Ford Barra engine

This engine is found in the 6-cylinder variants of the BA Falcon (also derivative models Fairmont and Fairlane), and SX Territory, and was produced between late 2002 and mid 2005. This was the first Falcon engine that came standard with DOHC and Variable Cam Timing. This contributed to the significant jump in output over the base 157 kW SOHC Intech engine in the previous generation AU Falcon and a 10 kW gain over the Tickford enhanced VCT engine's 172 kW. It also kept Ford's engine power outputs above those of the Holden Ecotec and L67 supercharged V6 engines found in the Holden VY Commodore.

Power: 182 kW (244 hp) @ 5000 rpm

Torque: 380 N⋅m (280 lb⋅ft) @ 3250 rpm

Compression Ratio: 9.7:1

This engine is found in the BF Falcon and SY/SY II Territory, and was produced between late 2005 and early 2008. It is aesthetically the same and mechanically very similar to the Barra 182. Changes from its predecessor include an increase in compression ratio, a slight revision of the cam profiles, a revision of the air intake system, the introduction of dual independent variable camshaft timing, a secondary knock sensor and an upgraded ECU, which allowed for more sophisticated ignition timing and spark control. These changes lead to a slight increase in power to 190 kW.[3]

Power: 190 kW (255 hp) @ 5250 rpm

Torque: 383 N⋅m (282 lb⋅ft) @ 2500 rpm

Compression Ratio: 10.3:1

The Barra 195 is the last version of the naturally aspirated I6 engine and is found in the FG/FG-X Falcon and SZ/SZ II Territory. Changes from its predecessor include a new plastic inlet manifold & throttle body (replacing the broadband manifold intake which originated in the naturally aspirated EF Falcon) and a redesigned cylinder head with 'Fast Burn' swirl changes to the inlet port. These changes achieved power and economy improvements over the Barra 190.[4] The engine also moved to a rear sump design to suit the new FG Falcon front sub-frame.

Power: 195 kW (261 hp) @ 6000 rpm

Torque: 391 N⋅m (288 lb⋅ft) @ 3250 rpm

Compression Ratio: 10.3:1

This engine is found in the BA Falcon XR6 Turbo, and was produced between late 2002 and mid 2005. It is similar to the naturally aspirated Barra 182, except it has different pistons to lower the compression ratio, a single Garrett GT35/40r turbocharger, higher base fuel pressure, Inconel exhaust valves, red rocker cover, and an intercooler.[5]

Power: 240 kW (322 hp) @ 5250 rpm

Torque: 450 N⋅m (332 lb⋅ft) @ 2000-4500 rpm

Compression Ratio: 8.7:1

Barra 245T in a BF Falcon XR6T engine bay

This engine is found in the BF Falcon XR6 Turbo and the SY Territory Turbo, and was produced between mid 2005 and early 2008. It is internally very similar to its predecessor, with the 5 kW power increase found through the changes introduced by the Barra 190 (revised camshaft profiles and more powerful ECU, enabling dual independent VCT with an extra knock sensor). Aesthetically the engine is the same as the previous model, with the exception of the Territory Turbo using a black rocker cover and a top mounted intercooler. In May 2006, the engine received a minor internal upgrade which addressed concerns of bending con-rods, by introducing stronger con-rods.[6]

Power: 245 kW (329 hp) @ 5250 rpm

Torque: 480 N⋅m (354 lb⋅ft) @ 2000-4500 rpm

Compression Ratio: 8.7:1

Barra 270T from a BA-BF FPV

This engine is found in the BA/BF Falcon based FPV F6 Typhoon and Tornado models, and the SY Territory based FPV F6X, and was produced between 2004 and early 2009. It is the high-power variant of the Barra 240/245T versions found in the XR6 Turbo. The increase in power is achieved through the use of higher boost pressures from the otherwise under-utilised large Garrett GT3540 turbocharger, a larger intercooler, revised air intake. These are differentiated from the standard turbo engines by the unique FPV blue-coloured rocker cover. With the introduction of the BF Falcon in 2005, the 270T also inherited the upgrades found in the 245T, but the power figures were left unchanged.[7]

Power: 270 kW (362 hp) @ 5250 rpm

Torque: 550 N⋅m (406 lb⋅ft) @ 2000-4250 rpm

Compression Ratio: 8.7:1

This engine is found in the FG/FG-X Falcon XR6 Turbo, and was produced between mid 2008 and late 2016. Although the power figures for the revised turbo engine mimic the old FPV turbo I6, the engines are quite different. It has a redesigned low-profile log style intake manifold, a smaller turbocharger which spools faster, a new intercooler, redesigned pistons to increase compression. The end result is that the FG XR6 Turbo is faster than the FPV's BF Typhoon although they share the same power output. This engine introduces a transient over-boost feature for a maximum of 10 seconds when optimal atmospheric conditions are met when under full throttle, which increases torque to a maximum of 586 Nm.[8]

Power: 270 kW (362 hp) @ 5250 rpm

Torque: 533 N⋅m (393 lb⋅ft) @ 2000-4750 rpm

Compression Ratio: 8.8:1

This engine is found in the FG Falcon based FPV F6. It is the high-power variant of the FG XR6 Turbo's Barra 270T. It was produced between mid 2008 and mid 2014, ending production when FPV shut down. Featuring a larger turbocharger and intercooler, different pistons to reduce compression, and larger injectors than its less powerful sibling (the FG Barra 270T), it was the first engine manufactured in Australia to produce more than 100 hp (75 kW) per litre, producing 310 kW at the flywheel.

Power: 310 kW (416 hp) @ 5500 rpm[9]

Torque: 565 N⋅m (417 lb⋅ft) @ 1950-5200 rpm

Compression Ratio: 8.47:1

The final and most powerful variant of the Barra engine featured in the FG-X XR6 Sprint. This engine is the most powerful six cylinder produced in Australia and was built in very limited numbers, with only 500 for Australia and 50 for New Zealand (True production is 560, as 10 pre-production vehicles were built and auctioned off). Each engine had its own numbered build plaque attached to the rocker cover, which is painted in the same colour as the Territory Turbo rocker cover. The engine is based internally upon the Barra 270T, with extras added from the Barra 310T variant such as the turbo, intercooler and injectors. In an Australian first, Ford also employed a custom designed carbon fibre air intake which increased airflow by 45 percent. It was chosen to base the engine on the 270T instead of the 310T due to the increased compression ratio. The engine yet again employs Ford's over-boost feature, which when the correct conditions are met will increase engine output to 370 kW and 650 Nm.[10]

Power: 325 kW (436 hp) @ 6000 rpm

Torque: 576 N⋅m (425 lb⋅ft) @ 2750 rpm

Compression Ratio: 8.8:1

According to Ford Chief Program Engineer David Burn and Program Manager Justin Capicchiano, there are differences in the internals between turbo models, however no forged internals have been used.[11]

This engine was launched in 2002 with the BA Falcon and was a development of the Intech E-Gas engine. The E-Gas engine is designed to run on autogas only. It features a low-performance, high-reliability, low-maintenance Vialle closed-loop single-point venturi-style LPG-injector-less carburetion system in lieu of the standard sequential petrol injection system. This engine was carried over to the FG Falcon with only one option of a 4-Speed automatic transmission, without traction control but was replaced in mid-2011 by the EcoLPi system, which featured the ZF 6HP26 6-speed automatic transmission and traction control as per fitted to the petrol models.

Power: 156 kW (209 hp) @ 4750-5000 rpm

Torque: 374 N⋅m (276 lb⋅ft) @ 2750-3000 rpm

Compression Ratio (BA E-Gas): 10.7:1

Compression Ratio (BF / FG E-Gas): 10.3:1

This engine was launched in 2011 as a replacement for the E-Gas engine. It features a liquid phase injection autogas system, allowing for much higher power and torque than previously.[12]

Power: 198 kW (266 hp) @ 5000 rpm

Torque: 409 N⋅m (302 lb⋅ft) @ 3250 rpm

Compression Ratio: 12.0:1

On the 23rd of May 2013, Ford Australia confirmed that the Barra engine would be discontinued along with the Ford Falcon and Territory by October 2016. Ford Australia's engine manufacturing operations ceased on 26 September 2016 and car assembly on 7 October 2016. Ford Australia president Bob Graziano cited unprofitability due to high labour costs and dwindling market share for the demise of local manufacturing.[13]

This was an optional engine on the BA Falcon and was produced between October 2002 and October 2005.

Power: 220 kW (295 hp) @ 4750 rpm

Torque: 472 N⋅m (348 lb⋅ft) from 3250-4000 rpm (470 N⋅m (347 lb⋅ft) @ 3250RPM)

Introduced in October 2005 as an option for the BF Falcon, the Barra 230 introduced dual knock sensors instead of the single knock sensor on the BA Falcon. It also had more aggressive ignition calibration, slight increase in compression ratio various ECU modifications to comply with Euro III emissions standards.. This is done safely with the addition of another knock sensor. It was in production from 2005 until the release of the FG Falcon.

Power: 230 kW (308 hp) @ 5350 rpm

Torque: 500 N⋅m (369 lb⋅ft) @ 3500 rpm