Hartley TS16

The Hartley TS16 (Trailer Sailer 16 foot) is an Australian trailerable sailboat that was designed in 1956 by New Zealander Richard Hartley as a day sailer and which later became a one design racer.[1][2][3]

Hartley TS16
Development
DesignerRichard Hartley
LocationAustralia
Year1956
No. built1,800
Builder(s)Hartley Boat Plans
Boat
Boat weight794 lb (360 kg)
Draft4.07 ft (1.24 m)
Hull
TypeMonohull
ConstructionWood or fibreglass
LOA16.40 ft (5.00 m)
LWL14.00 ft (4.27 m)
Beam7.22 ft (2.20 m)
Hull appendages
Keel/board typeCentreboard
Rudder(s)transom-mounted rudder
Rig
Rig typeBermuda rig
I (foretriangle height)16.00 ft (4.88 m)
J (foretriangle base)5.50 ft (1.68 m)
P (mainsail luff)19.00 ft (5.79 m)
E (mainsail foot)11.00 ft (3.35 m)
Sails
SailplanFractional rigged sloop Masthead sloop
Mainsail area104.50 sq ft (9.708 m2)
Jib/genoa area44.00 sq ft (4.088 m2)
Total sail area148.50 sq ft (13.796 m2)

The design was based on a traditional New Zealand mullet fishing boat and was the first trailer sailer sailboat design built.[3] Hartley later designed the TS18 and TS21.[4]

Production

Most boats completed have been built by amateur builders using hand tools in residential garages and constructed of wood. Construction time is estimated at 400 hours. Later, some were commercially manufactured of fibreglass over a foam core. The boat was actually designed to fit into a garage. Construction plans are supplied by Hartley Boat Plans of Australia. About 1,800 boats have been completed.[1][3][5][6]

Design

The Hartley TS16 is a recreational keelboat, built predominantly of wood, or of fibreglass over a foam core, with wood trim. It has a fractional sloop rig, originally with wooden spars and later with aluminum. The hill has a slightly raked stem, a near-vertical transom, a transom-hung rudder controlled by a tiller and a centreboard. It displaces 794 lb (360 kg).[1][6]

The boat has a draft of 4.07 ft (1.24 m) with the centreboard extended and 9 in (23 cm) with it retracted, allowing beaching or ground transportation on a trailer.[1]

Operational history

A 2001 review in Australian Sailing described the design: "the boat that started the trailer-sailer movement, the Hartley 16 designed by New Zealander Richard Hartley in the early 1950s, still has good support and a very active class association in Australia. Hartley designed the boat for ease of construction in plywood with only hand tools by the home handyman. Although boats have been built professionally in fibreglass foam/sandwich, the most common way of getting on the water in a new boat is to build it in timber from the official plans..."[6]

See also

References

  1. McArthur, Bruce (2020). "Hartley TS16 sailboat". sailboatdata.com. Archived from the original on 9 November 2020. Retrieved 9 November 2020.
  2. McArthur, Bruce (2020). "Richard Hartley 1920 - 1996". sailboatdata.com. Archived from the original on 9 November 2020. Retrieved 9 November 2020.
  3. THE Hartley TS16 Assoc. of Australia. "History". www.australianhartleyts16.org.au. Archived from the original on 30 October 2019. Retrieved 15 November 2020.
  4. Yachting Victoria Trailable Yacht Division (2020). "Class Specifications". www.trailableyacht.com.au. Archived from the original on 23 November 2020. Retrieved 23 November 2020.
  5. McArthur, Bruce (2020). "Hartley Boat Plans (Australia)". sailboatdata.com. Archived from the original on 9 November 2020. Retrieved 9 November 2020.
  6. "Affordables" (PDF). Australian Sailing. October 2001. Archived (PDF) from the original on 29 September 2019. Retrieved 15 November 2020.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.