Nevada–Texas–Utah retort

The Nevada–Texas–Utah retort process (also known as NTU, Dundas–Howes or Rexco process) was an above-ground shale oil extraction technology to produce shale oil, a type of synthetic crude oil. It heated oil shale in a sealed vessel (retort) causing its decomposition into shale oil, oil shale gas and spent residue. The process was developed in the 1920s and used for shale oil production in the United States and in Australia. The process was simple to operate; however, it was ceased from the operation because of a small capacity and labor extensiveness.

NTU Retort
Process typechemical
Industrial sector(s)chemical industry
oil industry
FeedstockOil shale
Product(s)Shale oil
InventorRoy C. Dundas
Raymond T. Howes
Year of invention1923
Developer(s)NTU Company

History

The NTU retort was a successor of the 19th-century coal gasification retorts and it is considered as a predecessor of the gas combustion retort and the Paraho processes.[1][2] It was invented and patented by Roy C. Dundas and Raymond T. Howes in 1923. The process was improved by David Davis and George Wightman Wallace, a consulting engineer of the NTU Company.[2][3] In 1925, the NTU Company built a test plant at Sherman Cut near Casmalia, California.[1][4]

In 1925–1929, the process was tested by the United States Bureau of Mines in the Oil Shale Experiment Station at Anvil Point in Rifle, Colorado.[1][3] Retorting was carried out from 17 January to 28 June 1927. The plant was dismantled when work was terminated in June 1929.[3] One of the leading technologist involved in this stage was Lewis Cass Karrick, an inventor of the Karrick process.[5] In 1946–1951, two pilot plants with nominal capacities of 40 tons of raw oil shale were located at the same location. More than 12,000 barrels of shale oil was produced during this period. During the World War II, three NTU retorts were operated at Marangaroo, New South Wales, Australia.[1][6][7] Almost 500,000 barrels of shale oil was produced by these retorts by retorting local torbanite.[1]

Retort

The NTU retort was a vertical downdraft retort, which used internal combustion to generate heat for an oil shale pyrolysis (chemical decomposition). The retort was designed as a steel cylinder, lined with fire bricks. At the top it was equipped with an air supply pipe and at the bottom it was equipped with an exhaust pipe. The batch of crushed oil shale was loaded from the top; after that the retort was sealed. To start the pyrolysis process the fuel gas was ignited at the top of retort, and air injection into the retort started. The supply of fuel gas stopped after the upper quarter of the oil shale batch started to burn. At the same time the air injection continued bringing temperature in the burning part to about 1,500 °F (820 °C).

The heated gas caused a pyrolysis on the lower part of oil shale and produced shale oil and oil-shale gas are escaped from the retort through exhaust pipe at the bottom of retort. The pyrolysis occurred at the temperature about 800 °F (430 °C). By time-being, the combustion zones moved downward, and the char (semi-coke) produced as a solid residue of pyrolysis, ignited to burn as additional fuel for combustion. This caused the pyrolysis zone to move downward to the lower parts of retort. After combustion zone reached to the bottom of retort, air injection was stopped to stop combustion. After burning of char, the shale oil production ceased and only spent oil shale ash remained in the retort. The bottom of retort could opened for removal of the oil shale ash after retorting process. Operating the NTU retort with nominal capacity of 40 ton of raw oil shale, the full process cycle took about 40 hours.[1] The shale oil yield varied from 80% to 85% of Fischer assay.[2]

Advantages and disadvantages

The advantage of the NTU retort process was simple design, simple operation, and limited need for external fuel. It was suitable for processing of wide variety of oil shales. The disadvantage of this process was a batch mode of operation not allowing continuous retorting, and therefore having small capacity being labor extensive at the same time. The process also had a relatively low oil yield and it required cooling water.[1][8]

See also

References
  1. United States Office of Technology Assessment (June 1980). An Assessment of Oil Shale Technologies (PDF). DIANE Publishing. pp. 139–140. ISBN 978-1-4289-2463-5. NTIS order #PB80-210115. Retrieved 2009-07-06.
  2. Baughman, Gary L.; Hendrickson, Thomas A. (1978). Synthetic fuels data handbook: U.S. oil shale, U.S. coal, oil sands. Cameron Engineers. p. 67.
  3. Carter, George William; Jacobsen, Samuel Clark; Mackintosh, Helen Winchester Youngberg (1939). Low-temperature carbonization of Utah coals: a report of the Utah conservation and research foundation to the governor and state Legislature. Quality press. p. 373.
  4. "California, Oil Shale, Progress in 1925". Journal of the Institution of Petroleum Technologists. Institution of Petroleum Technologists. 12: 371. 1926. Retrieved 2009-07-08.
  5. Harris, Alan (2008-08-29). "The impact of an emissions trading scheme on the fuel and energy industry. Submission to the Senate Enquiry on Fuel and Energy" (PDF). Senate. Parliament of Australia: 2, 7, 10. Archived from the original (PDF) on 2009-10-02. Retrieved 2009-07-04. Cite journal requires |journal= (help)
  6. Prien, Charles H. (1951). "Pyrolysis of Coal and Shale". Industrial and Engineering Chemistry. 43. American Chemical Society. 43 (9): 2006–2015. doi:10.1021/ie50501a022.
  7. Mapstone, George E. (1950). "Wartime shale-oil production at Marangaroo, New South Wales". Oil shale and cannel coal; proceedings. 2. Institute of Petroleum. p. 489.
  8. "The NTU retorting process". Quarterly of the Colorado School of Mines. Colorado School of Mines Press. 69: 47. 1974.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.