Electric light

Sign with instructions on the use of light bulbs

A tablet at St John the Baptist Church, Hagley commemorates the installation of electric light in 1934.

The modern incandescent light bulb, with a coiled filament of tungsten, and commercialized in the 1920s, developed from the carbon filament lamp introduced about 1880.

Less than 3% of the input energy is converted into usable light. Nearly all of the input energy ends up as heat that, in warm climates, must then be removed from the building by ventilation or air conditioning, often resulting in more energy consumption. In colder climates where heating and lighting is required during the cold and dark winter months, the heat byproduct has some value. Incandescent bulbs are being phased out in many countries due to their low energy efficiency.

As well as bulbs for normal illumination, there is a very wide range, including low voltage, low-power types often used as components in equipment, but now largely displaced by LEDs.

Halogen lamps are usually much smaller than standard incandescent lamps, because for successful operation a bulb temperature over 200 °C is generally necessary. For this reason, most have a bulb of fused silica (quartz) or aluminosilicate glass. This is often sealed inside an additional layer of glass. The outer glass is a safety precaution, to reduce ultraviolet emission and to contain hot glass shards should the inner envelope explode during operation. Oily residue from fingerprints may cause a hot quartz envelope to shatter due to excessive heat buildup at the contamination site. The risk of burns or fire is also greater with bare bulbs, leading to their prohibition in some places, unless enclosed by the luminaire.

Those designed for 12- or 24-volt operation have compact filaments, useful for good optical control. Also, they have higher efficacies (lumens per watt) and better lives than non-halogen types. The light output remains almost constant throughout their life.

Top, two compact fluorescent lamps. Bottom, two fluorescent tube lamps. A matchstick, left, is shown for scale.

Fluorescent lamps consist of a glass tube that contains mercury vapour or argon under low pressure. Electricity flowing through the tube causes the gases to give off ultraviolet energy. The inside of the tubes are coated with phosphors that give off visible light when struck by ultraviolet photons.[8] They have much higher efficiency than incandescent lamps. For the same amount of light generated, they typically use around one-quarter to one-third the power of an incandescent. The typical luminous efficacy of fluorescent lighting systems is 50–100 lumens per watt, several times the efficacy of incandescent bulbs with comparable light output. Fluorescent lamp fixtures are more costly than incandescent lamps, because they require a ballast to regulate the current through the lamp, but the lower energy cost typically offsets the higher initial cost. Compact fluorescent lamps are available in the same popular sizes as incandescent lamps and are used as an energy-saving alternative in homes. Because they contain mercury, many fluorescent lamps are classified as hazardous waste. The United States Environmental Protection Agency recommends that fluorescent lamps be segregated from general waste for recycling or safe disposal, and some jurisdictions require recycling of them.[9]

LED lamp with E27 Edison screw base

The solid-state light-emitting diode (LED) has been popular as an indicator light in consumer electronics and professional audio gear since the 1970s. In the 2000s, efficacy and output have risen to the point where LEDs are now being used in lighting applications such as car headlights and brake lights, in flashlights and bicycle lights, as well as in decorative applications, such as holiday lighting. Indicator LEDs are known for their extremely long life, up to 100,000 hours, but lighting LEDs are operated much less conservatively, and consequently have shorter lives. LED technology is useful for lighting designers, because of its low power consumption, low heat generation, instantaneous on/off control, and in the case of single color LEDs, continuity of color throughout the life of the diode and relatively low cost of manufacture. LED lifetime depends strongly on the temperature of the diode. Operating an LED lamp in conditions that increase the internal temperature can greatly shorten the lamp's life.

The 15 kW xenon short-arc lamp used in the IMAX projection system.

A mercury arc lamp from a fluorescence microscope.

Carbon arc lamps consist of two carbon rod electrodes in open air, supplied by a current-limiting ballast. The electric arc is struck by touching the rod tips then separating them. The ensuing arc produces a white-hot plasma between the rod tips. These lamps have higher efficacy than filament lamps, but the carbon rods are short-lived and require constant adjustment in use, as the intense heat of the arc erodes them. The lamps produce significant ultraviolet output, they require ventilation when used indoors, and due to their intensity they need protection from direct sight.

Invented by Humphry Davy around 1805, the carbon arc was the first practical electric light. It was used commercially beginning in the 1870s for large building and street lighting until it was superseded in the early 20th century by the incandescent light. Carbon arc lamps operate at high power and produce high intensity white light. They also are a point source of light. They remained in use in limited applications that required these properties, such as movie projectors, stage lighting, and searchlights, until after World War II.

A discharge lamp has a glass or silica envelope containing two metal electrodes separated by a gas. Gases used include, neon, argon, xenon, sodium, metal halide, and mercury. The core operating principle is much the same as the carbon arc lamp, but the term "arc lamp" normally refers to carbon arc lamps, with more modern types of gas discharge lamp normally called discharge lamps. With some discharge lamps, very high voltage is used to strike the arc. This requires an electrical circuit called an igniter, which is part of the electrical ballast circuitry. After the arc is struck, the internal resistance of the lamp drops to a low level, and the ballast limits the current to the operating current. Without a ballast, excess current would flow, causing rapid destruction of the lamp.

Some lamp types contain a little neon, which permits striking at normal running voltage, with no external ignition circuitry. Low pressure sodium lamps operate this way. The simplest ballasts are just an inductor, and are chosen where cost is the deciding factor, such as street lighting. More advanced electronic ballasts may be designed to maintain constant light output over the life of the lamp, may drive the lamp with a square wave to maintain completely flicker-free output, and shut down in the event of certain faults.

Many lamp units, or light bulbs, are specified in standardized shape codes and socket names. Incandescent bulbs and their retrofit replacements are often specified as "A19/A60 E26/E27", a common size for these kind of light bulbs. In this example, the "A" parameters describe the bulb size and shape while the "E" parameters describe the Edison screw base size and thread characteristics.