Gypsum concrete

US patent 4,444,925 lists the components of Gyp-Crete® as atmospheric calcined gypsum, sand, water, and small amounts of various additives. Additives listed include polyvinyl alcohol, an extender such as sodium citrate or fly ash, a surfactant such as Colloid defoamer 1513 DD made by Colloids, Inc., and a fluidizer based on sodium or potassium derivatives of naphthalene sulfonate formaldehyde condensate. One example mix is shown below.[3]

The purpose of the polyvinyl alcohol is to prevent the surface of the concrete from becoming dusty. While the exact mechanism is not known, it is thought that as the concrete sets, water migrates to the surface, bringing with it fine, dusty particles. When the water evaporates, the dusty particles are deposited on the surface. It is thought that the polyvinyl alcohol prevents the dusty particles from migrating upwards with the water.[3]

The mix is prepared on site using a specialized truck. The truck contains a tank for water, a mixing tank, a holding tank, a pump, and a conveyor for the sand and calcined gypsum. A hopper for the sand and gypsum is mounted externally on the vehicle.[4]

To prepare the mix, the sand and calcined gypsum are added to the hopper and mixed. Most of the required water is added to the mixing tank, then the sand and calcined gypsum are mixed in. Once all the sand and calcined gypsum have been mixed in, the rest of the water is added until the proper consistency is attained. Finally, the additives are mixed in and the whole batch of concrete is moved to the holding tank to be pumped out into the required area via long hoses. A small sample is taken from the batch and set aside so that the set-up time can be observed and adjustments can be made to the amount of additives so that the timing is correct.

Once the mix has been poured, little leveling, if any, is needed. The mix should be smoothed gently with a flat board, such as a 40” 1x4. This helps to concentrate the calcined gypsum at the surface.[4]

Gypsum concrete is lightweight and fire-resistant. A 1.5-inch slab of gypsum concrete weighs 13 pounds per square foot versus 18 pounds per square foot for regular concrete.[6] Even though gypsum concrete weighs less, it still has the same compressive strength as regular concrete, based on its application as underlayment or top coat flooring.[7] A 7-man work crew can lay 4–6 times as much gypsum concrete in a work day as regular poured Portland cement. This is due to the ease of leveling the very runny gypsum concrete versus normal concrete. In addition, if the wooden subfloor is first coated in a film of latex, the adhesion between the subfloor and the concrete is much better than the adhesion obtained with “normal” concrete. A further benefit is that nails can be driven through the cement into the subfloor without it chipping.[4] The cost of gypsum concrete is comparable to regular concrete, ranging from $1.75 per square foot to $6.00 per square foot.[8] Regular concrete ranges from $2.50 to $4.50 per square foot.[9]

In the late 1940s, copper tubing and Portland concrete were used to install radiant heat flooring. The copper tubes would be laid out around the ground and then the Portland concrete could be poured to cover the tubing and make an even base for the floor. However, this practice fell out of use in the United States within 15–20 years because the Portland concrete was too corrosive on the copper tubing. In the 1980s Gypsum concrete became widely used in the United States for radiant heat flooring. Plastic PEX tubing could be used with Gypsum concrete for radiant heat flooring without concern for corrosion on the PEX tubing.[10]

1. ^ The table in the patent lists the PVA content as 0.45 grains (0.00002%). Later on, it is stated that the PVA should be in a 1:0.005625 ratio with the calcined gypsum. This yields a PVA content of 0.45 lbs (0.16%).