Vehicle bus

In automotive engineering, a vehicle bus is a specialized internal communications network that interconnects components inside a vehicle (e.g., automobile, bus, train, industrial or agricultural vehicle, ship, or aircraft). Special requirements for vehicle control such as assurance of message delivery, of non-conflicting messages, of minimum time of delivery, of low cost, and of EMF noise resilience, as well as redundant routing and other characteristics mandate the use of less common networking protocols. Protocols include Controller Area Network (CAN), Local Interconnect Network (LIN) and others. Conventional computer networking technologies (such as Ethernet and TCP/IP) are rarely used, except in aircraft, where implementations of the ARINC 664 such as the Avionics Full-Duplex Switched Ethernet are used. Aircraft that use AFDX include the B787, the A400M and the A380.

All cars sold in the United States since 1996 are required to have an On-Board Diagnostics connector, for access to the car's electronic controllers.

Background

The main driving forces for the development of vehicle network technology have been the advances made in the electronics industry in general and government regulations imposed, especially in the United States, in order to make the automobiles environmentally friendly.

With stringent emission standards for automobiles, it became impossible to attain the required degree of control without the help of on-board computing devices. On-board electronic devices have also contributed substantially to vehicle performance, occupant comfort, ease of manufacture and cost effectiveness.

At one time, a car radio was likely the only electronic device in an automobile, but now almost every component of the vehicle has some electronic feature. Typical electronic modules on today's vehicles include the Engine Control Unit (ECU), the Transmission Control Unit (TCU), the Anti-lock Braking System (ABS) and body control modules (BCM).

An electronic control module typically gets its input from sensors (speed, temperature, pressure, etc.) that it uses in its computation. Various actuators are used to enforce the actions determined by the module (turn the cooling fan on, change gear, etc.). The modules need to exchange data among themselves during the normal operation of the vehicle. For example, the engine needs to tell the transmission what the engine speed is, and the transmission needs to tell other modules when a gear shift occurs. This need to exchange data quickly and reliably led to the development of the vehicle network, as the medium of data exchange.

The automotive industry quickly realized the complexity of wiring each module to every other module. Such a wiring design would not only be complex, it would have to be altered depending on which modules were included in the specific vehicle. For example, a car without the anti-lock brake module would have to be wired differently than one that included anti-lock brakes.

The industry's answer to this problem was to create a central network in the vehicle. Modules could be 'plugged' into the network and would be able to communicate with any other module that was installed on the network. This design was easier to manufacture, easier to maintain and provided the flexibility to add and remove options without affecting the entire vehicle's wiring architecture. Each module, a node on the vehicle network, controls specific components related to its function and communicates with the other modules as necessary, using a standard protocol, over the vehicle network.

Networks were not new, but their application to the vehicle was. The networks for the vehicles called for:

  • Low cost
  • Immunity from external noise
  • Ability to operate in harsh environments
  • Overall robustness and reliability

Although the vehicle network made modest demands on data throughput, the demand for more on-board computing is continuing to drive changes to these networks to provide higher-speed communication between modules. The control area network include the receiver and transmitter for the host to controller transmission and interlinking between the computers

Protocols, physical media and connectors

There are several network types and protocols used in vehicles by various manufactures. Many companies are encouraging a standard communication protocol, but one has not been settled on.

Protocols

Common vehicle buses protocols include:

  • A²B - (Automotive Audio Bus) An audio distribution protocol developed by Analog Devices
  • AFDX
  • ARINC 429
  • Byteflight
  • CAN – (Controller Area Network) an inexpensive low-speed serial bus for interconnecting automotive components
  • D2B – (Domestic Digital Bus) a high-speed multimedia interface
  • FlexRay – a general purpose high-speed protocol with safety-critical features
  • IDB-1394
  • IEBus
  • I²C
  • ISO 9141-1/-2
  • J1708 and J1587
  • J1850
  • J1939 and ISO 11783 – an adaptation of CAN for commercial (J1939) and agricultural (ISO 11783) vehicles
  • Keyword Protocol 2000 (KWP2000) – a protocol for automotive diagnostic devices (runs either on a serial line or over CAN)
  • LIN – (Local Interconnect Network) a very low cost in-vehicle sub-network
  • MOST – (Media Oriented Systems Transport) a high-speed multimedia interface
  • Multifunction Vehicle Bus – part of the Train Communication Network IEC 61375.
  • SMARTwireX
  • SPI
  • VAN – (Vehicle Area Network)
  • UAVCAN – (Uncomplicated Application-level Vehicular Communication And Networking) mostly used in electric aircraft, drones, satellites, and robotics.

Physical transmission media

Some examples of physical transmission media use in vehicle networks:

Connectors

  • OBD-2 (16 pin)

Additionally, many major car manufacturers use their own proprietary vehicle bus standards, or overlay proprietary messages over open protocols such as CAN.

  • J1939 (9 pin)

Commercial class vehicles have Type-I or Type-II connectors that support CAN based communication per the SAE J1939 protocol.

Protocols usage

Vehicle Messaging Protocols
Protocol/VersionStart/End YearManufacturerVehicle Types
FlexRay2008?BMWcars
FlexRay2008?Volkswagencars
FlexRay2008?Daimler AGcars
FlexRayGeneral Motorscars
CAN1986Boschmany
MOST?Ford, BMW, Daimler, and GMcars
J1850GMcars
J18502008?Chryslercars
J1850Fordcars
APCFordcars
ISO-9141-I/-II2008?Fordcars
VAN2000?PSA Peugeot Citroëncars
VAN2008?Renaultcars
J19392005–presentmanyheavy trucks (Class 5-8)
J1708/15871985–presentVolvo AB, most US truck manufacturersheavy trucks (Class 5-8)

References

  1. Philips, E.H. (5 February 2007). "The Electric Jet". Aviation Week & Space Technology.
  2. "MiG-35 Multi-Role Combat Aircraft". Defense Update. Israel. 2009. Archived from the original on 14 March 2007. Retrieved 17 March 2007.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.