1973
  • Maintenance Manual, published by Jain Irrigation Systems, 1989
  • Drip and Micro Irrigation Design and Management for Trees, Vines, and Field Crops, 5th Edition, by Charles M. Burt and Stuart W. Styles, published by the Irrigation Training and Research Center (ITRC), Cal Poly, San Luis Obispo, CA 93407–0721. www.itrc.org., 2016
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.