List of DIN standards

This is an incomplete list of DIN standards.

  • The "STATUS" column gives the latest known status of the standard.
    • If a standard has been withdrawn and no replacement specification is listed, either the specification was withdrawn without replacement or a replacement specification could not be identified.
  • DIN stands for "Deutsches Institut für Normung", meaning "German institute for standardisation". DIN standards that begin with "DIN V" ("Vornorm", meaning "pre-issue") are the result of standardization work, but because of certain reservations on the content or because of the divergent compared to a standard installation procedure of DIN, they are not yet published standards.

DIN 1 to DIN 999

DIN 1 to DIN 99
DIN Title Status DIN replacement Other org
replacement
DIN 1Cone Pins, untemperedWithdrawnDIN EN 22339ISO 2339
DIN 3Standard measurementsWithdrawn
DIN 5Technical drawings - Axonometric projections, Isometric projectionWithdrawnDIN ISO 5456-1, DIN ISO 5456-2,
DIN ISO 5456-3, DIN ISO 5456-4		ISO 5456-1, ISO 5456-2,
ISO 5456-3, ISO 5456-4
DIN 5-10Technical drawings - projections, termsWithdrawnDIN ISO 10209-2ISO 10209-2
DIN 6Projection displays in Normal, views and special presentationsWithdrawnDIN ISO 128, DIN EN ISO 128ISO 128
DIN 7Parallel PinsWithdrawnDIN EN ISO 2338ISO 2338
DIN 11Whitworth pipe threads 1/4"-6" Thread diameter, sizes, teaching informationWithdrawn
DIN 13-1ISO general purpose metric screw threads - Part 1: Nominal sizes for coarse pitch threads; nominal diameter from 1 mm to 68 mmActive
DIN 13-2ISO general purpose metric screw threads - Part 2: Nominal sizes for 0,2 mm, 0,25 mm and 0,35 mm fine pitch threads; nominal diameter from 1 mm to 50 mmActive
DIN 13-3ISO general purpose metric screw threads - Part 3: Nominal sizes for 0,5 mm fine pitch threads; nominal diameter from 3,5 mm to 90 mmActive
DIN 13-4ISO general purpose metric screw threads - Part 4: Nominal sizes for 0,75 mm fine pitch threads; nominal diameter from 5 mm to 110 mmActive
DIN 13-5ISO general purpose metric screw threads - Part 5: Nominal sizes for 1 mm and 1,25 mm fine pitch threads; nominal diameter from 7,5 mm to 200 mmActive
DIN 13-6ISO general purpose metric screw threads - Part 6: Nominal sizes for 1,5 mm fine pitch threads; nominal diameter from 12 mm to 300 mmActive
DIN 13-7ISO general purpose metric screw threads - Part 7: Nominal sizes for 2 mm fine pitch threads; nominal diameter from 17 mm to 300 mmActive
DIN 13-8ISO general purpose metric screw threads - Part 8: Nominal sizes for 3 mm fine pitch threads; nominal diameter from 28 mm to 300 mmActive
DIN 13-9ISO general purpose metric screw threads - Part 9: Nominal sizes for 4 mm fine pitch threads; nominal diameter from 40 mm to 300 mmActive
DIN 13-10ISO general purpose metric screw threads - Part 10: Nominal sizes for 6 mm fine pitch threads; nominal diameter from 70 mm to 500 mmActive
DIN 13-11ISO general purpose metric screw threads - Part 11: Nominal sizes for 8 mm fine pitch threads; nominal diameter from 130 mm to 1000 mmActive
DIN 13-12ISO general purpose metric screw threads - Part 12: 1 to 300 mm diameter coarse and fine pitch threads Selected diameters and pitchesActive
DIN 13-13ISO general purpose metric screw threads - Part 13: Selected sizes for screws, bolts and nuts from 1 to 52 mm screw thread diameter and limits of sizesActive
DIN 13-19ISO general purpose metric screw threads - Part 19: Nominal profilesActive
DIN 13-20ISO general purpose metric screw threads - Part 20: Limits of sizes for coarse pitch threads with the preferred tolerance classes; nominal sizes from 1 mm to 68 mmActive
DIN 13-21ISO general purpose metric screw threads - Part 21: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 1 mm to 24,5 mmActive
DIN 13-22ISO general purpose metric screw threads - Part 22: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 25 mm to 52 mmActive
DIN 13-23ISO general purpose metric screw threads - Part 23: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 53 mm to 110 mmActive
DIN 13-24ISO general purpose metric screw threads - Part 24: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 112 mm to 180 mmActive
DIN 13-25ISO general purpose metric screw threads - Part 25: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 182 mm to 250 mmActive
DIN 13-26ISO general purpose metric screw threads - Part 26: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 252 mm to 1000 mmActive
DIN 13-28ISO general purpose metric screw threads - Part 28: Coarse and Fine Screw Threads from 1 to 250 mm Screw Thread Diameter; Root Cross-sections, Tensile Stress Cross-sections and Pitch AnglesActive
DIN 13-50ISO general purpose metric screw threads - Part 50: Combination of tolerance classes for formed internal screw threadsActive
DIN 13-51ISO general purpose metric screw threads - Part 51: External screw threads for transition fits (former: screw threads for interference fit); tolerances, limit deviations, limits of sizesActive
DIN 13-52ISO general purpose metric screw threads - Part 52: Multi-start thread tolerances and deviation of profileActive
DIN 15-2 Technical drawings; lines; general application Withdrawn DIN ISO 128-24
DIN 16Oblique Standard Typeface for DrawingsWithdrawn
DIN 17Upright Standard Typeface for DrawingsWithdrawn
DIN 38 Plain bearings; bearing metal lining for thick-walled multilayer plain bearings Active
DIN 74 Countersinks for countersunk head screws (except screws with DIN EN 27721 head) Active
DIN 76-1Thread run-outs and thread undercuts for ISO metric threads in accordance with DIN 13-1Active
DIN 76-2Thread run-outs and thread undercuts for pipe threads conforming to ISO 228 part 1Active
DIN 76-3Runouts, Undercuts for Trapezoidal Threads, Buttress Threads and Knuckle Threads and other Threads of Coarse PitchActive
DIN 78Protrusions of bolt endsActiveDIN EN ISO 4753 (governs thread ends for bolts assembled with hexagon slotted nuts)ISO 4753
DIN 84Product grade A slotted cheese head screwsWithdrawnDIN EN ISO 1207ISO 1207
DIN 85Product grade A slotted pan head screwsWithdrawnDIN EN ISO 1580ISO 1580
DIN 88Product slotted oval head countersunk machine screwsWithdrawnISO 2010-1983[1]
DIN 93Tab washers with long tabWithdrawn
DIN 94Split pinsWithdrawnDIN EN ISO 1234ISO 1234
DIN 95Slotted Raised Countersunk (Oval) Head Wood ScrewsActive
DIN 96Slotted Round Head Wood ScrewsActive

DIN 100 to DIN 199
DIN Title Status DIN replacement Other org
replacement
DIN 101 Rivets - Technical specifications Active
DIN 103-1ISO Metric Trapezoidal Screw Thread; ProfilesActive
DIN 103-2ISO Metric Trapezoidal Screw Thread; General PlanActive
DIN 103-3ISO Metric Trapezoidal Screw Thread; Allowances and Tolerances for Trapezoidal Screw Threads of General PurposeActive
DIN 103-4ISO Metric Trapezoidal Screw Thread; Nominal DimensionsActive
DIN 103-5ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Nut Threads from 8 to 100 mm Nominal DiameterActive
DIN 103-6ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Nut Threads from 105 to 300 mm Nominal DiameterActive
DIN 103-7ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Bolt Threads from 8 to 100 mm Nominal DiameterActive
DIN 103-8ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Bolt Threads from 105 to 300 mm Nominal DiameterActive
DIN 103-9ISO metric trapezoidal screw threads; gauging of external and internal threads; gauge dimensions and design featuresActive
DIN V 105-1Clay masonry units - Part 1: Solid and hollow bricks with density classes of 1,2WithdrawnDIN V 105-100, DIN EN 771-1EN 771-1
DIN V 105-2Clay masonry units - Part 2: Solid and hollow bricks with density classes equal 1.0WithdrawnDIN V 105-100, DIN EN 771-1EN 771-1
DIN 105-3Clay masonry units - Part 3: Tile and high strength-high-strength clinkerWithdrawnDIN V 105-100, DIN EN 771-1EN 771-1
DIN 105-4Clay masonry units - Part 4: Ceramic bricksWithdrawnDIN V 105-100, DIN EN 771-1,
DIN EN 772-7		EN 771-1, EN 772-7
DIN 105-5Clay masonry units - Part 5: Lightweight long-hole brick and light long-hole brick panelsActive
DIN V 105-6Clay masonry units - Part 6: High precision unitsActive
DIN V 105-100Clay masonry units - Part 100: Clay masonry units with specific propertiesActive
DIN 125Washers; medium type, primarily for hexagon boltsWithdrawnDIN EN ISO 7089,
DIN EN ISO 7090		ISO 7089,
ISO 7090
DIN 125-1Product grade A washers - with a hardness up to 250 HV designed for use with hexagon head bolts and nutsWithdrawnDIN EN ISO 7089,
DIN EN ISO 7090		ISO 7089,
ISO 7090
DIN 125-2Product grade A washers - with a hardness up to 300 HV designed for use with hexagon head bolts and nutsWithdrawnDIN EN ISO 7089,
DIN EN ISO 7090		ISO 7089,
ISO 7090
DIN 126Product grade C washers - designed for use with hexagon head bolts and nutWithdrawnDIN EN ISO 7091ISO 7091
DIN 127Spring lock washers with square ends or tang endsWithdrawn
DIN 128Curved and wave spring lock washersWithdrawn
DIN 137Spring washers, curved or waveWithdrawnDIN EN 137
DIN 174 Bright Flat Steel; Dimensions, Permissible Variations, Weights Withdrawn DIN EN 10278
DIN 175 Polished round steel; Dimensions, Permissible deviations according to ISO tolerance zone h9 Withdrawn DIN EN 10278

DIN 200 to DIN 299
DIN Title Status DIN replacement Other org
replacement
DIN 201Technical drawings; Hatchings; Representation of cutting edges and materialsWithdrawnDIN ISO 128-50ISO 128-50
DIN 209Machine Reamers with Screwed-on BladesActive
DIN 267-1Fasteners - Part 1: Technical delivery conditions; General requirementsWithdrawnISO 8992
DIN 267-2Fasteners - Part 2: Technical delivery conditions; Bolts, Screws, Nuts and Similar Threaded and Formed Parts; Types and Dimensional AccuracyActiveDIN EN ISO 4759-1ISO 4759-1
DIN 267-3Fasteners - Part 3: Technical delivery conditions; Property classes for carbon steel and alloy steel bolts and screws; Conversion of property classesWithdrawnDIN EN ISO 898-1ISO 898-1
DIN 267-4Fasteners - Part 4: Technical delivery conditions; Property classes for nuts (previous classes)WithdrawnDIN EN ISO 898-2ISO 898-2
DIN 267-5Fasteners – Part 5: Technical delivery conditions; Acceptance inspection; modified version of ISO 3269, 1984 editionWithdrawnDIN EN ISO 3269ISO 3269
DIN 267-6Fasteners - Part 6: Technical delivery conditions; Designs and accuracy of measurement for product grade FActive
DIN 267-7Fasteners - Part 9: Technical delivery conditions; Bolts made of unalloyed or low-alloy steelsWithdrawnDIN EN ISO 898-1ISO 898-1
DIN 267-9Fasteners - Part 9: Technical delivery conditions; Components with Electroplated CoatingsWithdrawnDIN EN ISO 4042ISO 4042
DIN 267-10Fasteners - Part 10: Technical delivery conditions; Hot dip galvanized partsWithdrawnDIN EN ISO 10684ISO 10684
DIN 267-11Fasteners - Part 11: Technical delivery conditions (with additions to ISO 3506); Corrosion-resistant stainless steel fastenersWithdrawn
DIN 267-12Fasteners - Part 12: Technical delivery conditions; Self-tapping screwsWithdrawnDIN EN ISO 2702ISO 2702
DIN 267-13Fasteners - Part 13: Technical delivery conditions; Components for Bolted Connections Made Mainly from Materials Exhibiting a High Impact Strength at Low Temperature or from Materials with a High Temperature StrengthActive
DIN 267-15Fasteners - Part 15: Technical delivery conditions; Prevailing torque type nutsWithdrawnDIN EN ISO 2320,
DIN EN ISO 3506-1,
DIN EN ISO 3506-2,
DIN EN ISO 3506-3		ISO 2320,
ISO 3506-1,
ISO 3506-2,
ISO 3506-3
DIN 267-18Fasteners - Part 18: Technical delivery conditions; Components made of Non-ferrous MetalsWithdrawnDIN EN 28839ISO 8839
DIN 267-19Fasteners - Part 19: Technical delivery conditions; Surface discontinuities on bolts and screwsWithdrawnDIN EN ISO 26157-1,
DIN EN ISO 26157-3		ISO 6157-1,
ISO 6157-3
DIN 267-20Fasteners - Part 20: Technical delivery conditions; Surface discontinuities on nutsWithdrawnDIN EN ISO 6157-2,
DIN EN ISO 10484,
DIN EN ISO 10485		ISO 6157-2,
ISO 10484,
ISO 10485
DIN 267-21Fasteners - Part 21: Technical delivery conditions; Widening test on nutsWithdrawnDIN EN ISO 6157-2,
DIN EN ISO 10484,
DIN EN ISO 10485		ISO 6157-2,
ISO 10484,
ISO 10485
DIN 267-23Fasteners - Part 23: Technical delivery conditions; Property classes for nuts with fine thread (ISO classes)WithdrawnDIN EN ISO 898-6ISO 898-6
DIN 267-24Fasteners - Part 24: Technical delivery conditions; Property classes for nuts (Hardness classes)Active
DIN 267-25Fasteners - Part 25: Technical delivery conditions; Torsion testing of M1 to M10 bolts and screwsWithdrawnDIN EN 20898-7EN 20898-7
DIN 267-26Fasteners - Part 26: Technical delivery conditions; Conical spring washers for bolt/nut assembliesActive
DIN 267-27Fasteners - Part 27: Technical specifications; Steel screws, bolts and studs with adhesive coatingActive
DIN 267-28Fasteners - Part 28: Technical specifications; Steel screws, bolts and studs with locking coatingActive
DIN 267-29Fasteners - Part 29: Technical specifications; Product grades for parts for bolted connections for use at temperatures ranging from -200 °C to +700 °CWithdrawn
DIN 267-30Fasteners - Part 30: Technical specifications; Metric thread rolling screws of property class 10.9Active
DIN 276-1Building costs; Part 1: Building constructionActive
DIN 276-2Building costs; Part 2: Classification of costWithdrawn
DIN 276-3Building costs; Part 3: Ascertainment of costWithdrawn

DIN 300 to DIN 399
DIN Title Status DIN replacement Other org
replacement
DIN 315Wing nuts with rounded wingsActive
DIN 316Wing screws with rounded wingsActive
DIN 317Drill drifts for taper shanks with drift tangActive
DIN 323-1Preferred Numbers and Series of Preferred Numbers; Basic Values, Calculated Values, Rounded ValuesWithdrawn
DIN 323-2Preferred Numbers and Series of Preferred Numbers; IntroductionActive
DIN 332-160° centre holes; types R, A, B, and CActive
DIN 332-2Center holes 60° with thread for shaft ends for rotating electrical machinesActive
DIN 332-4Centre holes for rail vehicles axlesActive
DIN 332-7Machine tools; 60° centre holes; dimensioningActive
DIN 332-8Centre holes 90°, form S; dimensions, determination processActive
DIN 332-10Center Holes; Indications on Technical DrawingsWithdrawnDIN ISO 6411ISO 6411
DIN 338Parallel shank twist drills, jobber seriesActive
DIN 352Sets of taps - Sets of 3 taps for metric coarse ISO-threads M1 to M68Active
DIN 371Machine taps with reinforced shank for coarse pitch metric ISO-threads M1 to M10 and fine pitch metric ISO-threads M1 × 0,2 to M10 × 1,25Active
DIN 374Machine screwing taps for fine pitch metric ISO-threads M3 × 0,2 to M52 × 4Active

DIN 400 to DIN 499
DIN Title Status DIN replacement Other org
replacement
DIN 404Slotted capstan screwsActive
DIN 406-10Engineering drawing practice; dimensioning; concepts and general principlesActive
DIN 406-11Engineering drawing practice; dimensioning; principles of applicationActive
DIN 406-12Engineering drawing practice; dimensioning; tolerancing of linear and angular dimensions (modified version of ISO 406:1987)Active
DIN 417Slotted set screws with long dog pointWithdrawnDIN EN 27435ISO 7435
DIN 427Slotted headless screws with chamfered endWithdrawnDIN EN ISO 2342ISO 2342
DIN 428Hexagon nuts, Grade CWithdrawnDIN EN ISO 4034ISO 4034
DIN 433Washers for use with cheese head screwsWithdrawnDIN EN ISO 7092ISO 7092
DIN 433-1Product grade A washers - with a hardness up to 250 HV designed for use with cheese head screwsWithdrawnDIN EN ISO 7092ISO 7092
DIN 433-2Product grade A washers - with a hardness up to 300 HV designed for use with cheese head screwsWithdrawnDIN EN ISO 7092ISO 7092
DIN 438Slotted set screws with cup pointWithdrawnDIN EN 27436ISO 7436
DIN 439Hexagon thin nutsWithdrawnDIN EN ISO 4035, DIN EN ISO 4036, DIN EN ISO 8675ISO 4035, ISO 4036,
ISO 8675
DIN 439-1Unchamfered hexagon thin nuts - Product grade BWithdrawnDIN EN ISO 4036ISO 4036
DIN 439-2Chamfered hexagon thin nuts - Product grades A and BWithdrawnDIN EN ISO 4035, DIN EN ISO 8675ISO 4035, ISO 8675
DIN 440Washers for use in timber constructionsWithdrawnDIN EN ISO 7094ISO 7094
DIN 444EyeboltsActive
DIN 461Graphical Representation in Systems of CoordinatesActive
DIN 462Machine Tools; Internal Tab Washers for Slotted Round Nuts for Hook Spanner according to DIN 1804Active
DIN 464Knurled thumb screws, high typeActive
DIN 466Knurled nuts, high typeActive
DIN 467Knurled nuts, low typeActive
DIN 471Circlips (retaining rings) for shafts; Normal type and heavy typeActive
DIN 472Circlips (retaining rings) for internal grooves; Normal type and heavy typeActive
DIN 476Paper sizesWithdrawnDIN EN ISO 216ISO 216
DIN 476-2Trimmed Sizes of Paper - C SeriesActive
DIN 477-1Gas cylinder valves for cylinder test pressures up to 300 bar - Part 1: Valve inlet and outlet connectionsActive
DIN 479Square head bolts with short dog pointActive

DIN 500 to DIN 599
DIN Title Status DIN replacement Other org
replacement
DIN 522Metal washers; technical delivery conditionsWithdrawnDIN EN ISO 4759-3ISO 4759-3
DIN 548Round nuts with set pin holes in sideActive
DIN 551Slotted set screws with flat pointWithdrawnDIN EN 24766ISO 4766
DIN 553Slotted set screws with cone pointWithdrawnDIN EN 27434ISO 7434
DIN 555M5 to M100x6 hexagon nuts - Product grade CWithdrawnDIN EN ISO 4034ISO 4034
DIN 558Hexagon head screwsWithdrawnDIN EN ISO 4018ISO 4018
DIN 580Collar eyebolts for lifting purposesActive

DIN 600 to DIN 699
DIN Title Status DIN replacement Other org
replacement
DIN 601M5 to M52 hexagon head bolts; product grade CWithdrawnDIN EN ISO 4016ISO 4016
DIN 603Mushroom head square neck boltsActive
DIN 609Hexagon fits bolts with long threadActive
DIN 625-1Rolling bearings; single row radial contact ball bearingsActive
DIN 625-3Rolling bearings; double row radial contact ball bearingsActive
DIN 625-4Rolling bearings; radial contact groove ball bearings with flanged outer ringActive
DIN 653Knurled thumb screws, low typeActive
DIN 678-1Envelopes - Part 1: SizesActive
DIN 678-2Envelopes - Part 2: Envelopes for Processing in Enveloping Machines, Size C6 to C4Active

DIN 700 to DIN 799
DIN Title Status DIN replacement Other org
replacement
DIN 763Tested, non-calibrated, long-link round steel chainsActive
DIN 764-1Calibrated and tested round steel link chains for continuous conveyors; grade 2, pitch 3,5dActive
DIN 764-2Calibrated and tested round steel link chains for continuous conveyors; grade 3, pitch 3,5dActive
DIN 766Calibrated and tested grade 3 round steel link chainsActive
DIN 799-1Foundation BlocksActive

DIN 800 to DIN 899
DIN Title Status DIN replacement Other org
replacement
DIN 820-1Standards Work - Part 1: PrinciplesActive
DIN 820-2Standardization - Part 2: Presentation of standards; examples for presentation of figures, tables and part listsActive
DIN 820-3Standardization - Pdfart 3: ConceptsActive
DIN 820-4Standardization - Part 4: Working procedureActive
DIN 820-11Standardization - Part 11: Presentation of Standards concerning safety regulations which are VDE-Specifications or VDE-GuidelinesActive
DIN 820-12Standardization - Part 12: Presentation of standards concerning safety regulationsActive
DIN 820-13Standardization - Part 13: Adoption of European documents of CEN, CENELEC and of ETSI; Concepts and presentationActive
DIN 820-15Standardization - Part 15: Implementation of ISO and IEC international documents; Concepts and presentationActive
DIN 820-120Standardization - Part 120: Guidelines for the inclusion of safety aspects in standards (ISO/IEC Guide 51:1999)Active
DIN 824Technical drawings; Folding to filing sizeActive
DIN 899Hand Operated Wrenches and Sockets; Technical SpecificationsWithdrawnDIN ISO 1711-1ISO 1711-1

DIN 900 to DIN 999
DIN Title Status DIN replacement Other org
replacement
DIN 906internal drive pipe plugs for the sealing of holes with cylindrical internal threadsActive
DIN 908Hexagon socket screw plugs with parallel screw threadActive
DIN 910Hexagon-duty hexagon head screw plugsActive
DIN 911Hexagon Socket Screw KeysWithdrawnDIN ISO 2936ISO 2936
DIN 912Hexagon socket head cap screws (modified version of ISO 4762)WithdrawnDIN EN ISO 4762,
DIN EN ISO 21269		ISO 4762,
ISO 21269
DIN 913Hexagon socket set screws with flat point (ISO 4026 modified)WithdrawnDIN EN ISO 4026ISO 4026
DIN 914Hexagon socket set screws with cone point (ISO 4027 modified)WithdrawnDIN EN ISO 4027ISO 4027
DIN 915Hexagon socket set screws with full dog pointt (ISO 4028 modified)WithdrawnDIN EN ISO 4028ISO 4028
DIN 916Hexagon socket set screws with cup point (ISO 4029 modified)WithdrawnDIN EN ISO 4029ISO 4029
DIN 918Fasteners; Terminology; Spelling of terms; AbbreviationsActive
DIN 918-3Overview of European Standards for fastenersActive
DIN 919-1Technical Drawings; Wood Processing; PrinciplesActive
DIN 921Slotted pan head screws with large headActive
DIN 923Slotted pan head screws with shoulderActive
DIN 929Hexagon weld nutsActive
DIN 930Fine thread pitch partially threaded screwsWithdrawnDIN 931-1, DIN 931-2
DIN 931-1M1,6 to M39 Hexagon Cap Screws Partially Threaded - Product grades A and BWithdrawnDIN EN ISO 4014ISO 4014
DIN 931-2M42 to M160x6 Hexagon Cap Screws Partially Threaded - Product grade BWithdrawnDIN EN ISO 4014ISO 4014
DIN 933M1,6 to M52 Hexagon Cap Screws Fully Threaded - Product grades 8.8WithdrawnDIN EN ISO 4017ISO 4017
DIN 934Hexagon nuts with metric coarse and fine pitch thread - Product classes A and BWithdrawnDIN EN ISO 4032,
DIN EN ISO 8673		ISO 4032,
ISO 8673
DIN 935-1Hexagon slotted nuts and castle nuts with metric coarse and fine pitch thread - Product grades A and BActive
DIN 935-2M42 to M160x6 hexagon head bolts; product grade BActive
DIN 935-3Hexagon slotted nuts with metric coarse pitch thread - Product grade CActive
DIN 936M8 to M52 and M8x1 to M52x3 hexagon thin nuts; product grades A and BWithdrawn
DIN 937Hexagon thin castle nutsWithdrawn
DIN 938Studs with a length of engagement equal to about 1 dActive
DIN 939Studs with a length of engagement equal to about 1,25 dActive
DIN 946Determination of coefficient of friction of bolt/nut assemblies under specified conditionsWithdrawnDIN EN ISO 16047ISO 16047
DIN 960M8x1 to M100x4 hexagon head bolts with fine pitch thread - Product grades A and BWithdrawnDIN EN ISO 8765,
DIN EN ISO 8676		ISO 8765,
ISO 8676
DIN 961M8x1 to M52x3 hexagon head bolts with fine pitch thread - Product grades A and BWithdrawnDIN EN ISO 8676ISO 8676
DIN 962Designation system for fastenersActive
DIN 963Slotted countersunk head screws (with countersunk heads as specified in ISO 2009-1972)WithdrawnDIN EN ISO 2009ISO 2009
DIN 964Slotted raised countersunk oval head screwsWithdrawnDIN EN ISO 2010ISO 2010
DIN 965Cross recessed countersunk flat head screwsWithdrawnDIN EN ISO 7046-1,
DIN EN ISO 7046-2		ISO 7046-1,
ISO 7046-2
DIN 966Cross recessed raised countersunk head screwsWithdrawnDIN EN ISO 7047ISO 7047
DIN 970Hexagon nuts; Style 1; Metric coarse thread, Product grades A and B; ISO 4032 modifiedWithdrawnDIN EN ISO 4032ISO 4032
DIN 971-1Style 1 hexagon nuts with metric fine pitch thread; property classes 6 and 8WithdrawnDIN EN ISO 8673ISO 8673
DIN 971-2Style 2 hexagon nuts with metric fine pitch thread; property classes 10 and 12WithdrawnDIN EN ISO 8674ISO 8674
DIN 972M5 to M39 hexagon nuts; style 1; product grade C (modified version of ISO 4034)WithdrawnDIN EN ISO 4034ISO 4034
DIN 975Threaded rodsWithdrawnDIN 976-1, DIN 976-2
DIN 976-1Metric thread stud boltsActive
DIN 976-2Metric interference-fit thread stud boltsActive
DIN 977Hexagon weld nuts with flangeWithdrawnDIN EN ISO 21670ISO 21670
DIN 979Hexagon thin slotted nuts and castle nuts with metric coarse and fine pitch thread - Product grades A and BActive
DIN 980All-metal prevailing torque type hexagon nutsWithdrawnDIN EN ISO 7042,
DIN EN ISO 10513		ISO 7042,
ISO 10513
DIN 981Locknuts for use with rolling bearingsActive
DIN 982Prevailing torque type hexagon nuts with nonmetallic insertWithdrawnDIN EN ISO 7040,
DIN EN ISO 10512		ISO 7040,
ISO 10512
DIN 983Retaining rings with lugs for use on shafts (external circlips)Active
DIN 985Prevailing torque type hexagon thin nuts with nonmetallic insertWithdrawnDIN EN ISO 10511ISO 10511
DIN 986Prevailing torque type hexagon domed cap nuts with non-metallic insertActive
DIN 988Shim rings and supporting ringsActive

DIN 1000 to DIN 9999

DIN 1000 to DIN 1999
DIN Title Status DIN replacement Other org
replacement
DIN 1025-1Hot rolled I-sections - Part 1: Narrow flange I-sections, I-serie - Dimensions, masses, sectional propertiesActive
DIN 1025-2Hot rolled I-beams - Part 2: Wide flange I-beams, IPB-serie; dimensions, masses, sectional propertiesActive
DIN 1025-3Hot rolled I-beams; wide flange I-beams, light pattern, IPBl-serie; dimensions, masses, sectional propertiesActive
DIN 1025-4Hot rolled I-beams; wide flange I-beams heavy pattern, IPBv-serie; dimensions, masses, sectional propertiesActive
DIN 1025-5Hot rolled I-beams; medium flange I-beams, IPE-serie; dimensions, masses, sectional propertiesActive
DIN 1301-1Units - Part 1: Names and SymbolsActive
DIN 1301-2Units - Part 2: Submultiples and Multiples for General UseActive
DIN 1301-3Units - Part 3: Conversions of Units No Longer To Be UsedActive
DIN 1302General Mathematical Symbols and ConceptsActive
DIN 1303Vectors, matrices, tensors; symbols and conceptsActive
DIN 1304-1Letter symbols for physical quantities - Part 1: Symbols for general useActive
DIN 1304-2Letter symbols for physical quantities - Part 2: Symbols for use in meteorology and geophysicsActive
DIN 1304-3Letter symbols for physical quantities - Part 3: Symbols for use in electric power engineeringActive
DIN 1304-5Letter symbols for physical quantities - Part 5: Symbols for use in fluid mechanicsActive
DIN 1304-8Letter symbols for physical quantities - Part 9: Symbols for use in the field of static converters using semiconductor devicesActive
DIN 1304-9Letter symbols for physical quantities - Part 9: Symbols for equivalent circuits of piezoelectric crystalsActive
DIN 1311-1(Mechanical) vibrations, oscillations and vibration systems - Part 1: Basic concepts, surveyActive
DIN 1311-2(Mechanical) vibrations, oscillations and vibration systems - Part 2: Linear vibration systems with single degree of freedomActive
DIN 1311-3(Mechanical) vibrations, oscillations and vibration systems - Part 3: Linear time-invariant vibration systems with a finite number of degrees of freedomActive
DIN 1311-4Vibration; Vibrating Continua, WavesActive
DIN 1313Physical Quantities and Equation; Concepts, Methods of WritingActive
DIN 1315Angle; Concepts, UnitsActive
DIN 1318Loudness LevelActive
DIN 1319-1Fundamentals of Metrology – Part 1: Basic TerminologyActive
DIN 1319-2Basic Concepts in Metrology – Part 2: Terminology Related To Measuring EquipmentActive
DIN 1319-3Basic Concepts in Metrology – Part 3: Terminology Relating To the Uncertainty of Measurement and the Assessment of Measuring Instruments and Measuring EquipmentActive
DIN 1319-4Basic Concepts in Metrology – Part 4: Treatment of Uncertainties in the Evaluation of MeasurementsActive
DIN 1320Acoustics; TerminologyActive
DIN 1324-1Electromagnetic Field - Part 1. State QuantitiesActive
DIN 1324-2Electromagnetic Field - Part 2. Material QuantitiesActive
DIN 1324-3Electromagnetic Field - Part 3. Electromagnetic WavesActive
DIN 1325-1Vocabulary for value management, value analysis and functional analysis - Part 1: Value analysis and functional analysisActive
DIN 1325-2Value Management, Value Analysis, Functional Analysis Vocabulary - Part 2: Value ManagementActive
DIN 1332Acoustics; SymbolsWithdrawnDIN EN ISO 80000-8ISO 80000-8
DIN 1333Presentation of Numerical DataActive
DIN 1338Writing and Typesetting of FormulaeActive
DIN 1355-1Time; Calendar, Numbering of Weeks, Date of Day, (Clock) TimeWithdrawn
DIN 1421Arrangement and Numbering in Texts; Clauses, Paragraphs, EnumerationsActive
DIN 1422-1Publications in Sciences, Technology, Economy and Administration; Presentation of Manuscripts and TyposcriptsActive
DIN 1422-2Publications in Sciences, Technology, Economy and Administration; Presentation of Clean Copies for Reprographic UseActive
DIN 1422-3Publications in Sciences, Technology, Economy and Administration; Typographical PresentationActive
DIN 1422-4Publications in Sciences, Technology, Economy and Administration; Presentation of Scientific and Technical ReportsActive
DIN 1440Medium type washers for pinsWithdrawnDIN EN 28738ISO 8738
DIN 1443Clevis pins without headWithdrawnDIN EN 22340ISO 2340
DIN 1444Clevis pins with headWithdrawnDIN EN 22341ISO 2341
DIN 1450Legibility of Typefaces – GeneralActive
DIN 1451-1Lettering - Linear-Antiqua without serifes – GeneralActive
DIN 1451-2Typefaces - lineal Linear-Antiqua; lettering for transportationActive
DIN 1451-3Lettering - Linear-Antiqua without serifes; lettering for printingActive
DIN 1451-4Typefaces - lineal Linear-Antiqua; stenciled lettering for engraving and other processesActive
DIN 1463-1Guidelines for the Establishment and Development of Thesauri; Monolingual ThesauriActive
DIN 1463-2Guidelines for the Establishment and Development of Thesauri; Multilingual ThesauriActive
DIN 1470Grooved Pins, Full Length Parallel-grooved with PilotWithdrawnDIN EN 8739ISO 8739
DIN 1471Grooved Pins, Full Length Taper-groovedWithdrawnDIN EN 8744ISO 8744
DIN 1472Grooved Pins, Half Length Taper-groovedWithdrawnDIN EN 8745ISO 8745
DIN 1473Grooved Pins, Full Length Parallel-grooved with ChamferWithdrawnDIN EN ISO 8740ISO 8740
DIN 1474Grooved Pins, Half Length Reverse-groovedWithdrawnDIN EN 8741ISO 8741
DIN 1475Grooved Pins, Third Length Centre-groovedWithdrawnDIN EN 8742ISO 8742
DIN 1476Round Head Grooved PinsWithdrawnDIN EN 8746ISO 8746
DIN 1477Countersunk Head Grooved PinsWithdrawnDIN EN 8747ISO 8747
DIN 1481Spring-Type Straight Pins (Roll Pins) - Heavy TypeWithdrawnDIN EN ISO 8752ISO 8752
DIN 1505-1Bibliographic references to documents - Part 1: Full References to Printed and Published DocumentsActive
DIN 1505-2Bibliographic references to documents - Part 2: Rules for CitingActive
DIN 1505-3Bibliographic references to documents - Part 3: Indexes of cited documents (bibliographies)Active
DIN 1511Pattern Equipment for Foundries; Production and QualityWithdrawnDIN EN 12890EN 12890
DIN 1530-1Tools for moulding - Part 1: Ejector pins with cylindrical headActive
DIN 1530-2Tools for moulding - Part 2: Shouldered ejector pinsActive
DIN 1530-3Tools for moulding - Part 3: Ejector pins with conical headActive
DIN 1587Hexagon domed cap nutsActive
DIN 1707Soft Solders; Composition, Technical Delivery ConditionActiveDIN EN ISO 9453ISO 9453
DIN 1712 Part 1Aluminium and aluminium alloys - Unalloyed aluminium ingots for remelting – SpecificationsWithdrawnDIN EN 576EN 576
DIN 1712 Part 3Aluminium; Half-Finished ProductsWithdrawnDIN EN 573-3EN 573-3
DIN 1783Strips, Plates and Sheets of Aluminium and WroughtWithdrawnDIN EN 485-4EN 485-4
DIN 1786Seamless Drawn Copper Tubes for Piping SystemsWithdrawnDIN EN 1057EN 1057
DIN 1798Round Rod of Aluminium (Highest Grade Aluminium)WithdrawnDIN EN 754-3EN 754-3
DIN 1804Slotted Round Nut for Hook Spanner; ISO Metric Fine ThreadActive
DIN 1810Hook wrenchesActive
DIN 1816Round Nut with Set Pin Holes Inside; ISO Metric Fine ThreadActive
DIN 1912-1Graphical Representation of Welded, Soldered and Brazed JointsWithdrawnDIN EN ISO 17659ISO 17659
DIN 1912-2Graphical Representation of Welded, Soldered and Brazed JointsWithdrawnDIN EN ISO 6947ISO 6947
DIN 1912-4Graphical Representation of Welded, Soldered and Brazed Joints; Concepts and Terms for Soldered and Brazed Joints and SeamsActive
DIN 1912-5Symbolic Representation on Drawings of Welded, Soldered and Brazed JointsWithdrawnDIN EN 22553ISO 2553
DIN 1960Construction contract procedures (VOB) - Part A: General provisions relating to the award of construction contractsActive
DIN 1961Construction contract procedures (VOB) - Part B: General conditions of contract relating to the execution of construction workActive

DIN 2000 to DIN 2999
DIN Title Status DIN replacement Other org
replacement
DIN 2112Alphanumeric office machines - Alphanumeric keyboards, keyboard arrangement for manually operated typewritersWithdrawnDIN 2137-1, DIN 2137-2
DIN 2127Alphanumeric office machines; alphanumeric keyboards, keyboard arrangement for electro-mechanical operated typewritersWithdrawnDIN 2137-1, DIN 2137-2
DIN 2137-1Keyboards for data and text input - Part 1: German keyboard layoutActive
DIN 2137-2Keyboards for data and text input - Part 2: Additional requirementsActive
DIN 2181Sets of 2 taps for metric fine ISO-threads M1 × 0,2 to M52 × 4Active
DIN 2342-1Vocabulary of terminology; basic conceptsActive
DIN 2391-1Seamless precision steel tubes - Part 1: DimensionsCanceledDIN EN 10305-1EN 10305-1
DIN 2391-2Seamless precision steel tubes - Part 2: Technical delivery conditionsCanceledDIN EN 10305-1EN 10305-1
DIN 2448Seamless Steel Pipes and Tubes - Dimensions, Conventional Masses per Unit LengthCanceledDIN EN 10220EN 10220
DIN 2527Blank flanges - Nominal pressure 6 to 100WithdrawnDIN EN 1092-1EN 1092-1
DIN 2860Capillary Fittings; Bends 180° of CopperWithdrawn
DIN 2999-1Pipe threads for tubes and fittings; parallel internal thread and taper external thread; tread dimensionsWithdrawnDIN EN 10226-1EN 10226-1
DIN 2999-2Whitworth Pipe Threads for Tubes and Fittings; Cylindrical Internal Thread and Conical External Thread, Gauging System and Use of GaugesWithdrawnDIN EN 10226-3EN 10226-3
DIN 2999-3Whitworth Pipe Threads for Tubes and Fittings; Gauge DimensionsWithdrawnDIN EN 10226-3EN 10226-3
DIN 2999-4Pipe threads for tubes and fittings; sizes for taper screw limit plug gauges for parallel internal threadWithdrawnDIN EN 10226-3EN 10226-3
DIN 2999-5Whitworth Pipe Threads for Tubes and Fittings; Cylindrical Screw Limit Ring Gauges for Gauging Conical External Threads, SizesWithdrawnDIN EN 10226-3EN 10226-3
DIN 2999-6Whitworth Pipe Threads for Tubes and Fittings; Conical Screw Check Plugs, SizesWithdrawnDIN EN 10226-3EN 10226-3

DIN 3000 to DIN 3999
DIN Title Status DIN replacement Other org
replacement
DIN 3000,
DIN 3017-1Hose clamps with worm gear drive; shape A,
DIN 3017-2Hose clamps - Part 2: Clamps with fastening lugs,
DIN 3017-3Hose clamps - Part 3: Bolt clamps,
DIN 3017-4Hose clamps - Part 4: Technical delivery conditions,
DIN 3017-5Hose clamps - Part 5: Wide strip hose clamps with fastening lugs; Types D and E,
DIN 3770Sealing rings ("O-rings") with special accuracy, made of elastomeric materialsWithdrawn
DIN 3771-3Fluid systems; O-rings; materials, field of applicationActive

DIN 4000 to DIN 4999
DIN Title Status DIN replacement Other org
replacement
DIN 4048-1Water engineering, terms - Part 1: Dam plantsActive
DIN 4048-2Water engineering, terms - Part 2: Waterpower plantsActive
DIN 4054Correction of waterways, termsActive
DIN 4094-1Subsoil, Field investigations - Part 1: Cone penetration testsActive
DIN 4102-1Fire behaviour of building materials and elements - Part 1: Classification of building materials - Requirements and testingActive
DIN 4102-2Fire Behaviour of Building Materials and Building Components - Part 2: Building Components; Definitions, Requirements and TestsActive
DIN 4102-3Fire Behaviour of Building Materials and Building Components - Part 3: Fire Walls and Non-load-bearing External Walls; Definitions, Requirements and TestsActive
DIN 4102-4Fire behaviour of building materials and elements - Part 4: Overview and design of classified building materials, elements and componentsActive
DIN 4102-5Fire Behaviour of Building Materials and Building Components - Part 5: Fire Barriers, Barriers in Lift Wells and Glazings Resistant against Fire; Definitions, Requirements and TestsActive
DIN 4102-6Fire Behaviour of Building Materials and Building Components - Part 6: Ventilation Ducts; Definitions, Requirements and TestsActive
DIN 4102-7Fire behaviour of building materials and elements - Part 7: Roofing - Concepts, requirements and testingActive
DIN 4102-8Fire behaviour of building materials and components - Part 8: Small-scale test furnaceActive
DIN 4102-9Fire behaviour of building materials and elements - Part 9: seals for cable penetrations; concepts, requirements and testingActive
DIN 4102-11Fire behaviour of building materials and building components - Part 10: pipe encasements, pipe bushings, service shafts and ducts, and barriers across inspection openings; terminology, requirements and testingActive
DIN 4102-12Fire behaviour of building materials and elements - Part 12: Fire resistance of electric cable systems required to maintain circuit integrity - Requirements and testingActive
DIN 4102-13Fire behaviour of building materials and elements - Part 13: Fire resistant glazing; concepts, requirements and testingActive
DIN 4102-14Fire behaviour of building materials and elements - Part 14: Determination of the burning behaviour of floor covering systems using a radiant heat sourceActive
DIN 4102-15Fire behaviour of building materials and elements - Part 15: "Brandschacht"Active
DIN 4102-16Fire behaviour of building materials and elements - Part 16: "Brandschacht" testsActive
DIN 4102-17Fire behaviour of building materials and elements - Part 17: determination of melting point of mineral fibre insulating materials; concepts, requirements and testingActive
DIN 4102-18Fire behaviour of building materials and components - Part 18: fire barriers, verification of automatic closure (continuous performance test)Active
DIN 4102-22Fire behaviour of building materials and building components - Part 22: Application standard for DIN 4102-4 based on the design of partial safety factorsActive
DIN 4108-1Thermal protection and energy economy in buildings - Part 1: Quantities and unitsActive
DIN 4108-2Thermal protection and energy economy in buildings - Part 2: Minimum requirements to thermal insulationActive
DIN 4108-3Thermal protection and energy economy in buildings - Part 3: Protection against moisture subject to climate conditions; Requirements and directions for design and constructionActive
DIN 4108-7Thermal insulation and energy economy of buildings - Part 7: Airtightness of building, requirements, recommendations and examples for planning and performanceActive
DIN 4108-10Thermal insulation and energy economy in buildings - Part 10: Application-related requirements for thermal insulation materials - Factory made productsActive
DIN 4150-1Structural vibration - Part 1: Prediction of vibration parametersActive
DIN 4150-2Structural vibration - Part 2: Human exposure to vibration in buildingsActive
DIN 4150-3Structural vibration - Part 3: Effects of vibration on structuresActive
DIN 4420-1Service and working scaffolds - Part 1: Service scaffolds - Performance requirements, general design, structural designActive
DIN 4512Photographic sensitometry, determination of optical density: "Photographische Sensitometrie, Bestimmung der optischen Dichte" (1934-01, 1957-11, 1961-10)WithdrawnDIN 4512-1:1971-04, DIN 4512-3:1973-01, DIN 4512-4:1977-06, DIN 4512-5:1977-10, DIN 4512-6:1980-07
DIN 4512-1Photographic sensitometry, determination of the speed of black and white negative materials for pictorial photography (1971-04, 1993-05)Withdrawn (2000–09)DIN ISO 6:1996-02ISO 6
DIN 4512-3Photographic sensitometry, determination of diffuse transmission density (1973-01)WithdrawnDIN 4512-7:1993-01, DIN 4512-8:1993-01, DIN 4512-9:1993-01
DIN 4512-4Photographic sensitometry; determination of the speed of colour reversal films (1977-06, 1985-08)Withdrawn (2002–06)DIN ISO 2240:1998-06ISO 2240
DIN 4512-5Photographic sensitometry; determination of the speed of colour negative films (1977-10, 1990-11)Withdrawn (2002–06)DIN ISO 5800:1998-06ISO 5800
DIN 4512-6Photographic sensitometry; sensitometric illuminants and light sources (1980-07)Withdrawn
DIN 4512-7Photographic sensitometry, determination of optical density; concepts, symbols and notations (1993-01)Active
DIN 4512-8Photographic sensitometry, determination of optical density; geometric conditions for transmission density (1993-01)Active
DIN 4512-9Photographic sensitometry, determination of optical density; spectral conditions (1993-01)Active
DIN 4512-10Photographic sensitometry, determination of optical density; geometric conditions for reflection density (1993-01)Active
DIN V 4701-10Energy efficiency of heating and ventilation systems in buildings - Part 10: Heating, domestic hot water supply, ventilationActive
DIN V 4701-12Energetic evaluation of heating and ventilation systems in existing buildings - Part 12: Heat generation and domestic hot water generationActive
DIN 4710Statistics on German meteorological data for calculating the energy requirements for heating and air conditioning equipmentActive

DIN 5000 to DIN 5999
DIN Title Status DIN replacement Other org
replacement
DIN 5008Rules for text presentationActive
DIN 5031-1Physics of radiation in the field of optics and illuminating engineering - Part 1: Quantities, symbols and units of radiation physicsActive
DIN 5031-2Physics of radiation in the field of optics and illuminating engineering - Part 2: Evaluation of radiation by different detectorsActive
DIN 5031-3Physics of radiation in the field of optics and illuminating engineering - Part 3: Quantities, symbols and units of illuminating engineeringActive
DIN 5031-4Physics of radiation in the field of optics and illuminating engineering - Part 4: EfficienciesActive
DIN 5031-5Physics of radiation in the field of optics and illuminating engineering - Part 5: Definitions for temperaturesActive
DIN 5031-6Physics of radiation in the field of optics and illuminating engineering - Part 6: Pupil intensity as a measure of retinal illuminationActive
DIN 5031-7Physics of radiation in the field of optics and illuminating engineering - Part 7: Terms for wavebandsActive
DIN 5031-8Physics of radiation in the field of optics and illuminating engineering - Part 8: Definitions and constants of radiation physicsActive
DIN 5031-9Physics of radiation in the field of optics and illuminating engineering - Part 9: Definitions in the field of luminescenceActive
DIN 5031-10Physics of radiation in the field of optics and illuminating engineering - Part 10: Photobiologically effective radiation, quantities, symbols and actionsActive
DIN 5035-3Artificial lighting - Part 3: Lighting of health care premisesActive
DIN 5035-6Artificial lighting - Part 6: Measurement and evaluationActive
DIN 5035-7Artificial lighting - Part 7: Lighting of interiors with visual displays work stationsActive
DIN 5035-8Artificial lighting - Part 8: Workplace luminaries - Requirements, recommendations and proofingActive
DIN 5117Clamp strength for woodworkingActive
DIN 5145Plane irons for wood smooth and for planesActive
DIN 5146Curved irons for jack planesActive
DIN 5406Lockwashers and locking plates for use with rolling bearingsActive
DIN 5466-1Splined joints, calculation of load capacity - Part 1: general basisActive
DIN 5473Logic and set theory; symbols and conceptsActive
DIN 5474Signs in mathematical logicWithdrawnDIN 5473
DIN 5475-1Complex quantities; nomenclatureWithdrawnDIN 5483-3
DIN 5480-1Involute splines based on reference diameters - Part 1: GeneralitiesActive
DIN 5480-2Involute splines based on reference diameters - Part 2: Nominal and inspection dimensionsActive
DIN 5480-15Involute splines based on reference diameters - Part 15: InspectionActive
DIN 5483-1Time-dependent quantities - Part 1: Terms for the time-dependencyActive
DIN 5483-2Time-dependent quantities - Part 2: Letter symbolsActive
DIN 5483-3Time-dependent quantities - Part 3: Complex representation of sinusoidal time-dependent quantitiesActive
DIN 5486Notation of matricesWithdrawnDIN 1303
DIN 5487Fourier-, Laplace- and Z-transformation; symbols and conceptsActive
DIN 5489Directions and signs in electrical engineering; rules for electric and magnetic circuits, equivalent circuit diagramsWithdrawnDIN EN 60375EN 60375
DIN 5493-2Logarithmic quantities and units - Part 2: Logarithmic ratios, levels in nepers and decibelsActive
DIN 5510-2Fire test to railway componentsActive
DIN 5590Compressed air equipment for rail vehicles - Pressure vessels made of steel - Dimensions, designationActive

DIN 6000 to DIN 6999
DIN Title Status DIN replacement Other org
replacement
DIN 6319Spherical washers and conical seatsActive
DIN 6325Parallel Pins, Hardened; Tolerance Zone m6WithdrawnDIN EN ISO 8734ISO 8734
DIN 6340Washers for clamping devicesActive
DIN 6738Paper and paper board - Lifespan classesActive
DIN 6776Technical drawings, labelingWithdrawnDIN EN ISO 3098ISO 3098
DIN 6796 Conical spring washers for bolted connections Active
DIN 6797Toothed lock washersWithdrawn
DIN 6798Serrated lock washersWithdrawn
DIN 6799Lock washers (retaining washers) for shaftsActive
DIN 6880Bright Key Steel; Dimensions, Permissible Variations, WeightsActive
DIN 6885-1Drive Type Fastenings without Taper Action – Part 1: Parallel Keys, Keyways, Deep PatternActive
DIN 6885-2Drive Type Fastenings without Taper Action – Part 2: Parallel Keys, Keyways, Deep Pattern for Machine Tools, Dimensions and ApplicationActive
DIN 6885-3Drive Type Fastenings without Taper Action – Part 3: Parallel Keys, Shallow Pattern, Dimensions and ApplicationActive
DIN 6900Screw and Washer AssembliesWithdrawnDIN EN 10644EN 10644
DIN 6901Tapping screw and washer assembliesWithdrawnDIN EN 10510EN 10510
DIN 6902Plain washers for screw and washer assembliesWithdrawnDIN EN 10673EN 10673
DIN 6903Plain washers for tapping screw and washer assembliesWithdrawnDIN EN 10669EN 10669
DIN 6912Hexagon socket head cap screws with center, with low headActive
DIN 6914High-strength hexagon head bolts with large widths across flats for structural steel boltingWithdrawnDIN EN 14399-4EN 14399-4
DIN 6915Steel hexagon nuts with large widths across flats for high-strength structural boltingWithdrawnDIN EN 14399-4EN 14399-4
DIN 6916Round washers for high-strength structural steel boltingWithdrawnDIN EN 14399-6EN 14399-6
DIN 6921Hexagon flange boltsWithdrawnDIN EN 1665EN 1665
DIN 6922Hexagon flange bolts with reduced shankWithdrawnDIN EN 1665EN 1665
DIN 6923Hexagon nuts with flangeWithdrawnDIN EN 1661EN 1661
DIN 6924Prevailing torque type hexagon nuts with nonmetallic insertWithdrawnDIN EN ISO 7040,
DIN EN ISO 10512		ISO 7040,
ISO 10512
DIN 6925Prevailing torque type all-metal hexagon nutsWithdrawnDIN EN ISO 7042,
DIN EN ISO 10513		ISO 7042,
ISO 10513
DIN 6926Prevailing torque type hexagon nuts with flange and with non-metallic insertWithdrawnDIN EN 1663, DIN EN 1666ISO 7043 (modified), ISO 12125 (modified)
DIN 6927Prevailing torque type all-metal nuts with flangeWithdrawnDIN EN 1664, DIN EN 1667ISO 7044 (modified),
ISO 12126 (modified)
DIN 6935Cold bending of flat rolled steelActive

DIN 7000 to DIN 7999
DIN Title Status DIN replacement Other org
replacement
DIN 7045Pan head screws with type H or type Z cross recess - product grade AActive
DIN 7245Saw blades for web sawsActive
DIN 7337Break mandrel blind rivetsWithdrawnDIN EN ISO 14589, DIN EN ISO 15977, DIN EN ISO 15978, DIN EN ISO 15979, DIN EN ISO 15980, DIN EN ISO 15981, DIN EN ISO 15982, DIN EN ISO 15983, DIN EN ISO 15984, DIN EN ISO 16582, DIN EN ISO 16583, DIN EN ISO 16584ISO 14589, ISO 15977, ISO 15978, ISO 15979, ISO 15980, ISO 15981, ISO 15982, ISO 15983, ISO 15984, ISO 16582, ISO 16583, ISO 16584
DIN 7343Spiral Pins; Normal TypeWithdrawnDIN EN ISO 8750ISO 8750
DIN 7344Spiral Pins; Heavy Duty TypeWithdrawnDIN EN ISO 8748ISO 8748
DIN 7346Spring-Type Straight Pins; (Roll Pins) Light-weight TypeWithdrawnDIN EN ISO 13337ISO 13337
DIN 7349Plain Washers for Bolts with Heavy Clamping SleevesActive
DIN 7500-1Thread rolling screws for metric ISO thread - Part 1: Types, designation, requirementsActive
DIN 7500-2Thread rolling screws for ISO metric thread; guideline values for hole diametersActive
DIN 7504Self-drilling screws with tapping screw thread - Dimensions, requirements and testingWithdrawnISO 10666, ISO 15480, ISO 15481, ISO 15482, ISO 15483
DIN 7513Hexagon head and slotted head thread cutting screws - Dimensions, requirements and testingActive
DIN 7516Cross recessed head thread cutting screws - Dimensions, requirements and testingActive
DIN 7603Ring seals and gasketsActive
DIN 7875Diving accessories for skin divers; terminologyWithdrawn
DIN 7876Diving accessories for skin divers; flippers. dimensions. requirements and testingWithdrawn
DIN 7877Diving accessories for skin divers; diver"s masks. requirements and testingWithdrawn
DIN 7878Diving accessories for skin divers; snorkel; technical requirements of safety, testingWithdrawn
DIN 7962Cross recesses for screws; (modified version of ISO 4757)WithdrawnDIN EN ISO 4757ISO 4757
DIN 7970Threads and thread ends for tapping screws (modified version of ISO 1478)WithdrawnDIN EN ISO 1478ISO 1478
DIN 7971Slotted pan head tapping screwsWithdrawnDIN ISO 1481ISO 1481
DIN 7972Slotted countersunk head tapping screwsWithdrawnDIN ISO 1482ISO 1482
DIN 7973Slotted raised countersunk head tapping screwsWithdrawnDIN ISO 1483ISO 1483
DIN 7977Taper Pins with Thread Ends and Constant Point LengthsWithdrawnDIN EN 28737ISO 8737
DIN 7978Taper Pins with Internal ThreadWithdrawnDIN EN 28737ISO 8736
DIN 7979Parallel Pins with Internal ThreadWithdrawnDIN EN ISO 8733,
DIN EN ISO 8735		ISO 8733,
ISO 8735
DIN 7980Spring lock washers with square ends for cheese head screwsWithdrawn
DIN 7981Cross recessed pan head tapping screwsWithdrawnDIN ISO 7049ISO 7049
DIN 7982Cross recessed countersunk head tapping screwsWithdrawnDIN ISO 7050ISO 7050
DIN 7983Countersunk (Flat) Head Tapping Screws with Cross RecessWithdrawnDIN ISO 7051ISO 7051
DIN 7984Hexagon socket head cap screws with low headActive
DIN 7985Cross recessed raised Phillips Pan head screwsWithdrawnDIN EN ISO 7045ISO 7045
DIN 7989-1Washers for steel structures - Product grade CActive
DIN 7989-2Washers for steel structures - Product grade AActive
DIN 7991Hexagon socket countersunk head cap screwsWithdrawnDIN EN ISO 10642ISO 10642

DIN 8000 to DIN 8999
DIN Title Status DIN replacement Other org
replacement
DIN 8074Polyethylene (PE) pipes – DimensionsActive
DIN 8075Polyethylene (PE) pipes - PE 63, PE 80, PE 100, PE-HD - General quality requirements, testingActive
DIN 8077/8078Polypropylene (PP-R) Pipes -PN 20, PN25 PP-R - General quality requirements, testingActive
DIN 8513-1Brazing and Braze Weld Filler Metals; Copper Base Brazing Alloys; Composition, Use, Technical Conditions of DeliveryWithdrawnDIN EN 1044EN 1044
DIN 8513-2Brazing and Braze Weld Filler Metals; Silver-bearing Brazing Alloys with less than 20% by wt. Silver; Composition, Use, Technical Conditions of DeliveryWithdrawnDIN EN 1044EN 1044
DIN 8513-3Brazing filler metals; silver brazing filler metals containing not less than 20% of silver; composition, application, technical delivery conditionsWithdrawnDIN EN 1044EN 1044
DIN 8513-4Brazing and Braze Weld Filler Metals; Aluminium-Base Brazing Alloys; Composition, Use, Technical Conditions of DeliveryWithdrawnDIN EN 1044EN 1044
DIN 8513-5Brazing filler metals; Nickel base filler metals for high temperature brazing; Application, composition, technical delivery conditionsWithdrawnDIN EN 1044EN 1044
DIN 8580Manufacturing processes - Terms and definitions, divisionActive
DIN 8806-1Narrow band saw blades for woodworking; dimensionsActive
DIN 8515Defects in Metallic Solder Joints; Brazing Joints and High-temperature Solder Joints; Classification, Designations, Explanatory NotesWithdrawnDIN EN ISO 18279:2004-04

DIN 9000 to DIN 9999
DIN Title Status DIN replacement Other org
replacement
DIN 9021Plain washers with large outside diameterWithdrawnDIN EN ISO 7093-1, DIN EN ISO 7093-2ISO 7093-1, ISO 7093-2

DIN 10000 to DIN 19999

DIN 10000 to DIN 10999
DIN Title Status DIN replacement Other org
replacement
DIN 10504Food hygiene - Lamps for the lighting of meat and meat productsWithdrawn

DIN 11000 to DIN 11999
DIN Title Status DIN replacement Other org
replacement
DIN 11024Beta cotter pin (R pin) - Dimensions, materialsActive
DIN 11850Tubes for the food, chemical and pharmaceutical industry - Stainless steel tubes - Dimensions, materialsWithdrawnEN 10357
DIN 11851 Hygienic Unions

DIN 12000 to DIN 12999
DIN Title Status DIN replacement Other org
replacement
DIN 12950-1Laboratory furniture; safety cabinets for microbiological and biotechnological work; safety requirements, testsWithdrawn
DIN 12950-2Laboratory furniture; safety cabinets for microbiological and biotechnological work; containment of class 1 and class 2 cabinets, microbiological testWithdrawn
DIN 12950-10Laboratory furniture; safety cabinets for microbiological and biotechnological work; requirements and testingWithdrawn
DIN 12975-1Thermal solar systems and components - Solar collectors - Part 1: General requirements
DIN 12975-2Thermal solar systems and components - Solar collectors - Part 2: Test methods
DIN 12976-1Thermal solar systems and components - Factory made systems - Part 1: General requirements
DIN 12976-2Thermal solar systems and components - Factory made systems - Part 2: Test methods

DIN 13000 to DIN 13999
DIN Title Status DIN replacement Other org
replacement
DIN 13080Division of hospitals into functional areas and functional sectionsActive
DIN 13260-2Supply systems for medical gases - Part 2: Dimensions and allocation of probes and gas-specific connection points for terminal units for compressed medical gases and vacuumActive
DIN 13432Packaging - Requirements for packaging recoverable through composting and biodegradation - Test scheme and evaluation criteria for the final acceptance of packagingActiveDIN EN 13432
DIN 13715Workpiece corners and edgesActiveDIN ISO 13715(2000–12)

DIN 14000 to DIN 14999
DIN Title Status DIN replacement Other org
replacement
DIN 14090Areas for the fire brigade on premisesActive
DIN 14096-1Fire precaution regulation - Part 1: General and part A (placard); rules for drafting and placardingActive
DIN 14096-2Fire precaution regulation - Part 2: Part B (for persons without special tasks of fire prevention and fire fighting); rules for draftingActive
DIN 14096-3Fire precaution regulation - Part 3: Part C (for persons with special tasks of fire prevention and fire fighting); rules for draftingActive
DIN 14210Water pool for firefightingActive
DIN 14236Ultrasonic domestic gas metersActive
DIN 14406-4Portable fire extinguishers - Part 4: MaintenanceActive
DIN 14503Trailers for firefighting purposes, two-wheeled; general requirementsWithdrawnDIN 14521
DIN 14505Firefighting and rescue service vehicles - Vehicles for roller containers - General requirementsActive
DIN 14507Rescue service vehicles - Vehicles for roller containers - General requirementsActive
DIN 14520Trailers for portable fire pumpsWithdrawn
DIN 14521Firefighting - Trailer with removable foam-water monitorActive
DIN 14530-5Fire fighting vehicles - Part 5: Group pumping appliance LF 10/6, Group pumping appliance for rescue operations HLF 10/6Active
DIN 14530-11Fire fighting vehicles - Part 11: Group pumping appliance LF 20/16, Group pumping appliance for rescue operations HLF 20/16Active
DIN 14530-16Fire fighting vehicles - Part 16: Pumping appliance TSFActive
DIN 14530-17Fire fighting vehicles - Part 17: Pumping appliance TSF-WActive
DIN 14530-21Fire fighting vehicles - Part 21: Pump water tanker TLF 20/40, Pump water tanker TLF 20/40-SLActive
DIN 14530-22Fire fighting vehicles - Part 22: TLF 16/24-TRActive
DIN 14530-24Fire fighting vehicles - Part 24: Small pumping appliance KLFActive
DIN 14530-25Fire fighting vehicles - Part 25: Pumping appliance STLF 10/6Active
DIN 14555-1Vehicles carrying tools and gears - Part 1: General requirementsActive
DIN 14555-3Vehicles carrying tools and gears - Part 3: Emergency tender RWActive
DIN 14555-12Vehicles carrying tools and gears - Part 12: Damage control tender GW-GActive
DIN 14555-21Vehicles carrying tools and gears - Part 21: GW-L1 for logistic tasksActive
DIN 14555-22Vehicles carrying tools and gears - Part 22: GW-L2 for logistic tasksActive
DIN 14565Fire hose tender; Type SW 2000-TRWithdrawn
DIN 14701-1Turntable ladders and similar fire fighting vehicles; Purpose, concepts, safety equipment, requirementsWithdrawnDIN EN 1777EN 1777
DIN 14701-2Turntable ladders and similar fire fighting vehicles; Turn table ladders, engine drivenWithdrawnDIN EN 14043, DIN EN 14044EN 14043, EN 14044
DIN 14701-3Turntable ladders and similar fire fighting vehicles; Rescue basketsWithdrawnDIN EN 1777EN 1777
DIN 14702Turntable ladder DL 16-4, hand operatingActive
DIN 14703Trailer Ladder AL 16-4Active
DIN 14710-1Hook ladder, manufactured using wood; with hinged hookWithdrawnDIN EN 1147EN 1147
DIN 14710-3Hook light metal ladderWithdrawn
DIN 14711-1Scaling ladder; made from woodWithdrawnDIN EN 1147EN 1147
DIN 14711-2Scaling ladder; made from light metalWithdrawnDIN EN 1147EN 1147
DIN 14711-3Scaling ladder; socket rungs and socket partsWithdrawnDIN EN 1147EN 1147
DIN 14713Folding ladderWithdrawnDIN EN 1147EN 1147
DIN 14715-1Three piece extension ladder made from woodWithdrawnDIN EN 1147EN 1147
DIN 14715-2Three piece extension ladder; made of light metalWithdrawnDIN EN 1147EN 1147

DIN 15000 to DIN 15999
DIN Title Status DIN replacement Other org
replacement
DIN 15018-2Cranes; steel structures; principles of design and constructionActive
DIN 15185-1Warehouse systems with guided industrial trucks; requirements on the ground, the warehouse and other requirementsActive
DIN 15185-2Warehousesystems with powered industrials trucks; code of practice for the protection of persons when operating with trucks in narrow aisles; safety requirements, testingActive
DIN 15721Film 70 mm; projection reelActive

DIN 16000 to DIN 16999
DIN Title Status DIN replacement Other org
replacement
DIN 16518Classification of typesActive
DIN 16892Cross-linked high-density polyethylene (PE-X) pipes - General quality requirements and testingActive
DIN 16893Cross-linked high-density polyethylene (PE-X) pipes – DimensionsActive

DIN 17000 to DIN 17999
DIN Title Status DIN replacement Other org
replacement
DIN 17175Seamless Tubes of heat Resistant SteelsWithdrawnDIN EN 10216-2
DIN 17200Steels For Quenching And Tempering - Technical Delivery ConditionsSupersededDIN 10083-1
DIN 10083-2
DIN 10083-3
DIN 17240Heat Resisting and Highly Heat Resisting Materials for Bolts and Nuts; Quality SpecificationsWithdrawnDIN EN 10269
DIN 17410Materials for permanent magnets: Technical conditionsActive
DIN 17457WithdrawnDIN EN 10217-7
DIN 17458WithdrawnDIN EN 10216-5
DIN 17471Resistance alloysActive

DIN 18000 to DIN 18999
DIN Title Status DIN replacement Other org
replacement
DIN 18012House service connections facilities - Principles for planningActive
DIN 18013Recesses for meter boards (electric meters)Active
DIN 18014Foundation earth electrode - General planning criteriaActive
DIN 18015-1Electrical installations in residential buildings - Part 1: Planning principlesActive
DIN 18015-2Electrical installations in residential buildings - Part 2: Nature and extent of minimum equipmentActive
DIN 18015-3Electrical installations in residential buildings - Part 3: Wiring and disposition of electrical equipmentActive
DIN 18022Domestic kitchens, bathrooms and WCs; design principlesWithdrawn
DIN 18024-1Barrier-free built environment - Part 1: Streets, squares, paths, public transport, recreation areas and playgrounds - Design principlesActive
DIN 18024-2Construction of accessible buildings - Part 2: Publicly accessible buildings and workplaces, design principlesActive
DIN 18065Stairs in buildings - Terminology, measuring rules, main dimensionsActive
DIN 18379Construction contract procedures (VOB) - Part C: General technical specifications in construction contracts (ATV) - Installation of air conditioning systemsActive
DIN 18382Contract procedures for building works - Part C: General technical specifications for building works; Low-voltage installation and medium-voltage installation with nominal voltages up to including 36 kVActive
DIN 18384Construction contract procedures (VOB) - Part C: General technical specifications in construction contracts (ATV); Installation of lightning protection systemsActive
DIN 18800-1Steel structures - Part 1: Design and constructionWithdrawnDIN EN 1993
DIN EN 1090
DIN 18800-2Steel structures - Part 2: Analysis of safety against buckling of linear members and framesWithdrawnDIN EN 1993
DIN 18800-3Steel structures - Part 3: Analysis of safety against buckling of platesWithdrawnDIN EN 1993
DIN 18800-4Steel structures - Part 4: Analysis of safety against buckling of shellsWithdrawnDIN EN 1993
DIN 18800-5Steel structures - Part 5: Composite structures of steel and concrete - Design and constructionWithdrawnDIN EN 1994
DIN 18800-7Steel structures - Part 7: Execution and constructor's qualificationActiveEN 1090-2

DIN 19000 to DIN 19999
DIN Title Status DIN replacement Other org
replacement
DIN V 19222Control technology – TerminologyActive
DIN 19225Measurement and control; terminology and classification of controllersActive
DIN 19226-1Control technology - Part 1: General terms and definitionsActive
DIN 19226-2Control technology - Part 2: Terms and definitions; dynamic systems behaviourActive
DIN 19226-3Control technology - Part 3: Terms and definitions of switching systems behaviourActive
DIN 19226-4Control technology - Part 4: Terms and definitions of control systemsActive
DIN 19226-5Control technology - Part 5: Functional termsActive
DIN 19226-6Control technology - Part 6: Terms and definitions of functional and constructional unitsActive
DIN 19227-1Control technology; graphical symbols and identifying letters for process control engineering; symbolic representation for functionsActive
DIN 19227-2Control technology; graphical symbols and identifying letters for process control engineering; representation of detailsActive
DIN 19237Measurement and control; control engineering vocabularyWithdrawnDIN 19226-3, DIN 19226-4,
DIN 19226-5, DIN 19226-6
DIN 19227-1Control technology; graphical symbols and identifying letters for process control engineering; symbolic representation for functionsWithdrawnDIN EN 62424
DIN 19227-2Control technology; graphical symbols and identifying letters for process control engineering; representation of detailsActive
DIN 19533Pipe-lines of high-density PE (high-density polyethylene) and low-density PE (low-density polyethylene) for drinking water supply; pipes, pipe connections and fittings for pipe-linesWithdrawnDIN EN 12201-1,
DIN EN 12201-2,
DIN EN 12201-3,
DIN EN 12201-5		EN 12201-1,
EN 12201-2,
EN 12201-3,
EN 12201-5
DIN 19704-1Hydraulic steel structures - Part 1: Criteria for design and calculationActive
DIN 19704-2Hydraulic steel structures - Part 2: Design and manufacturingActive
DIN 19704-3Hydraulic steel structures - Part 3: Electrical equipmentActive

DIN 20000 to DIN 29999
DIN Title Status DIN replacement Other org
replacement
DIN 20066Fluid technology - hose lines, dimensions, specifications
DIN 20163Explosives work
DIN 21800Hammer and chisel signs (mining symbol)
DIN 21908Mining crevice work; colours
DIN 22101Conveyor belt for bulk material, fundamentals, analysis and design
DIN 22107Arrangements for belt conveyor rollers
DIN 22112Rollers: dimensions, specifications, testing
DIN 23307Seat leathers for the mining industry (miner's apron)
DIN 23342Clothing for the mining industry – men's vest with 1/4 sleeves
DIN 23345Clothing for the mining industry – men's underpants 1/1 length (Long Johns)

DIN 24000 to DIN 24999

systems - Concepts - Part 1: Classification Lubrication || Active || ||

DIN Title Status DIN replacement Other org
replacement
DIN 24190Ventilation and air conditioning - folded and welded rectangular sheet metal ductsWithdrawn
DIN 24340-2Hydraulic valves; mounting surfaces and connecting plates for directional control valvesActive

DIN 28000 to DIN 28999
DIN Title Status DIN replacement Other org
replacement
DIN 28610-1Ductile iron pressure pipes with socket with cement-mortar lining for gas and water pipelines; dimensions and massesWithdrawnDIN EN 545, DIN EN 969EN 545, EN 969
DIN 28610-2Ductile iron pressure pipes with socket for gas and water pipelines rated for pressures over 4 bar up to and including 16 bar; dimensions and massesWithdrawnDIN EN 969EN 969

DIN 30000 to DIN 39999
DIN Title Status DIN replacement Other org
replacement
DIN 30722-1Roller contact tipper vehicles, roller containers - Part 1: Roller contact tipper vehicles up to 26 t, roller containers type 1570 made from steelActive
DIN 30722-2Roller contact tipper vehicles, roller containers - Part 2: Roller contact tipper vehicles up to 32 t, roller containers type 1570 made from steelActive
DIN 30722-3Roller contact tipper vehicles, roller containers - Part 3: Roller contact tipper vehicles up to 12 t, roller containers type 900 made from steelActive
DIN 30722-4Roller containers for the transport on road and railActive

DIN 31000 to DIN 31999
DIN Title Status DIN replacement Other org
replacement
DIN 31635Conversion of the Arabic alphabetActive
DIN 32676 Tri-Clamp Fittings[2] Active

DIN 40000 to DIN 49999
DIN Title Status DIN replacement Other org
replacement
DIN 40015Frequency and wave bandsActive
DIN 40020Guidelines for the user interface in multimedia equipment for general purpose use (IEC/TR 61997:2001)Active
DIN 40050-9Road vehicles; degrees of protection (IP-code); protection against foreign objects; water and contact; electrical equipmentActive
DIN 40101-1Graphical symbols for use on equipmentWithdrawn
DIN 40101-2Graphical symbols for use on equipment; graphical symbols from ISO 7000 for electrical engineeringActive
DIN 40108Electric power technology - Current systems - Concepts, quantities, letter symbolsActive
DIN 40110-1Quantities used in alternating current theory - Part 2: Two-line circuitsActive
DIN 40110-2Quantities used in alternating current theory - Part 2: Multi-line circuitsActive
DIN 40146-1Telecommunications - Part 1: Basic conceptsActive
DIN 40148-1Transmission systems and two-ports; concepts and quantitiesActive
DIN 40148-2Transmission systems and two-ports; symmetry characteristics of linear two-portsActive
DIN 40148-3Transmission systems and two-ports; measures for attenuationActive
DIN 40200Nominal value, limiting value, rated value, rating - conceptsActive
DIN 41215Electrical communication engineering; electromagnetic relays, definitionsWithdrawn
DIN 41301Electro Sheets; Magnetic Materials for TransformersWithdrawn
DIN 41309-1Small transformers and chokes; strip-wound cut cores; types SM, SE, SU, SG and S3U; dimensions materialsWithdrawn
DIN 41309-2Small transformers and chokes; strip-wound cut cores; technical conditions of delivery for one phase applications; types SM, SE, SU and SGWithdrawn
DIN 41309-3Small transformers and chokes; strip-wound cut cores; technical conditions of delivery for three phase applications; type S3UWithdrawn
DIN 41426Nominal values of resistors and capacitorsWithdrawnDIN IEC 60063IEC 60063
DIN 41429Colour code for fixed resistorsWithdrawnDIN EN 60062EN 60062
DIN 41524Circular connectors for radio and associated sound equipment three and five-pole connectorsWithdrawn
DIN 41612-1Two-part connectors for printed board, grid 2,54 mm; common mounting features; survey of typesWithdrawnDIN 41612-1 S1
DIN 41612-1 S1Two piece connectors for printed circuits, grid 2,54 mm (0,1 in); general allusionsWithdrawnDIN EN 60603-2EN 60603-2
DIN 41612-2Two-part connectors for printed boards; grid 2,54mm; dimensions of types B, C and DWithdrawnDIN EN 60603-2EN 60603-2
DIN 41612-3Two part connectors for printed boards; grid 2,54mm; dimensions of types F and GWithdrawnDIN EN 60603-2EN 60603-2
DIN 41612-4Two-part connectors for printed boards; grid 2,54mm, dimensions of type HWithdrawnDIN EN 60603-2EN 60603-2
DIN 41612-5Two-part connectors for printed boards; grid 2,54mm; ratings, requirements, testsWithdrawnDIN EN 60603-2EN 60603-2
DIN 41612-6Two-part connection for printed boards; grid 2.54mm; dimensions of types Q, R and SWithdrawnDIN EN 60603-2EN 60603-2
DIN 41612-7Two-part connectors for printed boards; grid 2,54 mm; dimensions of types U and VWithdrawnDIN EN 60603-2EN 60603-2
DIN 41612-8Two-part connectors for printed boards; grid 2.54 mm; dimensions of type MWithdrawnDIN EN 60603-2EN 60603-2
DIN 41612-8 S1Two-part connectors for printed boards; grid 2.54 mm; dimensions of type M; survey of special contracts for use with type MWithdrawnDIN EN 60603-2EN 60603-2
DIN 41612-9Two-part connectors for printed boards; grid 2,54 mm; dimensions of type EWithdrawnDIN EN 60603-2EN 60603-2
DIN 41612-10Two-part connectors for printed boards; grid 2,54mm; gaugesWithdrawnDIN EN 60603-2EN 60603-2
DIN 41612-102Two-part connectors for printed boards; dimensions for type XWithdrawnDIN 41612-9
DIN 41612-103Two-part connectors for printed boards; dimensions of type MWithdrawnDIN 41612-8
DIN 41652-1Rack and panel connectors, trapezoidal, round contacts 1 mm; common mounting features and dimensions; survey of typesActive
DIN 41652-2Rack and panel connectors; trapezoidal, round contacts 1 mm; ratings, requirements, testsActive
DIN 41750-1Rack and panel connectors, trapezoidal, round contacts ø1 mm; common mounting features and dimensions; survey of typesActive
DIN 41750-2Rack and panel connectors, trapezoidal, round contacts ø1 mm; ratings, requirements, testsActive
DIN 41750-3Rack and panel connectors, trapezoidal, round contacts ø1 mm; dimensions of type A; solder termination for free wiringActive
DIN 41750-5Rack and panel connectors, trapezoidal, round contacts ø1 mm; dimensions of type C; crimp termination for free wiringActive
DIN 41782Guidelines for the presentation of published dataWithdrawnDIN IEC 60747-2IEC 60747-2
DIN 41786Thyristors, definitionsWithdrawn
DIN 41855Semiconductor devices and integrated circuits; kinds of devices and general termsWithdrawn
DIN 41855-2Semiconductor devices and integrated circuits; optoelectronic semiconductor devices; terms and definitionsWithdrawn
DIN 41868Cases 10 A 3 and 10 B 3 for semiconductor devices; main dimensionsWithdrawn
DIN 41869-1Case 23 A 3 for semiconductor devices; main dimensionsWithdrawn
DIN 41869-2Cases 34 A 2 and 34 A 3 for semiconductor devices; main dimensionsWithdrawn
DIN 41869-3Case 11 A 3 and 11 B 3 for semiconductor devices; main dimensionsWithdrawn
DIN 41869-4Case 12 A 3 for semiconductor devices; main dimensionsWithdrawn
DIN 41869-5Case 13 A 3 for semiconductor devices; main dimensionsWithdrawn
DIN 41869-6Case 14 A 3 for semiconductor devices; main dimensionsWithdrawn
DIN 41869-7Case type 15 for semiconductor devices; main dimensionsWithdrawn
DIN 41873Cases type 5 for semiconductor devices and integrated circuitsWithdrawn
DIN 41876Cases 18 A, B and C with 2 up to 4 terminals for semiconductor devices; main dimensionsWithdrawn
DIN 42400Terminal markings for electrical equipment; general rules, alphanumeric systemWithdrawnDIN EN 60445EN 60445
DIN 42402Terminal markings for power transformers and reactorsActive
DIN 42403Terminal markings for power convertersWithdrawnDIN IEC 61148IEC 61148
DIN 42673-1Totally enclosed fan-cooled three-phase induction motors squirrel-cage, type IM B 3, with rolling bearing; mounting dimensions and relationship frame sizes-output ratingsWithdrawn
DIN 42673-2Totally enclosed fan-cooled three-phase induction motors with squirrel-cage, type IM B 3, with rolling bearings; relationship frame sizes - output ratings for type of protection increased safety "e"Active
DIN 42673-3Totally enclosed fan-cooled three-phase induction motors with squirrel-cage, type IM B 3, with rolling bearings; relationship frame sizes - output ratings for type of protection flameproof enclosure "d"Active
DIN 42673-4Totally enclosed fan-cooled alternating-current polyphase motors with squirrel-cage, design B3, with ball bearings, maximum envelope dimensionsActive
DIN 42961Rating plates for rotating electrical machinery; designActive
DIN 42973Rated output values for rotating electrical machinery for continuous dutyActive
DIN 43700Measurement and control - Measurement and control instruments for panel mounting - Nominal front- and cut-out-dimensionsWithdrawnDIN IEC 61554IEC 61554
DIN 43780Electrical measuring instruments; direct acting indicating electrical measuring instruments and their accessoriesWithdrawnDIN EN 60051-1EN 60051-1
DIN 43802-2Line scales and pointers for indicating electrical measuring instruments; general requirementsActive
DIN 43802-3Line scales and pointers for indicating electrical measuring instruments; designs and dimensionsActive
DIN 43802-4Line scales and pointers for indicating electrical measuring instruments; scale graduation and numberingActive
DIN 43807Measuring and control; electrical measuring instruments; terminal markings for switchboard meters, panel meters and measuring transducers for the measurement of power and power factorActive
DIN 43856Electricity meters, tariff time switches and ripple control receivers; connection diagrams, terminal marking, circuit diagramsActive
DIN 43856-2Electricity meters - Part 2: Marking of auxiliary terminals for tariff devices according to IEC-Report 61354:1995Active
DIN 43870-1Meter mounting boards; dimensions based on a grid systemActive
DIN 43870-2Meter mounting boards; functional areaActive
DIN 43870-3Meter panels; wiringsActive
DIN 44070-1Meter mounting boards; dimensions based on a grid systemActive
DIN 44070-2Meter mounting boards; functional areaActive
DIN 44070-3Meter panels; wiringsActive
DIN 44070-4Meter panels; cover for wiringActive
DIN 44080Thermistors; PTC, technical terms and testsWithdrawn
DIN 44300Information processing; vocabularyWithdrawn
DIN 44300-1Information processing - Concepts - General termsWithdrawn
DIN 44300-2Information processing - Concepts - Representation of dataWithdrawn
DIN 44300-3Information processing - Concepts - Data structuresWithdrawn
DIN 44300-4Information processing - Concepts – ProgrammingWithdrawn
DIN 44300-5Information processing - Concepts - Components of digital computer systemsWithdrawn
DIN 44300-6Information processing - Concepts – StorageWithdrawn
DIN 44300-7Information processing - Concepts – TimesWithdrawn
DIN 44300-8Information processing - Concepts - Processing functionsWithdrawn
DIN 44300-9Information processing - Concepts - Process relations and modes of operationWithdrawn
DIN 45322Circular connectors for radio and associated sound equipment; six-pole connectorsWithdrawnDIN EN 60130-9EN 60130-9
DIN 45323Connectors for coupling an external low-voltage power to portable entertainment equipment (describes at least two DC coaxial power plugs)Active
DIN 45500-1High fidelity audio equipment and systems; minimum performance requirements; Part 1: generalWithdrawnDIN EN 61305-1EN 61305-1
DIN 45500-2High fidelity audio equipment and systems; requirements for tuner equipmentsWithdrawnDIN EN 61305-2EN 61305-2
DIN 45500-3High fidelity audio equipment and systems; requirements for disk record reproducing equipmentsWithdrawn
DIN 45500-4High fidelity audio equipment and systems; minimum performance requirements for magnetic recording and reproducing equipmentWithdrawn
DIN 45500-5High fidelity audio equipment and systems; minimum performance requirements for microphonesWithdrawn
DIN 45500-6High fidelity audio equipment and systems; minimum performance requirements for amplifiersWithdrawnDIN EN 61305-3EN 61305-3
DIN 45500-7High fidelity audio equipment and systems; requirements for loudspeakersWithdrawnDIN EN 61305-5EN 61305-5
DIN 45500-8High fidelity audio equipment and systems; for sets and systemsWithdrawn
DIN 45500-9High fidelity audio equipment and systems; minimum requirements for magnetic tapes 4 and 6 for audio recordingsWithdrawn
DIN 45500-10High fidelity audio equipment and systems; minimum performance requirements for headphonesWithdrawn
DIN 45507Measuring apparatus for frequency variations in sound recording equipmentWithdrawnDIN IEC 60386IEC 60386
DIN 45539Disk record reproducing equipment; directives for measurements, markings and audio frequency connections, dimensions of interchangeable pickups, requirements of play back amplifiersWithdrawnDIN IEC 60098IEC 60098
DIN 45596Microphones; phantom poweringWithdrawn
DIN 46400-1Steel flats with special magnetic properties cold rolled, non - oriented, finally annealed magnetic sheet and strip hysteresis loss at frequencies above 100 HzWithdrawnDIN EN 10106EN 10106
DIN 46400-3Grain-oriented magnetic steel and strip technical conditionsWithdrawnDIN EN 10107EN 10107
DIN 47100Cords for telecommunication; code of insulated conductors, colour of sheathWithdrawn
DIN 47301-1Terms of HF-linesActive
DIN 47301-2Terms of HF-linesActive
DIN 47301-3Definition of radio frequency transmission lines - mean characteristic impedance - mean standing wave ratioActive
DIN 48803Lightning protection system; Arrangement of components and dimensions for mountingWithdrawn
DIN 48830Lightning protection system; DescriptionWithdrawn

DIN 51097 to DIN 59999
DIN Title Status DIN replacement Other org
replacement
DIN 51097Testing of floor coverings; determination of the anti-slip properties: wet-loaded barefoot areas; walking method; ramp testWithdrawnDIN 51130
DIN 51130Testing of floor coverings; determination of the anti-slip properties: workrooms and fields of activities with slip danger, walking method - ramp testWithdrawnDIN 51097
DIN 51501Lubricants; Lubricating Oils L-AN; Minimum RequirementsWithdrawn
DIN 52368Testing of particleboards; determination of formaldehyde emission by gas analysisWithdrawnDIN EN 717-2EN 717-2
DIN 53150Paints and varnishes - Determination of the drying stage of coatings (modified Bandow-Wolff method)Active
DIN 53438Testing of combustible materials; response to ignition by small flameActive
DIN 53452Testing of Plastics; Flexural TestWithdrawnDIN EN ISO 178ISO 178
DIN 53575Flexible Cellular Polymeric Materials - Determination of Tear StrengthWithdrawnDIN EN ISO 8067ISO 8067
DIN 54836Testing of combustible materials; determination of ignition temperatureActive
DIN 54837Determination of burning behaviour using a gas burnerActive
DIN 55003-3Machine tools; symbols; numerically controlled machine toolsWithdrawn
DIN 58145Measuring Method for determination of solarization effect of fused silica optical fibersActive
DIN 58810Surgical implants; threads for bone screws and nutsWithdrawn
DIN 58888Thread connection for microscope objectivesWithdrawnDIN ISO 8038-1ISO 8038-1

DIN ISO 53438

DIN 60000 to DIN 69999
DIN Title Status DIN replacement Other org
replacement
DIN 66000Information processing; switching algebra, mathematical signs and symbolsActive
DIN 66001Information processing; graphical symbols and their applicationActive
DIN 66002Information processing; handwriting of the digit 0 and of the upper case letter OActive
DIN 66003Information technology - 7-bit codeActive
DIN 66004-1Information processing - Coding on data media - Part 1: Representation of 7-bit code character sets on punched tape 25Active
DIN 66004-2Information processing - Coding on data media - Part 2: Representation of 7-bit coded and 8-bit coded character sets on punched cardsActive
DIN 66004-3Information processing - Coding on data media - Part 3: Representation of 7-bit coded and 8-bit coded character sets on magnetic tape 12Active
DIN 66004-4Information processing - Coding on data media - Part 4: Representation of 7-bit coded and 8-bit coded character sets on magnetic tape cassette 3,8Active
DIN 66004-5Information processing - Coding on data media - Part 5: Representation of 7-bit coded and 8-bit coded set on media-flexible disk cartridgeActive
DIN 66005Information processing; representation of packed numerics and binary data recorded on 9 tracks on magnetic tape 12Active
DIN 66006Presentation of ALGOL/ALCOR programs on paper tape and punch cardsWithdrawn
DIN 66007Font CMC 7 for magnetic ink character recognition; characters and nominal dimensionsWithdrawnDIN ISO 1004ISO 1004
DIN 66008-1Font A for optical character recognition; characters and nominal dimensionsActive
DIN 66008-6Font A for optical character recognition; characters and nominal dimensions; extension of the character setActive
DIN 66008-7Font A for optical character recognition; representation of characters by dots in a 9 × 9 matrixActive
DIN 66009Font B for optical character recognition; characterWithdrawn
DIN 66020-1Functional requirements for the interface between data terminal equipment and data circuit-terminating equipment - Part 1: General applicationActive
DIN 66020-2List of definitions for interchange circuits between data terminal equipment (DTE) and data circuit-terminating equipment (DCE) in public data networksActive
DIN 66020-4Data transmission; interface between data circuit-terminating equipment (DCE) and data terminal equipment (DTE)Active
DIN 66020-9Interface between data terminal equipment (DTE) and data circuit-terminating equipment (DCE) for synchronous transmission on group band circuits at 48,000 bits per secondActive
DIN 66021-1Data transmission; interface between data circuit-terminating equipment (DCE) and data terminal equipment (DTE)Active
DIN 66021-2Interface between data terminal equipment (DTE) and data circuit-terminating equipment (DCE) for synchronous transmission on group band circuits at 48,000 bits per secondActive
DIN 66025-1Numerical control of machines, format; general requirementsActive
DIN 66025-2Industrial automation; numerical control of machines; format, preparatory and miscellaneous functionsActive
DIN 66027Information processing; programming language FORTRANWithdrawn
DIN 66215-1Programming of numerically controlled machines; CLDATA, general structure and record typesActive
DIN 66215-2Programming of numerically controlled machines; CLDATA; minor elements of type 2000 records (post-processor commands)Active
DIN 66253-2Information processing; programming language PEARL1998
DIN 66234Information processing; programming language PL/IActive
DIN 66255Information processing; programming language PL/IActive
DIN 66256Information processing; programming language PascalWithdrawn
DIN 66257Numerical control of machines; conceptsWithdrawnDIN ISO 2806ISO 2806
DIN 66258-1Interfaces and basic data link control procedures for data communication; C S-interface, V S-interfaceWithdrawn
DIN 66258-2Interface and basic data link control procedures for data communication; balanced interface for start-stop transmission using basic data link control procedures on point-to-point connectionWithdrawn
DIN 66261Information processing; Nassi-Shneiderman flowchart symbolsActive
DIN 66264-1Industrial automation systems and integration - Multiprocessor Control System for Industrial Machines (MPST) - Part 1: Parallel busActive
DIN 66264-2Multiprocessor control system for industrial machines (MPST); industrial automatics; rules for information interchangeActive
DIN 66303Information technology - 8 bit codeActive
DIN V 66304Industrial automation; Computer Aided Design; format for the exchange of standard parts dataActive
DIN 66325-2Local and Metropolitan Area Networks; LLC; identical with ISO 8802-2:1989WithdrawnISO 8802-2
DIN 66325-4Local and Metropolitan Area Networks; token-passing bus access method; identical with ISO/IEC 8802-4:1990WithdrawnISO/IEC 8802-4
DIN 66399Three-part standard regarding the seven security levels of paper shredders; replaces DIN 32757Active
DIN 69901Project controlling; project management; conceptsActive

DIN 70000 to DIN 79999
DIN Title Status DIN replacement Other org
replacement
DIN 71412Lubricating nipples; cone typeActive
DIN 72311-1Lead storage batteries; starter batteries for motorcycles, nominal capacities, main dimensionsActive
DIN 72311-4Lead storage batteries; starter batteries, terminals, vent plugs and filler openingsActive
DIN 72311-8Lead storage batteries; starter batteries for motor cycles and passenger carsActive
DIN 72311-13Lead storage batteries; starter batteries for starting, lighting and ignition, 12 V, 27, 36, 45 and 54 Ah, for lateral basic fastening 10,5Active
DIN 72311-16Lead storage batteries; starter batteries for starting, lighting and ignition, 12 V, 27, 36, 45, 54 and 63 Ah, for lateral basic fastening 19Active
DIN 72311-17Lead storage batteries; starter batteries, protective covering for terminalActive
DIN 72311-18Lead storage batteries; starter batteries with basic fastening 10,5 for passenger cars and commercial vehicles; nominal capacities, main dimensionsActive
DIN 72311-20Lead storage batteries; starter batteries for commercial vehicles; nominal capacities and main dimensionsActive
DIN 72311-21Lead storage batteries; starter batteries with 10,5 basic fastening lugs for commercial vehicles; nominal capacities and main dimensionsActive
DIN 72552-1Terminal markings for motor vehicles; scope, principles, requirementsActive
DIN 72552-2Terminal markings for motor vehicles; codesActive
DIN 72552-3Terminal markings for motor vehicles; examples for application on circuit diagramsActive
DIN 72552-4Terminal markings for motor vehicles; summaryActive
DIN 75490Radio communication devices in motor vehicles; installation space, general requirementsActive

See also

References
  1. DK 621.882.245 Deutsche Normen Dec. 1952 Linsensenkschrauben mit Längsschlitz
  2. "What is DIN 32676? | Sanitary Fittings". sanitaryfittings.us. Retrieved 18 September 2018.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.