Dodge WC series

1934 K-39-X-4(USA) – Dodge's first Army 4x4 truck

The initial Dodge VC-series military models had a lot in common with this 1939 T-series pickup

Dodge had been the United States military's primary supplier of light wheeled vehicles, since before the U.S. joined the First World War.[15] After starting business in 1900, producing precision engine and chassis components for other car builders in Detroit — Ford and Oldsmobile chief among these — Dodge introduced their first car, the Model 30/35 tourer, in 1914. It was stronger and more high quality than the ubiquitous Ford Model T, and in 1916, Dodge cars proved their durability, both in the 1910s U.S.–Mexico Border War — the U.S. military's first operation to use truck convoys,[16] as well as in World War I, when some 12,800 Dodge cars and light trucks were used,[15] primarily as ambulances and repair trucks.,[17] but also as staff and reconnaissance vehicles. All the while, Dodge maintained its reputation for high quality truck, transmission, and motor parts they made for other successful manufacturers.

Dodge light trucks were initially based largely on their passenger cars, but later specific truck chassis and bodies were designed. Light- and medium-duty models were offered first, then a heavy-duty range was added during the 1930s and 1940s. Dodge developed its first four-wheel drive truck in 1934 — an experimental 1​¹⁄₂ ton for the U.S. Army, designated K-39-X-4(USA), of which 796 units were built in several configurations.[15][7] Timken supplied driven front axles and transfer-cases, which were added to a militarized commercial truck. The Timken transfer case was the first part-time design,[18] that allowed the driver to engage or disengage four-wheel drive using a lever inside the cabin.[17][19] In spite of the limited 1930s U.S. military budgets, the ’34 truck was liked well-enough that the 1​¹⁄₂ tonners were further developed. Dodge built the U.S. Army further batches of 4WD 1​¹⁄₂-ton cargo trucks in 1938, 1939 and 1940.[20] 1,700 RF-40-X-4(USA) trucks were procured in 1938, and 292 TF-40-X-4(USA) in 1939.[15] All of these 1​¹⁄₂-ton Army 4x4s rode on a 143 in (363 cm) wheelbase, and the 1938 RF-40 and 1939 TF-40 trucks were the first to receive a Dodge engineering code in the 200 range (T-200 and T-201 respectively).[7]

However, Dodge also eagerly pursued military contracts for half-ton four-by-fours at the same time. The smaller size had outperformed the 1​¹⁄₂-ton 4x4 during testing in 1938,[8] and Dodge had invested greatly in half- to one-ton trucks in prior years. In 1936, Dodge's light, car-based trucks had been crucially redesigned — dropping the old car frames and for the first time using modern, truck-style chassis, with side rails welded to the cross members on their half-ton to one-ton rated trucks.[21] Additionally, Dodge had built the all new, very large Warren Truck Assembly plant in Michigan for its light and medium trucks, opened in 1938. In 1939 again, Dodge presented a completely redesigned line of pickups and trucks: the art-deco styled, "Job-Rated" trucks, aimed to fit every job.[21]

1940 Dodge VC-5 Open Cab pickup. The classic, pre-war bucket seats attempted to keep occupants on board, prior to the introduction of seat belts.

1940 Fargo-badged truck at the Australian Army History Unit museum.

Dodge D15 Canadian Military Pattern truck, shared much with the 1940 VC-series.

Well before the onset of World War II, it was clear that the USA needed to update its military. The Quartermaster Corps (Q.C.), responsible at the time for providing the military with non-combat vehicles, moved to standardize truck designs, and by 1939, as the war in Europe exploded, the Army had settled on five payload-based general-purpose truck classes: ​¹⁄₂-ton, 1​¹⁄₂-ton, ​2 ¹⁄₂-, 4- and ​7 ¹⁄₂-ton.[22] By June 1940 the Q.C. had tested and approved its first three standard commercial based, all-wheel drive trucks: the 1​¹⁄₂-ton 4x4 Dodge, the GMC ​2 ¹⁄₂-ton 6x6 and a Mack 6-ton 6x6.[23] With regards to Dodge however, the U.S. military reconsidered its preferences for the build-up for the war almost immediately after this.

Whereas in 1936, a Marmon-Herrington converted Ford had become the Army's first half-ton 4-wheel drive,[24] and the Army had initially standardized Dodge's 1​¹⁄₂-ton 4x4 truck — following Dodge's push for building ​¹⁄₂‑tonners, after mid 1940 it was decided they preferred Dodge to build light-duty four-wheel drives, contracting for a series of half-ton trucks,[20] while GM / Chevrolet was instead going to become the standard supplier for 1​¹⁄₂-ton trucks.[5] So, when in the summer of 1940 the largest government truck contract awarded went to Chrysler's Dodge / Fargo Division, for more than 14,000 (mostly) 4x4 trucks,[25] this was in the midst of the transition, and thus included both orders for ​¹⁄₂‑ton and 1​¹⁄₂‑ton trucks, as GM / Chevy still needed to tool up for the 1​¹⁄₂-tonners.

Dodge had started developing designs for a 4x4 half-ton in 1939, and began production in earnest in 1940 — both 4x4 half-tons, as well as 1​¹⁄₂-ton 4x4 and 4x2 trucks. On all 1940 trucks, front sheetmetal was mostly identical to the commercial VC and VF models of that year, with the addition of a big brush guard mounted in front of the grille and headlights. Except for the addition of 4-wheel drive, and custom bodies on the ​¹⁄₂‑ton command cars, the trucks followed the 1939 procurement doctrine, to "use commercial trucks with only a few modifications such as brush guards and towing pintles to fit them for military use." [12]

The first of the ​¹⁄₂-ton, 4x4, VC series military trucks were based on Dodge's 1939 civilian, one-ton rated model TC-series. The military VC models retained the civilian engine and wheelbase, but gained four-wheel drive, and a new internal technical code: T-202. Manufacturing of the Dodge VC models (SNL number G-505) began in 1940, making these the Army's first production half-ton 4WD trucks. The soldiers also called the light command reconnaissance vehicles "jeeps," but this was also common with several other vehicles at the time.[26] — before that term migrated to the quarter-tons, gradually starting in 1941.[27][28]

A total of 4,640 VC models were built across six variants – mostly pick-ups and reconnaissance cars. On the one hand, these ​¹⁄₂‑ton VC trucks proved so successful, that much greater quantities were immediately ordered, and they were further developed into the G-505, ​¹⁄₂‑ton WC models built in 1941. On the other hand, an even lighter and smaller 4x4 truck was needed: a quarter-ton, that would soon replace the Dodges as the U.S.' lightest 4x4 military trucks. Although no longer standard, the VC trucks remained in use until the end of the war.[29]

The ​¹⁄₂-ton VC-series didn't include an ambulance, but the 1​¹⁄₂-ton VF-series did. The VF-407 was Dodge's first 4x4 military ambulance — only 3 were made.

In 1940, Dodge also built 6,472 four-wheel drive 1​¹⁄₂-ton trucks, under two U.S. contracts – one awarded to Dodge, and one to Fargo.[8][30][nb 7] The models VF-401 to VF-407 (or engine/tech type T-203 by Dodge – and G-621 by the Army), were a continuation of their experimental pre-war predecessors, the RF-40(-X) and TF-40(-X) (or T-200 / T-201), still riding on a chassis of the same 143 in (3.63 m) wheelbase. Production consisted of just over 6,000 closed cab, open bed cargo trucks, plus just under 400 dump-trucks.

Like on the ​¹⁄₂-ton VC-series, the 1940 VF-400 1​¹⁄₂-ton models simply used civilian front sheet-metal, based on the 1939 commercial model TE-30 cab, with a brush-guard fitted in front of the grille and headlights — but with a Dodge developed front driving axle, directional, cross-country tires, and a military cargo body.[31] Importantly, one thousand of the VF-400 series cargo trucks were equipped with a power take-off, gear-driven Braden model MU 10,000 lb (4,500 kg) capacity winch — a feature that was carried over on many of the subsequent ​¹⁄₂-ton and 1​¹⁄₂-ton WC series models, directly from 1941. And although the light-duty WC models that followed, did not receive the VF-400's two-speed transfer cases, these did return on the 1​¹⁄₂-ton WC-62 and WC-63. An ambulance model, VF-407, was also designed, but only three units were built, likely experimental.[1][32]

These proved to be the last of Dodge's 1​¹⁄₂-ton 4x4 trucks for the war. Although the Army had steadily taken the bulk of its trucks in this category from Dodge / Fargo up til then, further production of 1​¹⁄₂-ton 4x4 trucks was instead awarded to GM's Chevrolet G506, which became the standard in this segment for the rest of the war.[8]

Aside from four-wheel drive trucks, production started for a militarized commercial 1​¹⁄₂-ton, rear-wheel drive truck in 1940 — initially Dodge's model VF-31, cargo (engineering code T-98) under the government SNL number G-618. The 4x2 model VF-31 was succeeded by the model WF-31 (internally T-118) for 1941 (closed cab tractor) and 1942 (cab and chassis) — both on a 135 in (3.43 m) wheelbase — and the 1942 model WF-32, closed cab, stake and platform cargo truck, on a 160 in (4.06 m) wheelbase.[33][1] After a modest production of 516 units of the WF-31,[32] at least 9,500 Dodge WF-32 trucks were built, mostly for lend-lease to Russia.[34][35][36]

World War II soldiers called the ​¹⁄₂-ton 1940/1941 Dodge Reconnaissance / Weapon Carriers a "Jeep" before the Willys MB.[27][28]

External video
Dodge trucks in 1940 U.S. war promotion film
"Army on Wheels" – WW II-era U.S. Army exercise stock film on Periscope Archives. Made by the U.S. War Department, together with Dodge, the May 1940 film opens with news of 7,000 new Dodge trucks for use by Uncle Sam (from 02:34) — showing VC and VF models. The four-wheel drive off-road capability, ruggedness, and the diverse uses for the vehicles are expounded, for instance: officers employ portable desks in their command cars to study maps and plot strategies (mark 13:00).

All three light U.S. 4x4 trucks, nicknamed 'jeeps' in World War II: a Willys ​¹⁄₄‑ton, and Dodge ​³⁄₄‑ton and ​¹⁄₂‑ton (L to R).

The 1940 VC-series Dodge ​¹⁄₂-ton 4x4s were well liked but considered only an interim solution, because they were essentially a modified civilian truck. At the outset of World War II a more military design was laid out.[15] Dodge evolved the 1940 VC‑1 to VC‑6 into the equally half-ton rated WC series of military light trucks, produced in 38 model variants, of which 30 were four-wheel driven, in varying amounts — thousands of some models were produced, while only a few of some others were made. Where the military VC‑series still used much civilian sheet-metal, distinguished by a brush-guard in front of the grille — the WC‑series came with wide-open, almost flat fenders that prevented mud build-up, clogging rotation of the wheels — as well as a redesigned, sloping nose with an integrated, round, grated grille / brush-guard. A new ambulance with a fully enclosed, all-steel box rear body was designed, on a longer, 123 inch wheelbase; and PTO-driven winches were now fitted to some models.

The ​¹⁄₂‑ton WC models were the first all-military design Dodge developed in the build-up to full mobilization for World War II,[13] and they were the U.S. Army's first standard light 4x4 trucks — prior to the quarter-tons — when the U.S. formally declared war in December 1941.[15] Soldiers would sometimes call the new vehicles 'jeeps', as was still common practice before the term migrated to the yet to be introduced Willys and Ford trucks, and eventually stuck to those.[26]

Both the Dodge half-ton VC and WC trucks were part of the Army G-505 series. Some 77,750 four-wheel drive ​¹⁄₂‑ton WC numbered trucks were produced during late 1940 to 1942 under War Department contracts.[1][2][nb 2] Additionally, aside from the fully military 4WD models, a small total of 1,542 two-wheel drive units retaining civilian sheet-metal were also supplied to the U.S. military, bearing WC model numbers in this same range. These models carried the SNL-code G-613, and brought the total number of half-ton WC‑series up to some 79,300 units, and the grand total of all half-tonners (VC and WC; 4WD and 2WD) to almost 84,000.

The ​³⁄₄-ton and 1​¹⁄₂-ton T-214 redesign gave the Dodge WC series a distinctly different look and proportions.

In 1940 the Army revised its range of standard, payload-based, general-purpose truck classes: a ​¹⁄₄-ton chassis requirement was added; the ​¹⁄₂-ton was to be replaced by a ​³⁄₄-ton, and additional heavy categories were specified.[22] The Quartermaster General wanted to start direct negotiations with Dodge, GM and Mack for certain models immediately, but not until after February 1941 could the Quartermaster Corps choose manufacturers directly, based on their engineering and production capabilities.[22] One deciding factor had to do with availability of certain critical components, like transfer cases and especially constant-velocity joints, not used much on commercial trucks, but all-wheel drive vehicles all needed these; plus additionally, they would use two or three times the amount of driven axles, meaning more gears to cut for all the differentials. Produced up to the war by a few specialized firms with limited capacity, from spring 1942 Ford, Dodge and Chevrolet joined in fabricating these in mass quantity,[25] with Dodge's experience in making quality, precision parts dating back from the earliest beginnings of the company.

While very successful, the ​¹⁄₂-ton WC trucks had to be supplanted by new ​³⁄₄‑ton trucks. In late 1941, Dodge introduced a redesigned WC‑series 4x4 trucks uprated to ​³⁄₄‑ton and their SNL code changed to G-502. The ​³⁄₄‑ton featured a lower profile truck bed that could seat eight troops, plus under seat stowage compartments; while service-parts remained 80 percent interchangeable with the existing ​¹⁄₂‑ton series.[15] Maintaining 80% service parts interchangeability with the ​¹⁄₂‑ton models was of great value. The ​³⁄₄‑ton models could swiftly be deployed, and the ​¹⁄₂‑ton, G-505 WC‑trucks remained in use to the end of World War II.[13]

WC-62 armored car prototype (one built).

Throughout the war, Dodge was the U.S. Army's sole producer of ​³⁄₄‑ton trucks, and built a total of 255,193 of these across all variants from April 1942 to August 1945.[5][37][38] Standard vehicles in the ​³⁄₄‑ton 4x4 class were the WC-51 / WC-52 Weapons Carrier, WC-56 /-57 /-58 (Radio) Command Reconnaissance, WC-53 Carry‑all, and the WC-54 Ambulance. In the cargo/troop and command trucks, the WC-52 and WC-57 are identical to the WC-51 and WC-56, but with a longer frame, extending to carry the protruding front bumper with front-mounted winch.[39]

When the U.S. Army reorganized from using eight-troop rifle squads to twelve-men squads, the ​³⁄₄‑ton, 4x4, WC-51 and WC-52 trucks were also stretched into the 1943, G-507, 1​¹⁄₂‑ton, 6x6, troop and weapons carriers, to move 12-troop units per vehicle.

A single armored car prototype was built, based on the 1​¹⁄₂‑ton, 6x6, Dodge WC-62.

WC-9, WC-18, WC-27

Dodge WC-9 Ambulance

Entering production during 1941 to early 1942,[65] they were specifically designed to serve as military ambulances. These early variants are distinguishable from the later ones by having a curved radiator grille, while the later ones (WC-51 onwards) featured a flat grille. These versions were given a longer 123 in (3,100 mm) wheelbase.

• Length: 195 in (4.95 m)
• Width: 75 ¹³⁄₁₆ in (1.93 m)
• Height: 90 in (2.29 m)
• Weight: 5,340 lb (2,420 kg)
• Payload: 1,300 lb (590 kg)

Half-ton Carry-all (4x4 pictured)

WC-10, WC-17, WC-26, WC-36, WC-48

Carryall trucks with a nominal carrying capacity of 1,000 lb (450 kg). The WC-10, WC-17 and WC-26 followed engineering patterns T-207, T-211 and T-215 respectively — whereas the WC-36 and WC-48 were T-112, rear-wheel drive only models.

Command / reconnaissance cars

Lord Mountbatten, Allied Commander South East Asia, stands in a ​¹⁄₂‑ton WC Command Car near Mandalay, 1945.

Dodge WC-24 w. winch

WC-6, WC-15, WC-23

Command / reconnaissance cars.

WC-7, WC-24

Command / reconnaissance car with winch.

WC-8, WC-16, WC-25

Radio car / Command reconnaissance car with radio, 12 volt.

Dodge WC-14 pickup 1941

WC-1, WC-5, WC-12, WC-14, WC-40

Closed cab, two seater pickups with a nominal carrying capacity of a 1,000 lb (450 kg). Some portion of these models were manufactured with winch,[66] at least of the WC-12, the WC-14 (pictured), and the WC-40, reducing the payload to 700 lb (320 kg) — but no distinct model number was assigned for such units. The WC-12's engine displacement was increased to the T-215's volume of 230.2 cu in (3,772 cm³) mid-series, after engine No. 42001.[66]

Open cab ​¹⁄₂-tons, w/wo winch

WC-13 half-ton 4x4 with optional M24 machine gun mount.

Dodge WC-4 open cab with winch.

WC-3, WC-13, WC-21

Weapon carriers, two seater pickups with open cab. The open cab pickups could be fitted with an optional M24 machine gun mount, which bolted across the front of the bed. The mount could carry the M1918 Browning Automatic Rifle, as well as the M1919 Browning machine gun, and the 0.5 in (12.7 mm) M2 Browning machine gun.

• Length: 181 ¹⁄₁₆ in (4.60 m)
• Width: 75 ¹³⁄₁₆ in (1.93 m)
• Height: with top 88 ¹⁄₈ in (2.24 m)
• Weight: 4,440 lb (2,010 kg)
• Payload: 1,300 lb (590 kg)

WC-4, WC-22

Open cab weapons carrier, with Braden MU winch, and transverse seats, designed to tow the 37mm M3 anti-tank gun as well as carry the gun crew and ammunition. This type was usually issued to early tank destroyer units. 5570 built.

• Length: 191 ⁵⁄₁₆ in (4.86 m)
• Width: 75 ¹³⁄₁₆ in (1.93 m)
• Height: with top 88 ¹⁄₈ in (2.24 m)
• Weight: 4,775 lb (2,166 kg) net
• Payload: 1,000 lb (450 kg)

Half-ton 4x4 basic panel van.

WC-11, WC-19, WC-42

Almost 1,400 panel van trucks, and panel van bodied radio communication cars. At first, regular panel van trucks were ordered: 642 units of WC-11,[62][67] and 103 units of WC-19.[63] The subsequent WC-42 panel vans were however furnished and equipped as radio communication cars. The 650 WC-42 radio panel vans almost outnumbered their bare transportation siblings, and they were also the only radio communication cars that Dodge built in a panel van body style in the entire VC and WC series range.

WC-43 K-50 phone service truck

WC-39, WC-43, WC-50

These models were built as technical service trucks for the U.S. Army Signal Corps, designed to install and repair hard telephone lines. Together with some earlier ​¹⁄₂‑ton GMC/Chevrolet models, and the later ​³⁄₄‑ton WC-59 and WC-61, they were also known by the Signal Corps as the K-50 trucks.

Of the two-wheel drive WC-39 and WC-50, only a single unit of each were built, but the four-wheel drive WC-43 numbered 370 units.

M1 emergency repair truck, WC-41 — compare external picture here.

WC-5, WC-14, WC-20, WC-40, WC-41

Just over one thousand emergency repair chassis and trucks were ordered within the half-ton Dodge G-505, WC series.[62][63][68] The Dodge SNL G-657 Master Parts List doesn't explicitly list most of them as built to serve as emergency repair trucks, but the Summary Report of Acceptances, Tank-Automotive Materiel, 1940–1945, shows that at least 902 emergency repair chassis and trucks were received by the Army, and it involved at least all of the WC-14, WC-20 and WC-40 models, and most of the WC-41s.[69][70]

Dodge delivered at least all thirty WC-20, and most of the WC-41 units, as closed cabs with a bare chassis, on a 123 in (312 cm) wheelbase, fitted with dual rear tires.[69] Mostly furnished with third party utility service rear bodies, as M1 emergency repair trucks, for the purpose to provide mobile facilities for emergency ordnance repair (G-061 / G-505). One other body-type was ordered: one T-211 oil servicing truck in 1941.[63]

WC-54

1943 WC-54 Ambulance

The WC-54 Truck, 3/4 ton, 4×4 Ambulance, Dodge (G-502), was produced as an ambulance, but a few were modified to serve as radio/telephone trucks with the US Signal Corps. A total of 26,002 WC-54 units were built from 1942 through 1944, after which the ambulance was redesigned, and replaced by the WC-64 in 1945.[72][73]

• Length: 16 ft 3 in (4.95 m)
• Width: 6 ft 6 in (1.98 m)
• Height: 7 ft 6 in (2.29 m)
• Weight: 5,920 lb (2,685 kg)
• Payload: 1,800 lb (820 kg)

Dodge WC-64 Ambulance

WC-64

The WC-64 KD Truck, 3/4 ton, 4x4 Ambulance Dodge (G-502) was an ambulance based on the same chassis as the WC-54 but with a knock-down body designed to increase the number of vehicles that could be shipped at the same time. The rear boxes were supplied in two major parts: lower and upper. The lower part of the box was attached to the chassis at the factory, while the upper box was crated for installation in the field.[74] 3,500 Knock-down ambulances were built between the beginning of 1945 and the end of the war,[75] the great majority (2,531 units) went to allies under lend-lease: [76]

• 1,123 to the Free French forces
• 644 to British Commonwealth
• 475 to China
• 149 to Brazil and 82 to other Latin American republics

WC-53 Carry-all

Split tailgate shown on rear

WC-53

A carryall, mechanically the WC-53 was virtually identical to the WC-54 but was fitted with a body which was the 1939 civilian carryall modified to military specifications. All four rear side windows were wind-up opening and the seating consisted of front folding passenger seat to allow rear access, two person second row leaving space to access to the rear full width three person seat. The spare wheel was carried on a mount on the driver's side and although the door was fully operational it could not be opened and the driver had to enter from the passenger side. The rear end had split tailgates.[77][78]
WC-53s were also fitted as radio trucks with a bench on the left side with the operator seated sideways. 8,400 WC-53: Truck, 3/4 ton, 4×4 Dodge Carryall (G-502) were built. No carryalls came from the factory with a winch, though there was a field modification available.[79]

• Length: 15 ft 6 in (4.72 m)
• Width: 6 ft 7 in (2.01 m)
• Height: 6 ft 8 in (2.03 m)
• Weight: 5,700 lb (2,590 kg)
• Payload: 1,750 lb (790 kg)

WC-56

Rear of command car, desert tan

The WC-56 was wider and much shorter than the ​¹⁄₂‑ton command cars, giving it squat proportions.

The WC-56 Truck, Command Reconnaissance, 3/4 ton, 4x4 w/o Winch Dodge (G-502) was a command and reconnaissance vehicle akin to a large quarter-ton jeep. It did not prove popular as it was heavier and not as maneuverable as the jeep, and its distinctive profile made it a target. The soft-top included side-curtains, for better weather shielding. 21,156 units were built.[80][73]

• Length: 13 ft 10 in (4.22 m)
• Width: 6 ft 7 in (2.00 m)
• Height: 6 ft 9 in (2.07 m)
• Weight: 5,335 lb (2,420 kg)
• Payload: 1,750 lb (800 kg)

WC-57

Unlike jeeps, the Dodge command cars' soft-top included canvas sides (WC-57 with winch).

The WC-57 Truck, Command Reconnaissance, 3/4 ton, 4x4 w/Winch Dodge (G-502) was identical to the WC-56, but fitted with a Braden MU2 7,500 lb (3,402 kg) capacity winch at the front bumper. 6,010 units built.[80][73]

• Length: 14 ft 8 in (4.46 m)
• Width: 6 ft 7 in (2.00 m)
• Height: 6 ft 9 in (2.07 m)
• Weight: 5,644 lb ( 2,560 kg)
• Payload: 1,750 lb (800 kg)

WC-58

The WC-58 Truck, Radio, 3/4 ton, 4×4 w/o Winch, Dodge (G-502) was identical to the WC-56 Command / Reconnaissance Car, but fitted with a Signal Corps Radio set in front of the rear seat, and a 12-volt electrical system.[81][82] Some WC-58 models may have been built, based on the WC-57 with winch, as well.[15][83] A total of 2,344 radio equipped units were built,[82] but it is unclear whether these were included as part of the WC-56 / WC-57 production, or constituted an additional 2,344 WC-58 radio car units.

• Length: 13 ft 10 in (4.22 m) / 14 ft 7 in (4.46 m) with winch
• Width: 6 ft 7 in (2.00 m)
• Height: 6 ft 9 in (2.07 m)
• Weight: 5,644 lb (2,560 kg)
• Payload: 1,750 lb (800 kg)

With its top and bows down, the WC-51/52 followed the low-profile design doctrine – in Russian called the "Dodge 3/4"[14] – UMMC Museum of Military and Automotive Equipment, Verkhnyaya Pyshma, Russia.

Up to ten troops would fit in a WC-51 or WC-52. Shown WC-52 is identical to the WC-51, but with a power take-off front winch.

WC-51 and WC-52 Almost three quarters of Dodge's 255,195 total ​³⁄₄‑ton G-502 WC series production were built as WC-51 and WC-52, "Truck, Cargo, ​³⁄₄‑ton, 4x4, Weapons Carrier". 123,541 were built without winch as the WC-51, and 59,114 with a front winch as the WC-52 — for a total of 182,655 units. Including the 5,380 WC-55s M6 Gun Motor Carriages that were later downgraded back to WC-52s brought the total number to over 188,000 cargo, troops and weapons carriers.

With the top and bows down, the WC-51 and -52 followed the low-profile design doctrine of the time. Lack of a winch gave the WC-51 a 10 in (25 cm) shorter front overhang, and thus a better approach angle. The open cab pickup could be fitted with an optional M24A1 machine gun mount, which bolted across the front of the bed. The mount could carry the M1918 Browning Automatic Rifle, the M1919 Browning machine gun, or the M2 Browning machine gun.

The WC-52 not only differed from the WC-51 by having a power take-off driven Braden MU-2 7,500 lb (3,400 kg) capacity winch at the front bumper, but to accommodate it, the WC-52 was actually built on a different, longer frame. A winch was therefore not easily added in the field.

• Length: 13 ft 11 in (4.24 m) – 14 ft 9 in (4.48 m) with winch
• Width: 6 ft 11 in (2.11 meters)
• Height (with canvas cover): 6 ft 10 in (2.08 m)
• Height (with top down): 5 ft 2 in (1.57 m)
• Weight: 5,250 lb (2,382 kg) net – 5,550 lb (2,518 kg) net with winch
• Payload: 1,750 lb (800 kg)
• Tires: 9.00 x 16 in., 8ply

WC-51 cabin interior

A substantial amount, and almost a quarter of all ​³⁄₄‑ton weapons carriers (44,229 of both WC-51 and WC-52), were provided through Lend-Lease to the Allies[76]

• 24,902 to the Soviet Union
• 10,884 to Britain
• 3,711 to China
• 3,495 to the Free French forces
• 954 to Brazil and 204 to other Latin American countries

WC-55, M6 Gun Motor Carriage

WC-55

The M6 37 mm Gun Motor Carriage, 3/4-ton, 4×4 (abbreviated as M6 GMC), or fully described "M6 Fargo Gun Motor Carriage with 37mm Anti-tank Gun," (by Dodge numbered WC-55), was a modified G-502 Dodge WC-52, designed and built to carry an M3A1 37mm anti-tank gun combined with gun shield, mounted on its cargo bed, facing rearward. The WC-55 with gun combination was designated by Standard Nomenclature List supply catalog number G-121. A total of 5,380 were built by Fargo in 1942,[84] but most were later dismantled / downgraded and returned to service as WC-52 cargo trucks.

Fielded as a stopgap design from late 1942 in North Africa, in limited use with the US Army Tank Destroyer Battalions, and in the Pacific War in 1943/1944, improvements in enemy tanks quickly rendered the 37mm gun underpowered, and better guns became available. The WC-55 was first downgraded to "limited standard" in 1943, and subsequently declared obsolete, finally by early 1945.

• Length: 14 ft 8​¹⁄₂ in (4.48 m)
• Width: 7 ft 2 in (2.18 m)
• Height: 8 ft 2 in (2.49 m) to top of gun shield
• Weight: 5,600 lb (2 540 kg)
• Storage: 80 rounds of 37mm munitions

WC-59

WC-59, ​³⁄₄-ton K-50 telephone truck with ladder on side.

The WC-59 Truck, Telephone Maintenance, 3/4 ton, 4×4 Dodge (G-502) was designed to install and repair telephone lines. Based on the same chassis as the WC-54 ambulances, sharing a 23 in (58 cm) longer wheelbase than the regular ​³⁄₄‑ton WC series. The spare wheel was carried behind the seats, and a step ladder fitted where the spare wheel normally would have been. 549 units were built. The bespoke bed made it a K-50 truck to the Signal Corps. These were initially fitted to both Dodge and Chevrolet chassis.

• Length: 16 ft 0 in (4.88 m)
• Width: 6 ft 6 in (1.98 m)
• Height: 6 ft 9 in (2.06 m)
• Weight: 5,357 lb (2,430 kg)
• Payload: 1,750 lb (800 kg)

WC-61

WC-61 / K-50B truck

The WC-61 Light Maintenance Truck, 3/4 ton, 4×4 Dodge (G-502) was also designed to install and repair telephone lines. Replacement for the WC-59, the WC-61 had the step ladder mounted on the roof, the spare wheel was still fitted behind the seats, and the tool trunks were accessible from the outside. Just 58 were built. The US Signal Corps referred to these as the K-50B truck.

• Length: 15 ft 6 in (4.73 m)
• Width: 6 ft 10 in (2.08 m)
• Height (without ladder): 7 ft 5 in (2.26 m)
• Weight: 5,952 lb (2,700 kg)
• Payload: 1,750 lb (800 kg)

WC-60

Dodge WC-60 Emergency Repair Chassis, M2

The WC-60 chassis, fitted with a bed similar to the WC-61 by the American Coach and Body Co. of Cleveland, Ohio, formed the M2 Emergency Repair truck, 3/4 ton, 4×4 Dodge (SNL supply code G-061), a mobile workshop designed for field maintenance. Its open-topped service-type bed featured numerous tool trunks and stowage bins, accessible from the outside. 296 units were built.

• Length: 15 ft 6 in (4.73 m)
• Width: 6 ft 10 in (2.08 m)
• Height: 7 ft 5 in (2.26 m)
• Weight: 5,952 lb (2 700 kg)
• Payload: 1,750 lb (800 kg)

The G-507 Cargo and Personnel Carrier, 1​¹⁄₂-ton, 6x6 Truck, Dodge (WC-62 w/o Winch) was based on a lengthened WC-51 Weapons Carrier with an extra axle added. When the U.S. Army enlarged rifle squads from eight to twelve men, the ​³⁄₄‑ton no longer sufficed, and a 48-inch (1,200 mm) longer 6×6 variant was created that used most of the mechanical parts and some of the sheet metal of the G-502. The G-507 trucks could be driven by all six wheels (6x6) or by the four rear wheels only (6×4).[85] A number of components were strengthened in this design, and many of these changes were also incorporated in subsequent ​³⁄₄‑ton production. Production amounted to 43,224 units total,[5] — 23,092 WC-62 units without winch, and 20,132 WC-63 variants with winch.[73][4] One prototype was produced as an armored car.[86]

A total of 6,344 WC-62 and WC-63 cargo trucks were provided to World War II Allies — 4,074 to the Free French forces, 2,123 to British, and 137 units to Brazil.[76]

• Length: 17 ft 11 in (5.47 m)
• Width: 6 ft 11 in (2.11 m)
• Height (with canvas cover): 7 ft 3 in (2.21 m)
• Height (with top down): 5 ft 2 in (1.57 m)
• Weight: 6,925 lb (3,141 kg)
• Payload: 3,300 lb (1,500 kg)

The WC-63 Truck, Cargo and Personnel Carrier, 1​¹⁄₂ ton, 6×6 with Winch, Dodge (G-507) Weapons Carrier was based on a lengthened WC-52 with an extra axle added. Identical to the WC-62 but fitted with a PTO-powered Braden MU2 winch, initially of 5,000 lb (2,300 kg), later 7,500 lb (3,400 kg) capacity.

• Length: 18 ft 9 in (5.72 m)
• Width: 6 ft 11 in (2.10 m)
• Height (with canvas cover): 7 ft 3 in (2.21 m)
• Height (with top down): 5 ft 2 in (1.57 m)
• Weight: 7,175 lb (3,250 kg)
• Payload: 3,300 lb (1500 kg)