Audio signal processing

Audio signal processing is used when broadcasting audio signals in order to enhance their fidelity or optimize for bandwidth or latency. In this domain, the most important audio processing takes place just before the transmitter. The audio processor here must prevent or minimize overmodulation, compensate for non-linear transmitters (a potential issue with medium wave and shortwave broadcasting), and adjust overall loudness to desired level.

Active noise control is a technique designed to reduce unwanted sound. By creating a signal that is identical to the unwanted noise but with the opposite polarity, the two signals cancel out due to destructive interference.

Audio synthesis is the electronic generation of audio signals. A musical instrument that accomplishes this is called a synthesizer. Synthesizers can either imitate sounds or generate new ones. Audio synthesis is also used to generate human speech using speech synthesis.

Audio effects are systems designed to alter how an audio signal sounds. Unprocessed audio is metaphorically referred to as dry, while processed audio is referred to as wet.[12]

• delay or echo - To simulate the effect of reverberation in a large hall or cavern, one or several delayed signals are added to the original signal. To be perceived as echo, the delay has to be of order 35 milliseconds or above. Short of actually playing a sound in the desired environment, the effect of echo can be implemented using either digital or analog methods. Analog echo effects are implemented using tape delays or bucket-brigade devices. When large numbers of delayed signals are mixed a reverberation effect is produced; The resulting sound has the effect of being presented in a large room.
• flanger - to create an unusual sound, a delayed signal is added to the original signal with a continuously variable delay (usually smaller than 10 ms). This effect is now done electronically using DSP, but originally the effect was created by playing the same recording on two synchronized tape players, and then mixing the signals together. As long as the machines were synchronized, the mix would sound more-or-less normal, but if the operator placed his finger on the flange of one of the players (hence "flanger"), that machine would slow down and its signal would fall out-of-phase with its partner, producing a phasing comb filter effect. Once the operator took his finger off, the player would speed up until it was back in phase with the master, and as this happened, the phasing effect would appear to slide up the frequency spectrum. This phasing up-and-down the register can be performed rhythmically.
• phaser - another way of creating an unusual sound; the signal is split, a portion is filtered with a variable all-pass filter to produce a phase-shift, and then the unfiltered and filtered signals are mixed to produce a comb filter. The phaser effect was originally a simpler implementation of the flanger effect since delays were difficult to implement with analog equipment.
• chorus - a delayed version of the signal is added to the original signal. The delay has to be short in order not to be perceived as echo, but above 5 ms to be audible. If the delay is too short, it will destructively interfere with the un-delayed signal and create a flanging effect. Often, the delayed signals will be slightly pitch shifted to more realistically convey the effect of multiple voices.
• equalization - frequency response is adjusted using audio filter(s) to produce desired spectral characteristics. Frequency ranges can be emphasized or attenuated using low-pass, high-pass, band-pass or band-stop filters. Moderate use of equalization can be used to fine-tune the tonal quality of a recording; extreme use of equalization, such as heavily cutting a certain frequency can create more unusual effects. Band-pass filtering of voice can simulate the effect of a telephone because telephones use band-pass filters.
• overdrive effects can be used to produce distorted sounds, and increase loudness. The most basic overdrive effect involves clipping the signal when its absolute value exceeds a certain threshold.
• timescale-pitch modification - this effect shifts a signal up or down in pitch. For example, a signal may be shifted an octave up or down. Blending the original signal with shifted duplicate(s) can create harmonization. Another application of pitch shifting is pitch correction where a musical signal is adjusted to improve intonation. The complement of pitch shift is timescale modification, that is, the process of changing the speed of an audio signal without affecting its pitch.
• resonators - emphasize harmonic frequency content on specified frequencies. These may be created from parametric equation or from delay-based comb-filters.
• robotic voice effects are used to make an actor's voice sound like a synthesized human voice.
• ring modulation is an effect made famous by Doctor Who's Daleks and commonly used throughout sci-fi.
• dynamic range compression - the control of the dynamic range of a sound to avoid unintentional or undesirable fluctuation in level. Dynamic range compression is not to be confused with audio data compression, where the amount of data is reduced without affecting the amplitude of the sound it represents.
• 3D audio effects - placement of sounds outside the spatial range available through stereo or surround imaging.
• wave field synthesis - a spatial audio rendering technique for the creation of virtual acoustic environments.
• De-esser - control of sibilance in speech and singing.