2010 Damghan earthquake

The 2010 Damghan earthquake (also known as the Kuh-Zar earthquake) occurred in northern Iran at 11:53:49 local time on August 27 with a moment magnitude of 5.8 and a maximum Mercalli intensity of VII (Very strong). This strike-slip event damaged and destroyed a number of small villages in a sparsely populated region near the Alborz mountain range. It left four people dead, forty injured, and about 800 people without homes. The deaths and injuries in this moderate event were attributed to the low quality construction styles that are typical of the area. The Iranian Strong Motion Network provided data by which seismologists determined the type and extent of the slip as well as the peak ground acceleration. Other large and destructive earthquakes have affected the Semnan Province, including several events in 856 AD and 1953.

2010 Damghan earthquake
Tehran
Torud
UTC time2010-08-27 19:23:49
ISC event15131413
USGS-ANSSComCat
Local dateAugust 27, 2010 (2010-08-27)
Local time11:53:49
Magnitude5.8 Mw [1]
Depth16.5 km (10.3 mi) [1]
Epicenter35.53°N 54.51°E / 35.53; 54.51 [1]
TypeStrike-slip [2]
Areas affectedSemnan Province, Iran
Max. intensityVII (Very strong) [2]
Peak acceleration.55g [3]
Casualties4 dead, 40 injured [2]
800 displaced [2]

Tectonic setting
See also: Caspian Depression, Geography of Iran, and Iranian Plateau

The tectonics of Iran are dominated by the continental collision of the Arabian and Eurasian Plates. The rate of convergence has been estimated at two centimeters per year for the past 10 million years; about half of that occurs across the Zagros fold and thrust belt. The northern Iran region near the Alborz mountains contains numerous reverse and left-lateral strike-slip faults that lie to the south of the Caspian sea. The Astaneh strike-slip fault was a likely source of the 856 Damghan earthquake that caused the largest loss of life in the history of Iran—more than 200,000 deaths.[4]

Earthquake
See also: Strike-slip tectonics
USGS ShakeMap for the event

A more recent damaging event that also occurred near the Alborz mountain range was the 1953 Torud earthquake, in which more than 900 perished. Like that shock, the 2010 Damghan event took place in a rural area that exposed relatively few villages to strong shaking. It occurred at 11:53 local time in the north-central desert region of Iran on a fault that dipped 78° to the northwest. Fault motion occurred on a NE-SW striking fault that was almost pure left-lateral strike-slip. A Mercalli intensity of VII (Very strong) was observed in Kuh Zar and the nearby villages of Tuchahi, Kelu, and Shimi. In Hoseynian, Moalleman, Satveh, and Torud, the intensity was VI (Strong). Some surface cracks and fissures were present near Tuchahi and Kelu villages, but no significant surface faulting occurred.[2]

Damage
See also: Unreinforced masonry building

The affected area has a low population density and has an abundance of homes that are constructed with local clay material by unskilled workers. The unreinforced stone masonry or adobe homes are sometimes overloaded single story structures with flat wooden roofs with steel beams. Most of these types of homes suffered partial collapse, and led to a number of roof collapses. Fifty homes were destroyed, three-hundred were damaged, including a roof cave-in that left two women dead. Overall, seven villages sustained damage and twelve were destroyed. Four people died, forty were injured, and 800 were left homeless, but no major infrastructure (dams, bridges, or power stations) were impacted.[3]

Strong motion
See also: Peak ground acceleration

The first isoseismal map that was created in Iran was for the earlier 1953 Torud event. In an effort to focus on the association between the macroseismic effects and the instrumental intensity for the 2010 event, seismologists Shahvar and Zaré conducted a field investigation and interviews. An isoseismal map that was created using the data aligned with a ShakeMap that was created by the Tehran-based International Institute of Earthquake Engineering and Seismology. The closest strong motion station was about 7 kilometers (4.3 mi) to the east of the origin of faulting, and showed a horizontal acceleration of .55g. The peak ground acceleration and peak ground velocity that were attained from the Iranian Strong Motion Network were considered large for a moderate event.[3]

See also

References
  1. ISC (19 January 2015), ISC-GEM Global Instrumental Earthquake Catalogue (1900–2009), Version 2.0, International Seismological Centre
  2. Shahvar & Zaré 2013, pp. 689, 690, 692, 693, 701, 702
  3. Shahvar & Zaré 2013, pp. 689, 690, 693–695, 701, 702
  4. Yeats, R. (2012), Active Faults of the World, Cambridge University Press, pp. 306, 313–315, ISBN 978-0521190855

Sources

  • Shahvar, M. P.; Zaré, M. (2013), "The 27 August 2010 Mw 5.7 Kuh-Zar earthquake (Iran): field investigation and strong-motion evidence", Natural Hazards, 66 (2): 689–706, doi:10.1007/s11069-012-0507-8

Further reading
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.