Magnetic circuit

In electronic circuits, Ohm's law is an empirical relation between the EMF ${\displaystyle {\mathcal {E}}}$ applied across an element and the current I it generates through that element. It is written as:

${\displaystyle {\mathcal {E}}=IR.}$

where R is the electrical resistance of that material. There is a counterpart to Ohm's law used in magnetic circuits. This law is often called Hopkinson's law, after John Hopkinson, but was actually formulated earlier by Henry Augustus Rowland in 1873.[3] It states that[4][5]

${\displaystyle {\mathcal {F}}=\Phi {\mathcal {R}}.}$

where ${\displaystyle {\mathcal {F}}}$ is the magnetomotive force (MMF) across a magnetic element, ${\displaystyle \Phi }$ is the magnetic flux through the magnetic element, and ${\displaystyle {\mathcal {R}}}$ is the magnetic reluctance of that element. (It will be shown later that this relationship is due to the empirical relationship between the H-field and the magnetic field B, B=μH, where μ is the permeability of the material). Like Ohm's law, Hopkinson's law can be interpreted either as an empirical equation that works for some materials, or it may serve as a definition of reluctance.

Hopkinson's law is not a correct analogy with Ohm's law in terms of modelling power and energy flow. In particular, there is no power dissipation associated with a magnetic reluctance in the same way as there is a dissipation in an electrical resistance. The magnetic resistance that is a true analogy of electrical resistance in this respect is defined as the ratio of magnetomotive force and the rate of change of magnetic flux. Here rate of change of magnetic flux is standing in for electrical current and the Ohm's law analogy becomes,

${\displaystyle {\mathcal {F}}={\frac {d\Phi }{dt}}R_{\mathrm {m} },}$

where ${\displaystyle R_{\mathrm {m} }}$ is the magnetic resistance. This relationship is part of an electrical-magnetic analogy called the gyrator-capacitor model and is intended to overcome the drawbacks of the reluctance model. The gyrator-capacitor model is, in turn, part of a wider group of compatible analogies used to model systems across multiple energy domains.

Magnetic reluctance, or magnetic resistance, is analogous to resistance in an electrical circuit (although it does not dissipate magnetic energy). In likeness to the way an electric field causes an electric current to follow the path of least resistance, a magnetic field causes magnetic flux to follow the path of least magnetic reluctance. It is a scalar, extensive quantity, akin to electrical resistance.

The total reluctance is equal to the ratio of the MMF in a passive magnetic circuit and the magnetic flux in this circuit. In an AC field, the reluctance is the ratio of the amplitude values for a sinusoidal MMF and magnetic flux. (see phasors)

The definition can be expressed as:

${\displaystyle {\mathcal {R}}={\frac {\mathcal {F}}{\Phi }},}$

where ${\displaystyle {\mathcal {R}}}$ is the reluctance in ampere-turns per weber (a unit that is equivalent to turns per henry).

Magnetic flux always forms a closed loop, as described by Maxwell's equations, but the path of the loop depends on the reluctance of the surrounding materials. It is concentrated around the path of least reluctance. Air and vacuum have high reluctance, while easily magnetized materials such as soft iron have low reluctance. The concentration of flux in low-reluctance materials forms strong temporary poles and causes mechanical forces that tend to move the materials towards regions of higher flux so it is always an attractive force(pull).

The inverse of reluctance is called permeance.

${\displaystyle {\mathcal {P}}={\frac {1}{\mathcal {R}}}.}$

Its SI derived unit is the henry (the same as the unit of inductance, although the two concepts are distinct).

The reluctance of a magnetically uniform magnetic circuit element can be calculated as:

${\displaystyle {\mathcal {R}}={\frac {l}{\mu A}}.}$

where

l is the length of the element in metres,

${\displaystyle \mu =\mu _{r}\mu _{0}}$ is the permeability of the material (${\displaystyle \mu _{\mathrm {r} }}$ is the relative permeability of the material (dimensionless), and ${\displaystyle \mu _{0}}$ is the permeability of free space), and

A is the cross-sectional area of the circuit in square metres.

This is similar to the equation for electrical resistance in materials, with permeability being analogous to conductivity; the reciprocal of the permeability is known as magnetic reluctivity and is analogous to resistivity. Longer, thinner geometries with low permeabilities lead to higher reluctance. Low reluctance, like low resistance in electric circuits, is generally preferred.

The following table summarizes the mathematical analogy between electrical circuit theory and magnetic circuit theory. This is mathematical analogy and not a physical one. Objects in the same row have the same mathematical role; the physics of the two theories are very different. For example, current is the flow of electrical charge, while magnetic flux is not the flow of any quantity.

Analogy between 'magnetic circuits' and electrical circuits

Magnetic				Electric
Name	Symbol	Units		Name	Symbol	Units
Magnetomotive force (MMF)	${\displaystyle {\mathcal {F}}=\int \mathbf {H} \cdot \mathrm {d} \mathbf {l} }$	ampere-turn		Electromotive force (EMF)	${\displaystyle {\mathcal {E}}=\int \mathbf {E} \cdot \mathrm {d} \mathbf {l} }$	volt
Magnetic field	H	ampere/meter		Electric field	E	volt/meter = newton/coulomb
Magnetic flux	${\displaystyle \Phi }$	weber		Electric current	I	ampere
Hopkinson's law or Rowland's law	${\displaystyle {\mathcal {F}}=\Phi {\mathcal {R}}_{m}}$	ampere-turn		Ohm's law	${\displaystyle {\mathcal {E}}=IR}$
Reluctance	${\displaystyle {\mathcal {R}}_{\mathrm {m} }}$	1/henry		Electrical resistance	R	ohm
Permeance	${\displaystyle {\mathcal {P}}={\frac {1}{{\mathcal {R}}_{\mathrm {m} }}}}$	henry		Electric conductance	G = 1/R	1/ohm = mho = siemens
Relation between B and H	${\displaystyle \mathbf {B} =\mu \mathbf {H} }$			Microscopic Ohm's law	${\displaystyle \mathbf {J} =\sigma \mathbf {E} }$
Magnetic flux density B	B	tesla		Current density	J	ampere/square meter
Permeability	μ	henry/meter		Electrical conductivity	σ	siemens/meter

The resistance–reluctance model has limitations. Electric and magnetic circuits are only superficially similar because of the similarity between Hopkinson's law and Ohm's law. Magnetic circuits have significant differences that need to be taken into account in their construction:

• Electric currents represent the flow of particles (electrons) and carry power, part or all of which is dissipated as heat in resistances. Magnetic fields don't represent a "flow" of anything, and no power is dissipated in reluctances.
• The current in typical electric circuits is confined to the circuit, with very little "leakage". In typical magnetic circuits not all of the magnetic field is confined to the magnetic circuit because magnetic permeability also exists outside materials (see vacuum permeability). Thus, there may be significant "leakage flux" in the space outside the magnetic cores, which must be taken into account but often difficult to calculate.
• Most importantly, magnetic circuits are nonlinear; the reluctance in a magnetic circuit is not constant, as resistance is, but varies depending on the magnetic field. At high magnetic fluxes the ferromagnetic materials used for the cores of magnetic circuits saturate, limiting further increase of the magnetic flux through, so above this level the reluctance increases rapidly. In addition, ferromagnetic materials suffer from hysteresis so the flux in them depends not just on the instantaneous MMF but also on the history of MMF. After the source of the magnetic flux is turned off, remanent magnetism is left in ferromagnetic materials, creating flux with no MMF.

Magnetic circuit

Magnetic circuits obey other laws that are similar to electrical circuit laws. For example, the total reluctance ${\displaystyle {\mathcal {R}}_{\mathrm {T} }}$ of reluctances ${\displaystyle {\mathcal {R}}_{1},\ {\mathcal {R}}_{2},\ \ldots }$ in series is:

${\displaystyle {\mathcal {R}}_{\mathrm {T} }={\mathcal {R}}_{1}+{\mathcal {R}}_{2}+\cdots }$

This also follows from Ampère's law and is analogous to Kirchhoff's voltage law for adding resistances in series. Also, the sum of magnetic fluxes ${\displaystyle \Phi _{1},\ \Phi _{2},\ \ldots }$ into any node is always zero:

${\displaystyle \Phi _{1}+\Phi _{2}+\cdots =0.}$

This follows from Gauss's law and is analogous to Kirchhoff's current law for analyzing electrical circuits.

Together, the three laws above form a complete system for analysing magnetic circuits, in a manner similar to electric circuits. Comparing the two types of circuits shows that:

• The equivalent to resistance R is the reluctance ${\displaystyle {\mathcal {R}}_{\mathrm {m} }}$
• The equivalent to current I is the magnetic flux Φ
• The equivalent to voltage V is the magnetomotive Force F

Magnetic circuits can be solved for the flux in each branch by application of the magnetic equivalent of Kirchhoff's Voltage Law (KVL) for pure source/resistance circuits. Specifically, whereas KVL states that the voltage excitation applied to a loop is equal to the sum of the voltage drops (resistance times current) around the loop, the magnetic analogue states that the magnetomotive force (achieved from ampere-turn excitation) is equal to the sum of MMF drops (product of flux and reluctance) across the rest of the loop. (If there are multiple loops, the current in each branch can be solved through a matrix equation—much as a matrix solution for mesh circuit branch currents is obtained in loop analysis—after which the individual branch currents are obtained by adding and/or subtracting the constituent loop currents as indicated by the adopted sign convention and loop orientations.) Per Ampère's law, the excitation is the product of the current and the number of complete loops made and is measured in ampere-turns. Stated more generally:

${\displaystyle F=NI=\oint {\vec {H}}\cdot \mathrm {d} {\vec {l}}.}$

By Stokes's theorem, the closed line integral of H·dl around a contour is equal to the open surface integral of curl H·dA across the surface bounded by the closed contour. Since, from Maxwell's equations, curl H = J, the closed line integral of H·dl evaluates to the total current passing through the surface. This is equal to the excitation, NI, which also measures current passing through the surface, thereby verifying that the net current flow through a surface is zero ampere-turns in a closed system that conserves energy.

More complex magnetic systems, where the flux is not confined to a simple loop, must be analysed from first principles by using Maxwell's equations.