Q-Bus card list
A wide range of interface cards are available for Digital Equipment Corporation's Q-Bus.[1]
Part Number | Part Name | Form factor | Function |
---|---|---|---|
A012 | ADV11-A | 16-channel 12-bit A/D | |
A020 | 16-channel A/D, relay switched | ||
A026 | AXV11-C | 16-channel 12-bit A/D plus 2-channel 12-bit D/A | |
A6001 | AAV11-A | 4-channel 12-bit D/A | |
A6006 | AAV11-C | Digital-to-analogue converter | |
A8000 | ADV11-C | 16-channel 12-bit A/D | |
G7272 | Grant continuity card | ||
H223 | MMV11-A | 4-Kword 16-bit stack & drive assembly | |
H9270 | 4x4 Q-bus backplane | ||
H9273-A | 9x4 Q-bus backplane in AB only | ||
H9276-A | 9x4 Q-bus backplane, Q-22 | ||
H9281-BA | Q | 4x2 Q-bus backplane | |
H9281-BB | Q | 8x2 Q-bus backplane | |
L4002 | VAX 4000-500 CPU card | ||
M3104 | DHV11-A | 8-line async DMA MUX | |
M3106 | DZQ11-M | 4-line double-buffered async EIA MUX, with | |
M3106-PA | DZQ11-M | 4-line double-buffered async MUX with S-box | |
M3107 | DHQ11-M | 8-line async MUX module, DMA, Q-22 | |
M3108-A | DSV11-A | 2-line sync SLU for BA23/123 (-AA is first unit, | |
M3108-P | DSV11-S | 2-line sync SLU for BA223 (-SF is first unit, -SG | |
M3121 | DFA01-AA | Dual integral modem, S-box, DF224 compatible | |
M3125 | BITBUS to Q-bus interface | ||
M3125-PA | Q-22 bus interface to Intel BITBUS | ||
M3125-YA | Q-22 bus interface to Intel BITBUS, no handle | ||
M3126 | DFA01-BA | Dual integral modem, Q-bus, S-box, UK version | |
M3127-PA | DESQA-SA/SF | Ethernet/thinwire S-box adaptor (DELQA+DESTA) | |
M3127-PB | DESQA-SA/SF | M3127-PA with handle access thinwire pushbutton | |
M3128 | QBIC | Q-bus interface to VMI CCIC | |
M3129 | KMV11 | NRZI/RS422 data converter for KMV11 | |
M4002 | KWV11-C | Programmable realtime clock | |
M5010 | 32-bit non-isolated dc input module | ||
M5011 | 16-bit non-isolated dc input module | ||
M5012 | 16-bit isolated dc input module | ||
M5012-YA | 16-bit isolated dc input module (TTL compatible) | ||
M5013 | 8-bit isolated ac input module | ||
M5014 | Dual input counter, 16-bit | ||
M5016 | Quad input counter/prescalar, 8-bit | ||
M5031 | 16-channel isolated dc interrupt module, 16-bit | ||
M5976-AA | Q-bus to SCSI adaptor for BA23/BA123 enclosures | ||
M5976-SA | Q-bus to SCSI adaptor for BA200/BA400 enclosures | ||
M5977-AA | SCSI to Q-bus controller (MSCP/TMSCP) for 11/83 | ||
M6010 | 32-bit non-isolated dc output module | ||
M6010-YA | 32-bit non-isolated dc output module (TTL | ||
M6011 | Non-isolated dc one-shot output module | ||
M6012 | 8-bit isolated dc output module | ||
M6013 | 8-bit isolated ac output module | ||
M6014 | Dual 16-bit output converter | ||
M6015 | 16-bit retentive dc output module | ||
M7061 | VSV11-F | Raster graphics sync generator & cursor control | |
M7062 | VSV11-MA | Raster graphics image memory | |
M7064 | VSV11 | Raster graphics image processor card | |
M7066 | VTV01 | Video Display Sys: UNIBUS to Q-bus converter | |
M7135 | KD32-AA | microVAX I datapath with G floating point | |
M7135-YA | KD32-AB | microVAX I datapath with D floating point | |
M7136 | KD32-AA/AB | microVAX I memory control | |
M7142 | VK170-CA | Serial video module, CRT control logic, | |
M7164 | KDA50-Q | Q-bus SDI disk adaptor, Q-22 (1 of 2) | |
M7165 | KDA50-Q | Q-bus SDI disk adaptor, Q-22 (2 of 2) | |
M7168 | VCB02 | 4-plane colour bitmap module | |
M7169 | VCB02 | 4-plane video controller module | |
M7193 | DRQ11-CA | DMA interface, 16-bit | |
M7195-FA | MXV11-BF | 128-Kbyte RAM, 2 async EIA SLU, I/O, clock, | |
M7196 | TSV05 | TSV05 controller for Q/Q22 bus | |
M7264 | KD11-F | 11/03 processor with 4-Kword MOS RAM | |
M7264-AA | KD11-F | 11/03 processor with 4-Kword MOS RAM | |
M7264-AB | KD11-F | 11/03 processor with 4-Kword MOS RAM | |
M7264-BB | KD11-F | 11/03 processor with 4-Kword MOS RAM & DIBOL microm | |
M7264-CB | KD11-F | 11/03 processor with 4-Kword MOS RAM | |
M7264-DB | KD11-F | 11/03 processor with 4-Kword MOS RAM | |
M7264-EB | KD11-F | 11/03 processor with 4-Kword MOS RAM | |
M7264-FB | KD11-F | 11/03 processor with 4-Kword MOS RAM | |
M7264-HB | KD11-F | 11/03 processor with 4-Kword MOS RAM | |
M7264-JB | KD11-F | 11/03 processor with 4-Kword MOS RAM | |
M7264-YA | KD11-H | 11/03 processor with 0-Kword RAM | |
M7264-YB | KD11-Q | 11/03 processor with 0-Kword RAM & DIBOL microm | |
M7264-YC | KD11-H | 11/03 processor with 0-Kword RAM | |
M7268 | RKV11 | RK11-D to Q-bus adaptor | |
M7269 | RKV11 | RK05 controller | |
M727 | KA11 | 11/20 State control module | |
M727-YA | M727 for KH11-A | ||
M7270 | KD11-HA | LSI-11/2 CPU, 16-bit | |
M7458-AA | MSV11-RA | 1-Mbyte PMI/Q22 parity memory with CSR | |
M7500 | KMV1A-S | Programmable comms controller, BA2xxx. | |
M7502 | Single-line high speed intelligent communication | ||
M7504 | DEQNA-AA | Q-bus (Q-22) to ethernet adaptor, obsolete for VMS 5.x and above (use DELQA) | |
M7506-AA | MSV11-MA | 512-Kbyte 18-bit RAM | |
M7506-AT | MSV11-MA | 512-kbyte 22-bit parity/CSR MOS RAM | |
M7506-BA | MSV11-MB | 1-Mbyte RAM | |
M7506-BC | MSV11-MB | 1-Mbyte RAM | |
M7506-BE | MSV11-MB | 1-Mbyte 22-bit parity/CSR MOS RAM | |
M7506-BF | MSV11-MB | 1-Mbyte RAM | |
M7506-BH | MSV11-MB | 1-Mbyte RAM | |
M7506-BP | MSV11-MB | 1-Mbyte RAM | |
M7506-BT | MSV11-MB | 1-Mbyte 22-bit parity/CSR MOS RAM | |
M7506-BU | MSV11-MB | 1-Mbyte 22-bit parity/CSR MOS RAM | |
M7506-BV | MSV11-MB | 1-Mbyte 22-bit parity/CSR MOS RAM | |
M7512 | RQDX1E | RQDX extender for RQDX1; must be the last item in the backplane, below the RQDX1 | |
M7513 | RQDXE | RQDX extender for RQDX2/3 (-AA for BA23, -FA for | |
M7516 | DELQA-M | Ethernet interface (replaces DEQNA) | |
M7516-PA | DELQA | Q-22 high-performance ethernet adaptor | |
M7546 | TQK50-AA | TMSCP controller for TK50 tape unit | |
M7551-AA | MSV11-QA | 1-Mbyte 22-bit parity/CSR MOS RAM | |
M7551-BA | MSV11-QB | 2-Mbyte 22-bit parity/CSR MOS RAM | |
M7551-CA | MSV11-QC | 4-Mbyte 22-bit parity/CSR MOS RAM | |
M7554 | KDJ11-DA | J11 CPU 15 MHz, 512-Kbyte RAM, 2 SLUs, LTC | |
M7554-01 | KDJ11-DA | J11 CPU 15 MHz, 512-Kbyte RAM, 2 SLUs, LTC (VE) | |
M7554-02 | KDJ11-DB | 11/53-PLUS CPU | |
M7554-04 | KDJ11-DD | J11 CPU 18 MHz, 1.5-Mbyte RAM, 2 SLUs (CSS) | |
M7554-PA | KDJ11-SA | J11 CPU 15 MHz, 512-Kbyte RAM, 2 SLUs, S-box handle | |
M7554-PB | KDJ11-SB | J11 CPU 18 MHz, 512-Kbyte RAM, 2 SLUs, LAT PROM, | |
M7554-PC | CMR53-AA | J11 CPU 18 MHz, 512-Kbyte RAM, 2 SLUs, S-box handle, | |
M7554-SA | KDJ11-SA | J11 CPU 15 MHz, 512-Kbyte RAM, 2 SLUs, S-box handle | |
M7554-SC | KDJ11-SC | J11 CPU 15 MHz, 512-Kbyte RAM, 2 SLUs, S-box handle | |
M7554-SD | KDJ11-SD | J11 CPU 18 MHz, 1.5-Mbyte RAM, LAT ROM, S-box handle | |
M7554-SE | KDJ11-SE | J11 CPU 18 MHz, 1.5-Mbyte RAM, 2 SLUs, LTC, S-box | |
M7554-YA | KDJ11-SA | J11 CPU 15 MHz, 512-Kbyte RAM, 2 SLUs, LTC, | |
M7554-YB | KDJ11-SB | J11 CPU 15 MHz, 512-Kbyte RAM, 2 SLUs, LAT PROMs, | |
M7555 | RQDX3 | Winchester and floppy disk controller | |
M7555-YA | RQDX3-SD | Controller for RX33D 48TPI floppy disk drive | |
M7558 | 2-Mbyte 22-bit MOS memory | ||
M7558-AA | MSV11-SA | 2-Mbyte 22-bit parity/CSR MOS RAM | |
M7559 | TQK70 | TMSCP controller for TK70 | |
M7573 | RQDX4 | Controller for RX35, RD50/1/2/3/4 | |
M7602 | QVSS | Q-bus Video Sub System module for Q22 systems | |
M7602-YA | QVSS | Q-bus Video Sub System module, bitmap graphics | |
M7605 | TQK25 | 0.25" streaming tape drive controller (TK25) | |
M7606-AA | KA630-AA | microVAX II with 1-Mbyte, floating point, time of year clock, boot/diagnostic ROM (Q22-bus) | |
M7607-AA | MS630-AA | 1-Mbyte RAM for microVAX II (Q-22 via CD) | |
M7608-AA | MS630-BA | 2-Mbyte RAM for microVAX II (Q-22 via CD) | |
M7608-BA | MS630-BB | 4-Mbyte RAM for microVAX II (Q22-bus) | |
M7609-AA | MS630-CA | 8-Mbyte parity 36-bit RAM for microVAX II (Also M7609-AC, -AF, -AH, -AP, -AV) (Q-22 via CD) | |
M7616 | J11 CPU, 512-Kbyte RAM, 64-Kbyte PROM (Q22 peripheral processor) | ||
M7620 | KA650-AA/BA | microVAX III CPU (-AA full license, -BA | |
M7621 | MS650-AA | 8MB RAM for KA650 | |
M7622 | MS650-BA | 16MB RAM for KA650 | |
M7625 | KA655-BA | microVAX III CPU (workstation license), 60nS | |
M7626 | KA660 | VAX 4000 CPU, 57 MHz Q-22 DSSI ethernet | |
M7635-AA | KN210 | RISC 3000 CPU, Q-bus interface | |
M7635-AB | KN210 | M7635-AA with LSI R3000, R3020 chips | |
M7635-AC | KN210 | M7635-AA with PERF R3000, R3020 chips | |
M7651 | DRV11-WA | 18/22-bit DMA general purpose parallel interface | |
M7651-YB | DRV11-WA | M7651, revision C circuit | |
M7656 | VSV21-AA | Colour graphics module: M68K processor, HD63486 | |
M7676 | KXT11-AB | Single-board 16-bit dual-height CPU. | |
M7679 | ISDN | ISDN basic rate access Q-bus board | |
M7740 | RQC25 | Q22-bus to LESI bus adaptor used on disks with Also M7740-01, -PA) (Also called KLESI-QA) | |
M7940-YA | DLV11 | M7940 with extra wires to bring out clock & | |
M7940-YC | DLV11 | Modified M7940 for use in a tester, TTL in/out | |
M7940-YD | DLV11 | Modified M7940 for use in a tester, switchable | |
M7940-YE | DLV11 | Modified M7940 for use in a tester, XON/XOFF | |
M7941 | DRV11 | 16-bit parallel line unit | |
M7942 | MRV11-AA | Space for 4K 16-bit PROM | |
M7942-YA | MRV11-VA | VT71T bootstrap | |
M7942-YB | MRV11-AA | M7942 with VT52 emulator, VT71 bootstrap | |
M7942-YC | MRV11-VC | VT72 bootstrap/diagnostic module | |
M7942-YD | MRV11-AA | M7942 with CSR11 bootstrap | |
M7944 | MSV11-B | 4-Kword 16-bit MOS RAM (external refresh) | |
M7946 | RXV11 | RX01 floppy disk controller | |
M7948 | DRV11-P | LSI-11 bus foundation module. Basic Q-bus | |
M7949 | LAV11 | LA180 line printer control module | |
M7950 | DRV11-B | 16-bit DMA parallel general purpose interface | |
M7951 | DUV11-DA | Sync interface, character protocol; DU11-DA compat. | |
M7952 | KWV11-A | Programmable realtime clock | |
M7953 | MNCKW | MINC programmable real time clock | |
M7954 | IBV11 | IEC general purpose interface (GPIB) | |
M7955-AD | MSV11-CD | 16-Kword 16-bit MOS RAM with on-board refresh | |
M7957 | DZV11 | 4-line double-buffered async EIA MUX | |
M8006-PA | 72-bit opto-isolated output module | ||
M8007-PA | 72-bit opto-isolated input module | ||
M8012 | BDV11 | Bootstrap, power on self test, load program from Eproms and terminator card | |
M8013 | RLV11 | RL01 disk controller, 1 of 2 | |
M8014 | RLV11 | RL01 bus controller, 2 of 2 | |
M8016 | KPV11-A | Power fail, realtime clock, no termination | |
M8016-YB | KPV11-B | M8016 with 120-ohm termination | |
M8016-YC | KPV11-C | M8016 with 250-ohm termination | |
M8017-AA | DLV11-E/EC | Single-line async control module | |
M8017-PA | DLV11-E/EC | Single-line async control module, S-box handle | |
M8018 | KUV11-AA | Writable control store module | |
M8020 | DPV11-M | Single-line serial EIA sync interface | |
M8020-PA | DPV11-SA | Single-line serial sync interface, S-box handle | |
M8021 | MRV11-BA | 256-word RAM, space for 4-Kword UV PROM | |
M8027 | LPV11 | Printer interface module | |
M8028 | DLV11-F | Async interface EIA/20ma, error flags, break bit | |
M8029 | RXV21 | RX02 floppy disk drive control module | |
M8043 | DLV11-J | 4-SLU peripheral interface | |
M8044-AA | MSV11-DA | 4-Kword 16-bit MOS RAM (Also M8044-AB, -AC, -AD) | |
M8044-BA | MSV11-DB | 8-Kword 16-bit MOS RAM (Also M8044-BB, -BC, -BD) | |
M8044-CA | MSV11-DC | 16-Kword 16-bit MOS RAM | |
M8044-DA | MSV11-DD | 32-Kword 16-bit MOS RAM | |
M8045-AB | MSV11-EA | 4-Kword 18-bit MOS RAM | |
M8045-CH | MSV11-EC | 16-Kword 18-bit MOS RAM (Also M8045-CJ, -CK, -CL) | |
M8045-DA | MSV11-ED | 32-Kword 18-bit MOS RAM | |
M8047-AA | MXV11-AA | 4-Kword RAM, 2 async EIA SLU, sockets for 2 | |
M8047-CA | MXV11-AC | 16-Kword RAM, 2 async EIA SLU, sockets for 2 | |
M8047-HA | MXV11-HA | 16-Kword RAM, 2 async EIA SLU (8 bits + parity), | |
M8048 | MRV11-C | Universal PROM/ROM module with sockets for 16 | |
M8049 | DRV11-J | Hi-density parallel line unit (4 lines) | |
M8049-AA | DRV1J-SA/SF | Modification of DRV11-J to DRV1J-SA/-SF | |
M8049-PA | DRV11-J | M8049 with S-box handle | |
M8053 | DMV11 | Microprogrammed controller V.35, RS232/423, with | |
M8053-AA | DMV11 | Microprogrammed controller (needs one of M5930- | |
M8053-MA | DMV11-A | M8053 with DDCMP control ROM (point-to-point or | |
M8053-PA | DMV11 | M8053 with S-box handle | |
M8059-FA | MSV11-LF | 64-Kword MOS RAM, single voltage | |
M8059-KA | MSV11-LK | 128-Kword MOS RAM, single voltage | |
M8061 | RLV12 | RL01/RL02 disk control, 22-bit address | |
M8063-AA | KXT11-AA | FALCON (SBC-11/21) single-board CPU with 2 SLU, 1 parallel line unit, line frequency clock, | |
M8063-BA | KXT11-BA | FALCON (SBC-11/21) single-board CPU with 2 SLU, 1 parallel line unit, line frequency clock, | |
M8064 | DMV11 | Microprogrammed controller, integral modem, space | |
M8064-MA | DMV11 | M8064 with DDCMP point-to-point or multidrop, | |
M8067-FA | MSV11-PF | 128-Kbyte MOS memory with parity CSR | |
M8067-KA | MSV11-PK | 256-kbyte MOS memory with parity CSR | |
M8067-LA | MSV11-PL | 512-Kbyte MOS memory with parity CSR | |
M8185-YC | KDF11-AC | 11/23 CPU without options | |
M8186-YA | KDF11-AA | 11/23 CPU with KTF11-AA (MMU) and sockets for | |
M8186-YB | KDF11-AB | 11/23 CPU with KTF11-AA (MMU) AND KEF11-AA (FP11) | |
M8186-YC | KDF11-AC | 11/23 CPU without options | |
M8188 | FPF11 | Floating point processor | |
M8189 | KDF11-BA | 11/23-PLUS single-board CPU | |
M8190-AB | KDJ11-BB | J11 CPU 15 MHz with 2 boot & diagnostic ROMs, FPJ11 | |
M8190-AC | KDJ11-BD | J11 CPU 15 MHz with 2 boot & diagnostic ROMs, | |
M8190-AD | KDJ11-BA | J11 CPU 18 MHz with 2 boot & diagnostic ROMs, FPJ11 | |
M8190-AE | KDJ11-BF | Q/U 11/83-84 CPU J11 CPU 18 MHz with 2 boot & diagnostic | |
M8192 | KDJ11-A | LSI-11/73 CPU | |
M8192-YB | KDJ11-AB | LSI-11/73 CPU 8-Kbyte cache, FPJ11-AA compatible, | |
M8192-YC | KDJ11-AC | LSI-11/73 CPU 8-Kbyte cache with FPJ11-AA, no | |
M8194 | KDF11 | Data memory module | |
M8195 | KDF11 | Cache data path module | |
M8217 | DW11-A | UNIBUS to Q-bus interface module | |
M8377 | KXT11-CA | T11 16-bit single-board computer. Q-bus with a host processor | |
M8392-AA | 68020, 1-Mbyte, 2 x 8-channel UARTs | ||
M8392-BA | 68020, 1-Mbyte, 2 x 8-channel UARTs, S-box handle | ||
M8578 | MRV11-D | PROM/ROM module with 16 sockets; 24/28-pin devices Requires MXV11-B2 bootstrap ROM for bootstrapping | |
M8631-AA | MCV11-DA | 4-Kword 16-bit 2Kx8 static CMOS RAM with 96-hour battery backup (Also M8631-AF, -AL) (Q22-bus) | |
M8631-CA | MCV11-DC | 16-Kword 16-bit 2kx8 static CMOS RAM with 96-hour battery backup (Also M8631-CF, -CL) (Q22-bus) | |
M8634 | IEQ11-A | DMA version of IEEE(GPIB) interface | |
M8637-BA | MSV11-JB | 1-Mbyte ECC PMI RAM with CSR (Q22-bus) | |
M8637-CA | MSV11-JC | 2-Mbyte ECC PMI RAM with CSR (Q22-bus) | |
M8637-DA | MSV11-JD | 1-Mbyte ECC RAM | |
M8637-EA | MSV11-JE | 2-Mbyte ECC RAM | |
M8638 | HDLC DMA single channel sync MUX controller | ||
M8639-YA | RQDX1 | RD51/52 & RX50 control module | |
M8639-YB | RQDX2 | RD51/52 & RX50 control module, can be expanded | |
M8981-AA | KDJ11-EA | Q/U 11/93-94 CPU 18 MHz, DCJ11, FPJ11, 2-Mbyte parity | |
M8981-BA | KDJ11-EB | Q/U 11/93-94 CPU 18 MHz, DCJ11, FPJ11, 4-Mbyte parity | |
M9037 | Grant continuity | ||
M9047 | Grant continuity (also M9047-SA, -SF) | ||
M9058 | Distribution/adaptor/buffer board for RQDX1/2/3 | ||
M9400-YA | REV11-A | 120-ohm terminators with refresh & floppy boot | |
M9400-YB | TEV11 | 120-ohm terminators | |
M9400-YC | REV11-C | Refresh and boot alone | |
M9400-YD | REV11-D | Headers alone | |
M9400-YE | REV11-E | Headers and 250-ohm terminators can be used with M9401 as a Q-bus extender | |
M9400-YF | REV11-F | M9400-YA with boot sockets with no ROMs | |
M9400-YH | REV11-H | LDP/COMM boot & floppy boot with terminators | |
M9400-YJ | REV11-J | DMA refresh bootstrap, cable connector, 250-ohm | |
M9400-YK | REV11-K | M9400-YH with no terminators | |
M9400-YL | REV11-L | M9400-YH with cable connectors | |
M9400-YM | REV11-M | Refresh with DECnet bootstrap | |
M9400-YN | REV11-N | RX02 boot and refresh | |
M9401 | Mirror-image connector used at other end of cable | ||
M9404 | 1st Q22-bus cable connector, no terminators | ||
M9404-YA | Cable connector for expansion box, with 240-Ohm | ||
M9405 | 2nd Q22-bus cable connector, no terminators, mirror | ||
M9405-YA | M9405 with 120-Ohm terminators |
Q-Bus | |
Created by | Digital Equipment Corporation |
---|
References
- Microcomputer Products Handbook., Digital Equipment Corporation, 1985
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.