SS John Oxley

SS John Oxley is a steamship that previously served as a pilot boat and lighthouse and buoy tender.[2] The ship was built in Scotland in 1927 for the Queensland Government. The vessel was requisitioned by Royal Australian Navy during the World War II. Returned to her duties after the war, John Oxley remained active until 1968, when her deteriorating condition made her unusable. In 1970, the ship was donated by the Queensland Government to the Lady Hopetoun and Port Jackson Marine Steam Museum (now the Sydney Heritage Fleet) for preservation, but due to other projects, work was sidelined until 2004. As of 2017, the ship is undergoing restoration at Rozelle Bay.

John Oxley in July 2018, undergoing restoration at the Sydney Heritage Fleet shipyard in Rozelle Bay
History
Australia
Name: SS John Oxley
Owner:
Operator: Royal Australian Navy (World War II)
Builder: Bow, McLachlan & Co, Paisley, Scotland
Yard number: 464
Launched: 20 July 1927
In service: 1927
Out of service: 1968
Homeport:
Identification: IMO number: 5174234
Status: Undergoing restoration
General characteristics
Type: Pilot boat[1]
Tonnage: 544 GRT
Displacement: 760 DWT
Tons burthen: 212 NRT
Length: 168 ft (51 m)
Beam: 32 ft (9.8 m)
Draught: 11 ft (3.4 m)
Installed power: 1,400 IHP
Propulsion: triple expansion steam engine supplied by two Scotch boilers
Speed: 14 knots (26 km/h; 16 mph)
Capacity: 14 pilots
Crew: 15 crew
Armament: One Oerlikon 20 mm cannon (naval service)

Design and construction

Bow, McLachlan and Company of Paisley in Renfrewshire, Scotland built John Oxley in 1927, under yard number 464.[1] She was launched on 20 July 1927, and completed later that year.[1] The vessel is 168 feet (51 m) long, with a beam of 32 feet (9.8 m), and a draught of 11 feet (3.4 m).[1] Tonnage values are 544 Gross register tonnage, 760 Deadweight tonnage, and 212 Net Register Tonnage[1] Propulsion is provided by two Scotch marine boilers supplying a triple expansion steam engine, which delivers 1,400 IHP to the propeller, for a maximum speed of 14 knots (26 km/h; 16 mph).[1][2] The vessel had a crew of 15, and in her role as a pilot boat, could carry 14 harbour pilots.[1][3]

Service career

Wheelhouse with chartroom below, Sept 2013

In early October 1927, John Oxley left Greenock, Scotland bound for Brisbane via the Red Sea and Indian Ocean. While en route in the Mediterranean Sea, she responded to a distress signal by the tugboat Jackstay and towed it to Malta. It arrived in Brisbane on 9 December 1927.[4]

She was delivered to the Government of Queensland Harbours and Marine Department, whom she served as a pilot boat in Moreton Bay[1] and buoy tender and lighthouse tender along the Queensland coast.[2]

During World War II, John Oxley was requisitioned by the Royal Australian Navy and a 20mm Oerlikon anti-aircraft gun was mounted on the stern. She was returned to her former duties in 1946, and converted from coal to oil fuel that same year.

John Oxley continued to serve as a pilot tender, lighthouse and buoy tender until 1968 when she was decommissioned. In her later years she had become increasingly decrepit, such that in 1964 the Seamen's Union of Australia's journal called her a "rust heap" with "the worst living conditions of any ship on the entire Australian coast".[5]

Preservation

Restored steering engine in March 2014

John Oxley was donated to the Lady Hopetoun and Port Jackson Marine Steam Museum (now the Sydney Heritage Fleet) , arriving in Sydney in August 1970 and initially moored at Birkenhead Point.[2][6] She saw very little repair work until 1997, when restoration on another ship, the barque James Craig, was at a stage where she could be taken off the floating dock. Until then, its hull had gradually deteriorated and she was badly in need of repairs when put on the floating dock in place of the James Craig.

Since 2002 the John Oxley has been under continuous restoration on land at the Heritage dockyard of the Sydney Heritage Fleet, Rozelle Bay.[7] During eighty years on the water, the ship had incurred substantial corrosion to the hull, decks and superstructure. The majority of the plates of the ship's riveted hull have required complete replication using the same hot riveted method as when the ship was built.

The restoration work also entails the repair and reconditioning of all machinery, masts and rigging, timber work, internal fitout and generally making the ship seaworthy. The ship will satisfy the survey requirements for safe operation and make coastal voyages.[7]

References

Notes

  1. Cameron, Stuart; Robinson, George. "SS John Oxley". Clyde-built Database. Archived from the original on 4 March 2016. Retrieved 22 May 2011.CS1 maint: unfit URL (link)
  2. "History of John Oxley". Sydney Heritage Fleet. Archived from the original on 3 December 2017. Retrieved 3 December 2017.
  3. John Oxley Daily Commercial News & Shipping List 30 September 1927 page 5
  4. "NEW PILOT STEAMER". The Brisbane Courier (21, 801). Queensland, Australia. 10 December 1927. p. 28. Retrieved 4 December 2017 via National Library of Australia.
  5. Seaman's Union newspaper, reprinted in Seccombe, Ralph (August 2008). "Upstairs, Downstairs". Australian Sea Heritage. Sydney: Sydney Maritime Museum Ltd (92): 9–14.
  6. Ship Ahoy! Trolley Wire issue 131 December 1970 page 16
  7. "John Oxley restoration Update Jan 2011". Sydney Heritage Fleet. Archived from the original on 25 February 2011. Retrieved 22 May 2011.

Bibliography

Mollema, Hette (2010), SS John Oxley : Restoration Underway, Hette Mollema, ISBN 978-0-646-54234-8

This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.