Rowing

The beginning of rowing is clouded in history but the use of oars in the way they are used today can be traced back to ancient Egypt. Whether it was invented in Egypt or something learned from Mesopotamia via trade is not known. However, archaeologists have recovered a model of a rowing vessel in a tomb dating back to the 18-19th century BC.[3]

From Egypt, rowing vessels, especially galleys, were extensively used in naval warfare and trade in the Mediterranean from classical antiquity onward. Galleys had advantages over sailing ships: they were easier to maneuver, capable of short bursts of speed, and able to move independently of the wind.

During the classical age of oared galleys, the Greeks dominated the Mediterranean while the Athenians dominated the other Greeks. They used thousands of lower-class citizens to serve as rowers in the fleet.[4] The Classical trireme used 170 rowers;[5] later galleys included even larger crews. Trireme oarsmen used leather cushions to slide over their seats, which allowed them to use their leg strength as a modern oarsman does with a sliding seat. Galleys usually had masts and sails, but would lower them at the approach of combat. Greek fleets would even leave their sails and masts on shore (as being unnecessary weight) if possible.[6]

The use of oars in rowing instead of paddling came rather late to northern Europe, sometime between 500 BC-1 AD. This change might have been hastened by the Roman conquest of Northern Gaul. However, between 500 and 1100 AD, combined sailing and rowing vessels dominated trade and warfare in northern Europe in the time that has come to be known as the Viking Age.[7]

Galleys continued to be used in the Mediterranean until the advent of steam propulsion.

A forward-facing rowing technique used in the Slovenian pletna

Out on the lagoon at Toledo State Hospital in a rowboat

This is probably the oldest system used in Europe and North America. A seated rower pulls on one or two oars, which lever the boat through the water. The pivot point of the oars (attached solidly to the boat) is the fulcrum or the oar-lock. The motive force is applied through the rower's feet. In traditional rowing craft, the pivot point of the oars is generally located on the boat's gunwale. The actual fitting that holds the oar may be as simple as one or two pegs (or thole pins) or a metal oarlock (also called rowlock - "rollock"). In performance rowing craft, the rowlock is usually extended outboard on a "rigger" to allow the use of a longer oar for increased power.

Sculling involves a seated rower who pulls on two oars or sculls, attached to the boat, thereby moving the boat in the direction opposite that which the rower faces. In some multiple-seat boats seated rowers each pull on a single "sweep" oar, usually with both hands. Boats in which the rowers are coordinated by a coxswain are referred to as a "coxed" pair/four/eight. Sometimes sliding seats are used to enable the rower to use the leg muscles, substantially increasing the power available. An alternative to the sliding seat, called a sliding rigger, uses a stationary seat and the rower moves the oarlocks with his feet. On a craft used in Italy, the catamaran moscone, the rower stands and takes advantage of his body weight to increase leverage while sculling.[8]

Articulated or bow facing oars have two-piece oars and use a mechanical transmission to reverse the direction of the oar blade, enabling a seated rower to row facing forward with a pulling motion. An example of articulated oars is the RowVista forward rowing system, whose patent was issued in 2019. An opposite four-bar linkage reverses the movement direction of the oar handle and transfers it through a coupling rod to the oar blade. This specific mechanism also allows manual feathering of the oar blade, which is an essential part of the sculling motion.[9][10]

Push rowing, also called back-watering if used in a boat not designed for forward motion, uses regular oars with a pushing motion to achieve forward-facing travel, sometimes seated and sometimes standing. This is a convenient method of manoeuvring in a narrow waterway or through a busy harbour. The "Rantilla" system of frontrowing oars uses inboard mounted oarlocks rather than a reversing transmission to achieve forward motion of the boat with a pulling motion on the oars.

Another system (also called sculling) involves using a single oar extending from the stern of the boat which is moved side to side underwater somewhat like a fish tail, such as the Chinese yuloh, by which quite large boats can be moved.[11]

Sampans are rowed by foot in Ninh Bình Province of northern Vietnam.[12]

The Intha people of Burma row forwards using their legs.

The pletna of Slovenia is rowed forward in the standing position with two oars.

If the waterline beam (width) is too narrow the boat will be tender and the occupant at risk of falling out, if the beam is too wide the boat will be slow and have more resistance to waves. Overall beam (width) is important. If the rowlocks are too close together the oars will be difficult to use. If the rowlocks are too far apart then the boat will be overly large and rowing will be inefficient, wasting a rower's effort. Sometimes on narrow, faster rowboats for protected waters outriggers are added to increase rowlock separation.

If the freeboard (height of the gunwale above the waterline) is too high then windage will be high and as a result, the boat will be caught by the wind and the rower will not be able to control the boat in high winds. If the freeboard is too low, water will enter the boat through waves. If the boat is designed for one person then only a single rowing position is required. If the rower is to carry a passenger at the stern then the boat will be stern heavy and trim will be incorrect.

When it comes to how long the rowing boat should be, it is a compromise between two factors that will affect the speed of the boat. If the boat is too short, the boat will reach a very low maximum speed. If the boat is too long, there will be more friction and more wet surface. Therefore, the minimum recommended length should be around 16 feet. If the boat is longer than that recommended length, the boat is usually narrower and although faster will generally be more difficult to balance.

To have good width and the height that ensures the balance of the rowboat, a weight can be added in the bow, alternatively, the boat can supply a second rowing position further forward for this purpose.

There are some advantages and disadvantages that are attributed to the weight of the rowboat. A very light boat will most likely start to slow down as soon as the oar stroke has ended. In contrast, a heavier boat will likely continue to move forward.[17]

Most modern style rowboats are considerably lighter than traditional clinker-built style.[18]

A Sunnmørsfæring; a Norwegian four-oared rowing boat, from the region Sunnmøre (Herøy kystmuseum, Herøy, Møre og Romsdal, Norway)

Spring in the keel or rocker influences how a rowboat performs. Longer, slender race boats have less rocker of about 7.6 cm (3 in). A short 2.4-meter (8 ft) pram dinghy has a rocker of 15–18 cm (6–7 in). Boats with less rocker are easier to row and faster in flat or nearly flat water. However, in any waves a boat with 13–15 cm (5–6 in) of rocker will be more seaworthy—rising over waves rather than going through them. A boat with more rocker can change direction easily whereas a straight keel boat will track well in a straight line but resist turning. High sided and fine-ended boats, such as dories, are affected by wind. Their trim can be altered by using a plastic container of water attached to a rope that can be moved to the bow or stern as need be. Long-distance rowers can keep up a steady 20 strokes per minute compared to a racing shell which can be rowed at 32–36 strokes per minute by fit athletes.

A rower can maintain 40 strokes per minute for only a brief period. Longer, narrower rowboats can reach 7 knots (13 km/h; 8.1 mph) but most rowboats of 4.3 m (14 ft) can be rowed at 3–4 knots (5.6–7.4 km/h; 3.5–4.6 mph).[19] Many old rowboats have very full ends (blunt ends); these may appear at first glance to be bad design as it looks slow, not fast. However a full-ended rowboat will rise to a sea and not dig in as a finer hulled boat might do, thus a compromise needs to be made between the factors of speed and of seaworthiness. This style of rowboat was designed to carry a bigger load and the full sections gave far more displacement. Also older boats were often very heavily constructed compared to their modern counterpart, hence weighed far more. A rowing boat designed as a tender carrying occupants to a boat on a mooring might tend to be short, whilst a boat for use on rivers and to travel long distances might be long and narrow.