Microphone connector

Photo: 2.5 mm mono (TS), 3.5 mm mono and stereo (TRS), and 1/4″ (6.35 mm) stereo (TRS) phone connectors The most common microphone connector in consumer use is the venerable phone connector, in 1/4" (6.35 mm), 3.5 mm, and 2.5 mm sizes, and in both mono and stereo configurations. Not all microphone plugs with 3-segment TRS (Tip-Ring-Sleeve) connectors are actually stereo. Most computer microphones use the third segment to carry bias power for the microphone.

These round connectors are about 1 inch in diameter. They were in common use in the later 40's and thru the 50's at WELI, New Haven Connecticut. see: http://terryking.us/OldRadio/OP-4-RCA-RemoteAmplifier-1934-Rear.jpg The 3 connectors on the left are 1934 type "P" round microphone connectors. They look like this: http://terryking.us/OldRadio/P-CG-12S.jpg

These were "D" shaped upgrades of the old P connectors, with gold plated pins and sockets. They looked like this: http://terryking.us/OldRadio/UA-3-12.jpg

This is the part number for a Swichcraft connector used with high impedance microphones up through about 1980. It was intended for coax style cable up to 0.281 inches (7.1 mm) outside diameter.

Attachment is made with a 5/8-27 threaded ring that can be unthreaded over the body of the connector body allowing the female connector to become a male connector.

Wire connection was via solder. The center conductor is soldered to a hole resulting in a flat center contact. The cable shield is soldered to the strain-relief spring which is held in the body of the connector with a set screw.

With no provision for spring loading of the connection ring, vibration tends to loosen the threaded ring and create intermittent contact.

Popular microphone connector from 1930s to 1980s, originally manufactured by Amphenol. Amphenol sold this production to WPI Interconnect in early 1980s. The Amphenol 80-MC2M microphone connector was popular with American radio manufacturers (1950s to 1970s).

XLR3 cable connectors, female on left and male on right

Most commonly used on professional microphones, the common 3-pin XLR connector is a standard for transferring balanced audio among professional audio equipment.

The 4-pin XLR is the standard connector for intercom headsets, such as systems made by ClearCom and Telex. Two pins are used for the mono headphone signal and two pins for the unbalanced microphone signal.

The 4-pin XLR connector is also commonly used on amateur radio microphones, but transferring unbalanced audio instead, and using the 4th pin (with the common ground) for a push-to-talk (PTT) circuit activated by a button on the microphone. Some broadcast radio professionals also use these microphones, instead using the PTT circuit as a cough button (a momentary mute button) so that they may cough, clear their throat, or make comments to others in the studio without the sounds being broadcast. It is also used for dmx512 digital stage controls.

First used in the 1970s by Japanese radio manufacturers, as an alternative to the German DIN connector standard for microphone connectors on Citizens Band and Amateur Radio equipment, these screw-on circular connectors were available with 2, 3, 4, 5, 6, 7, or 8 pins. They often were used for other purposes as well, such as 1970s amateur radio transceivers (microphone), 1970s Kenwood mobile radios (2-pin, DC power), Eastern Asian manufacturers built soldering stations in 1990s using the conne tor fir the iron/handpiece connector.[1]

As reported by Philmore-Datel (LKG Industries of Rockford, IL), the USA importer and distributor for these connectors, the original Japanese mfg. (Foster) ceased production. After the 2011 Tōhoku earthquake and tsunami (loss of factories), connector manufacturing moved from Japan to Taiwan and mainland China manufacturers.

These connectors are sold under a variety of generic names: "CB connector", "Mobile connector", "Microphone connector", "Power connector" — even sometimes misidentified as XLR connectors.

The Chinese mainland (and Taiwan) manufacturers adopted this connector as the “GX16” (16mm), for “Power” or “Avionics” usage. You can find the Chinese “GX series” used as a multi-voltage connector (soldering stations, avionics, marine, etc.). Google or eBay search “GX16” , and you will find hundreds of vendors, such as Renhotecpro, based in Guangdong, China. http://www.renhotecpro.com/gx16-connector-data-sheet/

Renhotecpro has standardized the manufacturing of GX-series, in a variety of sizes, by the diameter of the connector (in mm): GX12, GX16, GX20, GX25, GX30, GX35, GX40.

Even though this circular connector is largely standardized, there was NO industry standard for wiring or pin usage/assignments. The individual pin assignments to specific functions varied from manufacturer to manufacturer. For example, in amateur radio, Icom, Kenwood, and Yaesu radios have all used the 8-pin screw-on connector, yet microphones from one brand are incompatible with the other two brands, at least without the use of an adapter cable in between the microphone and the radio.

Although originally designed for telephone usage and later adopted for computer networking, the Modular connector has been used for microphone connections extensively on modern amateur radio equipment, including models from the three major manufacturers (Icom, Kenwood, and Yaesu), but primarily used on mobile radio equipment (designed to be mounted in vehicles).

Like the screw-on round microphone connectors, there is little standardization among manufacturers, and even among different models from the same manufacturer, leading to significant interoperability problems when connecting non-OEM or homebrew microphones and other equipment.

Most radios with modular microphone connectors use the 8P8C (vernacular: RJ45) connector, but some use 6P6C or 4P4C connectors.