Vauxhall Cresta

The Vauxhall Cresta is a British car which was produced by Vauxhall from 1954 to 1972. The Cresta was introduced in 1954 as an upmarket version of the Vauxhall Velox, itself a six-cylinder version of the Vauxhall Wyvern. The Cresta models were the E (1954–1957), PA (1957–1962), PB (1962–1965) and PC (1965–1972). The Viscount (1966–1972) was an upmarket Cresta PC.

Vauxhall Cresta
Vauxhall Cresta PB
Overview
ManufacturerVauxhall (General Motors)
Production1954-1972
AssemblyUnited Kingdom
Australia,[1]
New Zealand (1966-on)
Body and chassis
RelatedVauxhall Velox
Vauxhall Wyvern
Chronology
SuccessorVauxhall Victor FE

Cresta E

Vauxhall Cresta E
Overview
Production1954-1957
166,504 produced.[2]
Body and chassis
Body style4-door saloon
Powertrain
Engine2.3 L ohv I6
Transmission3-speed manual
Dimensions
Wheelbase103 in (2,600 mm)[3]
Length172 in (4,400 mm)[4]
Width66.5 in (1,690 mm)[4]
Height61.5 in (1,560 mm)[4]

The Vauxhall Velox had been introduced in 1948, with a new version in 1951. The Cresta E version, launched in 1954, had the same 2262 cc six cylinder engine in the same state of tune but scored over the Velox in having a choice of leather or fabric upholstery, optional two tone paintwork, a heater as standard, a small electric fascia mounted clock, a cigar lighter, a lamp automatically illuminating the boot when opened and a vanity mirror on the inside of the front passenger's sun visor along with a special ornamental badge above the V (for Vauxhall) badge on the nose of the car. A radio was optional.

In October 1955 a facelift model with deeper front and rear screens was introduced. The balanced drop windows were replaced by ones with proper winding mechanisms, there were interior trim improvements, separate amber rear flasher lights and windscreen washers became standard. A new chrome plated grille with fewer vertical slats replaced the earlier diecast version. This model was assembled in New Zealand, alongside the Wyvern and Velox, with 840 being built in 1956, according to a local owners' group with access to copies of the GM Petone plant ledgers. More changes were made in October 1956, with a new grille with horizontal bars, higher compression ratio engine, electrically operated windscreen wipers (replacing the camshaft driven system) and changes to the body trim and two tone colour scheme. In June 1957 the Cresta received a redesigned engine of the same capacity based on the deeper block design introduced in four-cylinder form in the Victor F series in March of that year.

A Cresta tested by the British magazine The Motor in 1956 had a top speed of 82.2 mph (132.3 km/h) and could accelerate from 0-60 mph (97 km/h) in 20.2 seconds. A petrol consumption of 23.5 miles per imperial gallon (12.0 L/100 km; 19.6 mpgUS) was recorded. The test car cost £931 including taxes.[4]

Cresta PA

Vauxhall Cresta PA
PA SY 1961
Overview
Production1957-1962
81,841 made[2][5]
Body and chassis
Body style4-door saloon
5-door estate car
Powertrain
Engine2,262 cc ohv I6 (1958-1960)
2,651 cc ohv I6 (1961-1962)
Transmission3-speed manual, Overdrive optional
Hydramatic Automatic available from 1961
Dimensions
Wheelbase105 in (2,700 mm)[3]
Length179 in (4,500 mm) Saloon
Width68.5 in (1,740 mm)[6]
Height57 in (1,400 mm)[6]

The PA Cresta, announced 2 October 1957,[7] is probably the best-known version. It mimicked the American fashion for tail-fins, wrap-around windows and white-wall tyres, taking its cues from the 1957 model Buick Special announced twelve months before the Cresta, though understated compared to the Cadillacs and Buicks of the time. All factory-built PAs were four-door saloons: the estate cars were converted by Friary of Basingstoke, Hampshire and are rare today.

The PA Cresta had independent front suspension using coil springs and an anti-roll bar with a rigid axle and semi-elliptic leaf springs at the rear. The Lockheed brakes used 9 in (230 mm) drums all round. Carried over from the last of the E series cars, the 2,262 cc six-cylinder engine had pushrod-operated overhead valves and a compression ratio of 7.8:1 (a low compression 6.8:1 version was available); it produced 82.5 bhp (61.5 kW) at 4,400 rpm.[6] A single Zenith carburettor was used. The transmission had three forward speeds.

It was well equipped with leather and nylon upholstery for its bench front and rear seats and woven pile carpet. A heater was fitted as standard. The radio remained an option on the home market. Other options included fog lamps, reversing light, locking filler cap and external mirrors. In order to keep the front floor clear to seat six people the handbrake lever was mounted under the dashboard and the gearchange lever was column mounted. The car could be ordered painted in either single or two tone colours.

A PA tested by the British magazine The Motor in 1958 had a top speed of 89.8 mph (144.5 km/h) and could accelerate from 0-60 mph (97 km/h) in 16.8 seconds. A petrol consumption of 25.2 miles per imperial gallon (11.2 L/100 km; 21.0 mpgUS) was recorded. The test car cost £1073 including taxes of £358.[6] They tested the 2.6 Litre version with overdrive in 1960 and found the top speed had increased to 94.7 mph (152.4 km/h), acceleration from 0-60 mph (97 km/h) to 15.2 seconds and fuel consumption improved to 26.8 miles per imperial gallon (10.5 L/100 km; 22.3 mpgUS). The test car cost £1077 including taxes of £317. The car without overdrive cost £1014.[8]

Australian assembly of the PA Cresta began in May 1958 by General Motors Holden. Subsequent models were assembled up until 1965.[9]

In August 1959 the Cresta was given a facelift, with a new, larger, grille and the replacement of the three piece rear window with a single wrap around screen. The previous ribbed roof panel was replaced with a smoothly contoured version (with structural revisions to the C pillars and rear parcel shelf area to retain structural strength). The Vauxhall flutes on the front wings finally disappeared, replaced by a straight chrome side moulding which was also the division point for the two tone colour scheme. Further changes came in August 1960 with the introduction of a new engine of square dimensions (bore and stroke were both 82.55mm) with a redesigned, longer, cylinder block and a capacity of 2651cc. A further increase in compression ratio to 8.0:1 and larger valves in wedge shaped combustion chambers contributed to a power output of 95bhp at 4,600rpm. Increased diameter wheels allowed larger brakes to be fitted, but these were still of the drum type (Ford had introduced front disc brakes as an option on the rival Zephyr/Zodiac models in September 1960 and would make them standard in June 1961).

Externally, there was a redesign of the rear lights, with shallower units replacing the elongated oval ones of the previous versions. The direction indicators, previously in the rear tail fins were now incorporated in the main lamp unit and the fins were now solid with a V for Vauxhall badge. The rear bumper was now a higher mounted straight topped design. The front sidelights and direction indicators, previously separate were now in a combined housing and there were redesigned wheel trims and hub caps. Inside, a redesigned fascia with a padded top and a horizontal speedometer was featured. In October 1961 the final updates to the PA series were made. Front disc brakes became an optional extra (four months after Ford had made them standard on the Zephyr/Zodiac). Separate front seats became an option to the standard bench and there was now wood trim to the fascia and door cappings. The PA Cresta continued in production in this form until replaced by the PB series in October 1962.

During the 1970s many PA Crestas were modified and customised. The model was very popular with fifties revivalists; many were driven by teddy boys and were very much seen as part of the rock 'n' roll image. A 1960 PA Cresta features in the 1981 video for "Ghost Town" by The Specials, in which the band are wearing '50s-style clothing.The Specials Ghost Town Car can now be seen in The Coventry Music Museum.

Today the PA Cresta is a recognised classic, with the other variants perhaps less appreciated but gaining recognition. One famous PA owner in the late 1950s was Don Lang.

Cresta PB

Vauxhall Cresta PB
Vauxhall Cresta PB Saloon (post face-lift)
Overview
Production1962–1965
87,047 made[2]
AssemblyUnited Kingdom
Australia[10]
Body and chassis
Body stylefour-door saloon
five-door estate car
Powertrain
Engine2,651 cc ohv I6
3,294 cc OHV I6
Transmission3 or 4-speed manual
2 or 3-speed automatic
Dimensions
Wheelbase107.5 in (2,730 mm)
Length181.75 in (4,616 mm)
Width70.25 in (1,784 mm)
Height56.5 in (1,440 mm) [3]

The PB was a major styling revision, completely eliminating the tailfins, with a flat bonnet and generally more conservative styling taking its cues from the Victor FB introduced the previous year and with which it shared its doors. The engine was the same 2,651 cc (162 cu in) straight six as the last of the PA series and although the compression ratio was increased to 8.5:1, power output remained at 95 bhp. Front disc brakes were now fitted as standard. In October 1963 an estate conversion was made available, the work carried out by Martin Walter Ltd. of Bedford Dormobile fame and fully approved by Vauxhall. The conversion featured a steel-framed glass fibre roof extension and tailgate. The rear doors with squared-off window frames were straight from the factory-built Victor estate. In October 1964 the engine was increased in capacity to 3293 cc by virtue of a larger, 92 mm, bore in combination with the original 82.55 mm stroke. Power increased to 115 bhp at 4,200 rpm. The model received a new full-width chrome grille incorporating the headlights and there was a full-length chrome strip along the body sides.

The gearbox was still three-speed with column change but an overdrive was available. As standard, the 3.3-litre cars had a three-speed column-change gearbox, with a four-speed floor-change unit as an option. Three-speed hydramatic automatic transmission was available with both engines but this was changed to the two-speed Powerglide unit towards the end of the 3.3-litre PB run. Servo-assisted brakes, with discs at the front, were fitted. Minor changes to gearing and the option of power steering were introduced early in 1965 and the PB series continued until replaced by the PC models in October of that year.

Australia continued to locally assemble the PB Cresta. New Zealand fully imported the PB Cresta from Britain.

Cresta PC

Vauxhall Cresta PC
Overview
Production1965-1972
53,912 made[2]
Body and chassis
Body style4-door saloon
5-door estate car
Powertrain
Engine3,294 cc ohv I6
Transmission3 or 4-speed manual
2 or 3-speed automatic
Dimensions
Wheelbase107.5 in (2,730 mm)[3]
Length185.5 in (4,710 mm) (saloon)
187 in (4,700 mm) (estate)[11]
Width69.8 in (1,770 mm)
Height55.6 in (1,410 mm) (saloon)
59 in (1,500 mm) (estate)[11]
Curb weight2,796 lb (1,268 kg) (standard)

The last of the series, the PC, was introduced for the London Motor Show in October 1965.[12] No longer offered as a lower specification Velox version, it was designated PCS (standard), PCD (Deluxe) and PCE (Executive), this last having its own name, 'Viscount'. It was a different car, larger and styled with the coke-bottle look that would also be seen in the FD Victor series: it now resembled a slightly smaller Chevrolet Impala. It was similar to the Australian Holden HR, but larger and better trimmed, and featured the 123 DIN/142 SAE hp 3.3-litre straight-six engine for its entire seven-year production run. Though a small-block V8 would have dropped straight in, this option was never offered in Europe. Initially, the three-speed column-shift manual transmission was standard with optional overdrive; four-speed manual and two-speed Powerglide were also optional. Later cars, from about 1971, came with four-speed manual or three-speed automatic, both having floor shift and bucket seats. The De-Luxe version had four headlamps instead of the two fitted on the (much rarer) base models.

General Motors Holden assembly of the Cresta ended in 1965, therefore the PC Cresta was not sold in Australia.

General Motors New Zealand ran its own assembly line in Petone (1966-67) and Trentham, near Wellington, to 1971. Up until 1966 the Cresta was fully imported from Britain. From 1966 the Petone plant began locally assembly of the Cresta. The one 'base' Cresta model built changed very little during that time and did not receive the facelift that appeared on the UK market late in 1970 as the 1971 model. The only option was the 2 speed Powerglide. However, at some point in production (1970) the brake system was upgraded to a tandem master cylinder to improve the braking, and this upgrade became a standard fitment on the New Zealand models. A few twin-headlamp Cresta Deluxe, Viscount and estate car versions were also imported, built-up, from the UK.

The facelifted model, never offered in New Zealand, had twin headlamps as standard and a more integrated dash panel. Floor shift, rather than column change, was also standard.

Vauxhall Cresta PC from behind)

In January 1967 domestic market deliveries began of the Vauxhall Cresta estate car.[11] This vehicle resulted from a conversion by Martin Walter of Folkestone, a firm better known for their (primarily Bedford based) Dormobile motorhome conversions.[11] The estate version was 2 12 inches (6.4 cm) higher than the saloon due to a combination of heavy-duty rear suspension, an increase in the outer diameter of the tyres (to 7.00-14 in from 5.90-14in) and the modified roof line.[11] The Cresta estate was initially offered in the UK at £1,507, which represented a price premium of around 40% over the equivalent saloon.[11] The long established Humber Hawk estate and recently introduced Ford Zephyr estate carried UK sales prices of £1,342 and £1,379 respectively. The Cresta estate offered a load platform length of 47 inches (120 cm) which increased to an impressive 76 inches (190 cm) when the back seat was folded down,[11] but Vauxhall's contender was never priced to be a big seller and the last estate cars were made in 1968.

Viscount

Vauxhall Viscount
Overview
Production1966-1972
7,025 made[2]
Body and chassis
Body style4-door saloon
Powertrain
Engine3.3 L straight-6 ohv
5.2 L (318 cu) Chrysler V8 (South Africa)
Transmission4-speed manual
2 or 3-speed automatic
Dimensions
Wheelbase107.5 in (2,730 mm)
Length188.6 in (4,790 mm)
Width69.8 in (1,770 mm)
Height56.0 in (1,420 mm)
Curb weight3,071 lb (1,393 kg)

Introduced early in June 1966,[12] with the same engine and mechanical components as the Cresta PC, the Viscount was the super de-luxe version of it. It was supplied as standard with power steering, electric windows, reclining seats, a vinyl roof, walnut dashboard, inertia reel seat belts front, and even a heated rear window. Areas of the grille and headlamp surrounds were blacked out to give a classier look and the tail-lights had a chrome overlay. The dark green, blue or maroon paintwork featured simulated, hand painted coachlines, along each flank, to give the car a coachpainted appearance. The outer pair of the quad, five inch, sealed beam headlamps were twin filament, giving the car four main beams.[12] The Viscount also came with wider tyres and rims than the Cresta (7.00-14in on 5" rims rather than 5.90-14in on 4.5" rims).[12] All PC 3.3 had twin tail-pipes. The standard transmission option was GM's Powerglide 2-speed automatic system, but a four speed manual gearbox was available, initially on the UK market at a saving of £85:[12] elsewhere the manual gear box was a no-cost option. In the third quarter of 1970 the two-speed Powerglide automatic was replaced with a GM 3-speed automatic transmission.[12]

Some South African versions were fitted with a Chrysler V8 as an option - one of the rare times a General Motors product used a direct rival's engine.

The British version of the Vauxhall Viscount automatic with the 2-speed Powerglide transmission was road tested by Motor ref.33/66 on 3 September 1966. A maximum (best) top speed of 100mph was recorded with 0-60 mph in 14.5secs, Standing quarter mile in 20.3secs. Overall mpg was 15.6. The later automatic Viscount model, with the 3 speed Strasbourg GM transmission, ought to have improved on these acceleration figures, especially at the lower speeds.[13]

Use by British Royalty

In the 1950s and 60s Queen Elizabeth II used a bespoke PA Friary Estate, and later a PC version of the Cresta as personal transport. The Queen's PA Friary estate forms part of The Royal Car Collection at the Sandringham Exhibition & Transport Museum.[14][15]

References

  1. "1959 Chevrolet & Pontiac in Australia". Retrieved 3 September 2011.
  2. Sedgwick, M.; Gillies.M (1986). A-Z of Cars 1945-1970. Devon, UK: Bay View Books. ISBN 978-1-870979-39-9.
  3. Culshaw; Horrobin (1974). Complete Catalogue of British Cars. London: Macmillan. ISBN 978-0-333-16689-5.
  4. "The Vauxhall Cresta". The Motor. 6 June 1956.
  5. Oldtimer Katalog. Nr. 23. Königswinter: HEEL Verlag GmbH. 2009. pp. Seite 42. ISBN 978-3-86852-067-5.
  6. "The Vauxhall Cresta Model PA". The Motor. 23 April 1958.
  7. "Two New Vauxhall Models". The Times (53961). 2 October 1957. p. 5.
  8. "The Vauxhall Cresta". The Motor. 21 September 1960.
  9. https://www.shannons.com.au/club/news/1958-62-vauxhall-pa-veloxcresta-did-australians-still-need-holden/
  10. "The Chevy II Race on Sales and Track". m.shannons.com.au. Archived from the original on 31 December 2012. Retrieved 22 November 2012.
  11. "Martin Walter Cresta Estate Car". Autocar. Vol. 126 no. 3699. 5 January 1967. p. 13.
  12. "Used Car Test: Vauxhall Viscount". Autocar. Vol. 134 no. 3920. 13 May 1971. pp. 25–26.
  13. Motor magazine dated 03/09/1966 road test ref. 33/66.
  14. Tominey, Camilla (14 July 2013). "How Queen almost got Mercury's car". Express.co.uk. Retrieved 27 December 2013.
  15. "Our British history & your stories – Vauxhall Motors UK". Vauxhall and I. 30 May 2013. Retrieved 27 December 2013.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.