Expedition Everest

Office in queue

The attraction features a stand-by, Fastpass+, and a single-rider line.[1] The queue starts at the office of the fictional "Himalayan Escapes" travel agency, progressing to a replica temple with little holy figures. Visitors next enter a tea garden, followed by a room with equipment from a successful expedition, and then the "Yeti Museum", which contains information on the Yeti and a moulding of a Yeti footprint.[8] There are also about 8,000 artifacts brought from the Nepal trip in the museum.[9][10] The single-rider line skips all of the exhibits.

Artifacts from the "lost expedition"

The riders board the roller coaster in the model village of Serka Zong, to begin a speedy route through the Himalayas to the base of Mount Everest.[4][8]

The train departs the station to the right and climbs a small lift leading to a short drop, then circles around to the 118-foot (36 m) lift hill, carrying the riders into the mountain. On the way up it passes through a ransacked temple with murals of the yeti, warning the riders that the mountain is his territory. At the top of the mountain the train curves around the main peak and goes through a cave. When it emerges, it draws to a halt in front of track that has been torn apart, presumably by the yeti. The train itself is held in place by a series of rubber tires while an automatic switch rotates the piece of track directly behind the train. The train then rolls backwards along a new route that spirals down through the mountain. It eventually comes to a halt in a large cave, where riders see the yeti's shadow on the wall as he tears up more track. This effect distracts riders from noticing another automatic track switch in front of them. As the shadow moves away, the train rolls forward out of the mountain and down the main 80-foot (24 m) drop. It enters a 250° turn and speeds back up through another cave in the mountain, where the roars of the yeti are heard once more. The train exits from the rear of the mountain and enters a large helix before being lifted back into the mountain a final time. The train drops through a cave, where the yeti is reaching down toward it. On reaching the bottom of this drop, riders return to the unloading dock and depart into a gift shop. The ride lasts 2 minutes and 50 seconds.[8][11][12][13]

Expedition Everest has six steam-like trains, each with six cars. Each train has 17 rows seating two abreast, for a total of 34 riders per train. The trains are themed as the "Anandapur Rail Service" and are made to look old and rusty.[4][8] Riders must be at least 44 inches (110 cm) tall and are secured by a lap bar.[4][13] The "locomotive" itself is designed to resemble a vertical boiler configuration and is placed at the rear of the train rather than the front, so not to obstruct the riders' view. Up to five trains usually operate at once, but fewer can be used if guest demand is low.[1] To create the illusion of a "steam powered" train, engineers placed vents under the station. When a train comes into the station, steam comes up through the vents and enters the loading platform.[6]

The steel track is 4,424 feet (1,348 m) long and the lift is about 118 feet (36 m) high. Expedition Everest is the first ride to use Vekoma's newest track system, which places the rails on the outside of the ties rather than on the inside. This was the first large-scale installation of such a system.[12]

Expedition Everest is often compared to the 1959 Matterhorn Bobsleds roller coaster at Disneyland, which also features a snowy mountain setting and an "abominable snowman" figure throughout the ride.[17] Expedition Everest's mountain is made from 1,800 tons of steel and painted with 2,000 gallons of paint.[4][13] It is the tallest artificial mountain in the world, but not, as occasionally cited, the tallest point in Florida.[6] It is Disney's 18th mountain-themed attraction.[4][lower-alpha 1]

The artificial mountain is not a model of Mount Everest, but rather of the fictional "forbidden mountain" guarded by the yeti in the story created for the attraction by Walt Disney Imagineering. Everest is represented by the barren background peak on the far right, which is made to seem far in the distance (an example of forced perspective).[13]

The yeti is the largest and most complex audio-animatronic figure ever built by Walt Disney Imagineering.[6][8] It is 25 feet (7.6 m) tall. Its "skin" measures 1,000 square feet (93 m²), and is held in place by 1,000 snaps and 250 zippers. Its movement is controlled by 19 actuators when functioning in "A-mode", its full mode of operation. In "A-mode," it can move 5 ft (1.5 m) horizontally and 18 in (46 cm) vertically. The yeti's roars are provided by voice actor Fred Tatasciore.

A few months after the ride opened in 2006, the yeti figure's framing split, threatening catastrophic malfunction if it were to be operated further in "A-mode".[18] Since then it has been operated only in the alternative "B-mode", in which a strobe-light effect is used to give the appearance of movement, earning it the nickname "Disco Yeti" from some fans. It is speculated that the problem was caused by damage to the yeti's concrete base structure, which is unlikely to be repaired until a major refurbishment in the distant future, because the design limits access to the yeti without major disassembly of the superstructure.[19] The problem with the concrete is rumored to have occurred due to a glitch in the 4-D scheduling software that prevented adequate curing of a portion of the Yeti's foundation before the fabrication of mountain elements and roller coaster track.[20]

Joe Rohde, the Imagineer in charge of building the attraction and Animal Kingdom, was asked about the yeti at the 2013 D23 Expo. Rohde responded, "You have to understand, it's a giant complicated machine sitting on top of, like, a 46-foot tall tower in the middle of a finished building. So, it's really hard to fix, but we are working on it. And we continue to work on it. We have tried several 'things', none of them quite get to the key, turning of the 40-foot tower inside of a finished building, but we are working on it... I will fix the Yeti someday, I swear."[21][22]

In 2005, Disney, Discovery Networks, and Conservation International conducted expeditions to Nepal as part of the promotion for Expedition Everest. The purpose was to conduct scientific and cultural research in remote areas of the Himalayas, the location of the yeti legend. Participants included Joe Rohde from Walt Disney Imagineering and scientists from Conservation International and Disney's Animal Kingdom.[10]

The expeditions and the making of the attraction were chronicled in three documentaries broadcast on Discovery's cable television channels in April 2006.[7] The first was Expedition Everest: Journey to Sacred Lands, broadcast on the Travel Channel on April 9 to coincide with the attraction's grand opening.[7] The second, Building A Thrill Ride: Expedition Everest, was aired on April 10[7] and detailed the planning and construction of the ride, along with some of the ideas that made it possible. (During construction, for example, instead of traditional scaffolding the Imagineers used interior poles that poked through the outside of the mountain and were connected by wooden platforms.)[6] This documentary also featured survival tips from Les Stroud. The third, Corwin's Quest: Realm of the Yeti, was broadcast on Animal Planet on April 15 and featured American animal and nature conservationist Jeff Corwin.[7]

On February 15, 2006, Disney staged an elaborate publicity stunt called "Everest in the City" in New York City's Times Square. They draped large billboards over the sides of several buildings, depicting Everest with a coaster car careening down the mountainside and the yeti looking on from another peak, its eyes glowing red and flashing when the text message "Disney” was sent to “4Yeti” as provided by Disney.[23]