Typhoon Kim (1980)

Map plotting the track and the intensity of the storm, according to the Saffir–Simpson scale

An area of disturbed weather developed in association with the monsoon trough that was situated near the equator on July 19. At 20:04 UTC, the Joint Typhoon Warning Center (JTWC) issued a Tropical Cyclone Formation Alert for the system, primarily because the disturbance was over warm water and low wind shear.[1] Four hours later, the Japan Meteorological Agency (JMA) classified the system as a tropical depression.[nb 1][3] Following reports from a Hurricane hunter plane of a well-defined surface circulation and winds of 40 to 50 km/h (25 to 30 mph), the JTWC classified the system as Tropical Depression 11 midday on July 20.[1] At the time, the depression was located over 600 km (375 mi) southeast of Guam.[4]

The depression tracked west-northwest, passing south of Guam and very near Ulithi around noon on July 21. Based on surface observations of 65 km/h (40 mph) on the island and data from Hurricane hunters, both the JTWC[1] and JMA upgraded the depression into a tropical storm at 18:00 UTC.[5] Post-storm analysis from the JTWC indicated that Kim attained tropical storm status six hours earlier,[6] despite aircraft data suggesting that the storm was not well stacked vertically. Further intensification was slow to occur as Kim tracked west-northwest, following Typhoon Joe across the Philippine Sea. At 06:00 UTC on July 23, a Hurricane hunter aircraft indicated falling pressures and the beginning of an eyewall.[1] Based on this, both the JTWC and JMA announced that Kim obtained typhoon intensity.[5] Around this time, the Philippine Atmospheric, Geophysical and Astronomical Services Administration (PAGASA) also began to monitor the storm and assigned it with the local name Osang.[7] Continuing to track west-northwest beneath a large subtropical ridge,[1] Kim began to clear out an eye on the evening of July 23;[4] subsequently, Kim, as forecast by the JTWC, entered a period of rapid deepening.[1] At 06:00 UTC July 24, the JTWC increased the intensity of Kim to 185 km/h (115 mph), equal to a Category 3 hurricane on the United States-based Saffir-Simpson Hurricane Wind Scale (SSHWS), while the JMA raised the winds to 170 km/h (105 mph).[5] Ten hours later, a Hurricane hunter aircraft measured a pressure of 908 mbar (26.81 inHg). This data justified the JTWC declaring Kim a super typhoon[1] and increasing the wind speed to 240 km/h (150 mph). At 18:00 on July 24, the JMA estimated that Kim reached its peak intensity to 170 km/h (105 mph) and assigned a pressure of 910 mbar (26.87 inHg).[5][nb 2]

Almost immediately thereafter, reports from the same Hurricane Hunter aircraft indicated that the pressure of the typhoon rose sharply, likely in response to decreased inflow caused by Kim's close proximity to land. The JTWC estimated that Kim made landfall along the coast of Luzon at an intensity of 185 km/h (115 mph),[1] while the JMA reported that Kim moved ashore with winds of 145 km/h (90 mph).[3] Continuing to weaken due to land interaction, Kim fell below typhoon intensity once it emerged into the South China Sea,[1] according to both the JTWC and JMA.[5] The JTWC expected Kim to revive over water in manner similar to Typhoon Joe, but this did not occur. The storm's inner core was disrupted by land, with Hurricane hunters constantly finding a poorly organized tropical cyclone. Kim began to move northwest in response to a weakness created in the subtropical ridge created by Joe. At 06:00 UTC on July 27, Kim crossed the coastline of China around 165 km (105 mi) northeast of Hong Kong.[1] At the time of its second landfall, both the JTWC and JMA estimated winds of 80 km/h (50 mph).[5] Twelve hours later, both the JTWC[6] and JMA ceased tracking Kim.[5]

Typhoon Kim caused widespread flooding across Luzon. In Manila, where floodwaters rose to more than 610 mm (24 in) in some suburbs, government offices and schools were closed. There, both Philippine Airlines and Philippine National Railways canceled all trips to the rest of the country.[9] The coast guard suspended sailing permits to ships throughout the country.[10] The Isabela province was the hardest hit by Typhoon Kim.[11] Almost 15 people were killed in the Cagayan province.[12] Across the Philippines, 40 people were killed,[13] 2 via drownings,[10] and 19,000 others were affected.[13] A total of 12,000 homes were destroyed and 5,000 villages were flooded.[4] Less than a week earlier, the same areas were affected by Typhoon Joe;[14][15] Kim was considered the more damaging of the two systems.[9]

The typhoon brought showers to much of southern China, extending as far north as Pratas Island, Taiwan (ROC). Wind gusts of 130 km/h (80 mph) were measured in the town of Shantou. In Hong Kong, a No 1. hurricane signal was issued on July 25. The next day, the signal was increased to a No 3. hurricane signal. All signals were dropped late on July 22, after Kim moved inland. A minimum pressure of 998.9 mbar (29.50 inHg) was recorded at the Hong Kong Royal Observatory (HKO) on July 27, around the time Kim made its closest approach to the city. On Waglan Island, a peak wind speed of 78 km/h (48 mph) was reported while a peak wind gust of 128 km/h (80 mph) occurred at Star Ferry. HKO observed 136.3 mm (5.37 in) of rain over a 72-hour period. Within the vicinity of Hong Kong, minor damage was reported and there were no injuries. Power was knocked out in the urban city of Kowloon. Some villages were flooded and two landslides occurred.[4]

• Other typhoons named Kim
• Similar early season Philippine typhoons
  • Typhoon Koryn (1993)
  • Typhoon Percy (1990)
  • Typhoon Peggy (1986)
  • Typhoon Vera (1983)