Fluid coupling

An important characteristic of a fluid coupling is its stall speed. The stall speed is defined as the highest speed at which the pump can turn when the output turbine is locked and full input torque (at the stall speed) is applied. Under stall conditions all of the engine's power at that speed would be dissipated in the fluid coupling as heat, possibly leading to damage.

A modification to the simple fluid coupling is the step-circuit coupling which was formerly manufactured as the "STC coupling" by the Fluidrive Engineering Company.

The STC coupling contains a reservoir to which some, but not all, of the oil gravitates when the output shaft is stalled. This reduces the "drag" on the input shaft, resulting in reduced fuel consumption when idling and a reduction in the vehicle's tendency to "creep".

When the output shaft begins to rotate, the oil is thrown out of the reservoir by centrifugal force, and returns to the main body of the coupling, so that normal power transmission is restored.[6]

A fluid coupling cannot develop output torque when the input and output angular velocities are identical.[7] Hence a fluid coupling cannot achieve 100 percent power transmission efficiency. Due to slippage that will occur in any fluid coupling under load, some power will always be lost in fluid friction and turbulence, and dissipated as heat. Like other fluid dynamical devices, its efficiency tends to increase gradually with increasing scale, as measured by the Reynolds number.

As a fluid coupling operates kinetically, low-viscosity fluids are preferred.[7] Generally speaking, multi-grade motor oils or automatic transmission fluids are used. Increasing density of the fluid increases the amount of torque that can be transmitted at a given input speed.[8] However, hydraulic fluids, much like other fluids, are subject to changes in viscosity with temperature change. This leads to a change in transmission performance and so where unwanted performance/efficiency change has to be kept to a minimum, a motor oil or automatic transmission fluid, with a high viscosity index should be used.

Fluid couplings can also act as hydrodynamic brakes, dissipating rotational energy as heat through frictional forces (both viscous and fluid/container). When a fluid coupling is used for braking it is also known as a retarder.[5]

Correct operation of a fluid coupling depends on it being correctly filled with fluid. An under-filled coupling will be unable to transmit the full torque, and the limited fluid volume is also likely to overheat, often with damage to the seals.

If a coupling is deliberately designed to operate safely when under-filled, usually by providing an ample fluid reservoir which is not engaged with the impeller, then controlling its fill level may be used to control the torque which it can transmit, and in some cases to also control the speed of a load.[lower-alpha 2]

Controlling the fill level is done with a 'scoop', a non-rotating pipe which enters the rotating coupling through a central, fixed hub. By moving this scoop, either rotating it or extending it, it scoops up fluid from the coupling and returns it to a holding tank outside the coupling. The oil may be pumped back into the coupling when needed, or some designs use a gravity feed - the scoop's action is enough to lift fluid into this holding tank, powered by the coupling's rotation.

Scoop control can be used for easily managed and stepless control of the transmission of very large torques. The Fell diesel locomotive, a British experimental diesel railway locomotive of the 1950s, used four engines and four couplings, each with independent scoop control, to engage each engine in turn. It is commonly used to provide variable speed drives.[9][10]

Fluid couplings are used in many industrial application involving rotational power,[11][12] especially in machine drives that involve high-inertia starts or constant cyclic loading.

Fluid couplings are found in some Diesel locomotives as part of the power transmission system. Self-Changing Gears made semi-automatic transmissions for British Rail, and Voith manufacture turbo-transmissions for diesel multiple units which contain various combinations of fluid couplings and torque converters.

Fluid couplings were used in a variety of early semi-automatic transmissions and automatic transmissions. Since the late 1940s, the hydrodynamic torque converter has replaced the fluid coupling in automotive applications.

In automotive applications, the pump typically is connected to the flywheel of the engine—in fact, the coupling's enclosure may be part of the flywheel proper, and thus is turned by the engine's crankshaft. The turbine is connected to the input shaft of the transmission. While the transmission is in gear, as engine speed increases, torque is transferred from the engine to the input shaft by the motion of the fluid, propelling the vehicle. In this regard, the behaviour of the fluid coupling strongly resembles that of a mechanical clutch driving a manual transmission.

Fluid flywheels, as distinct from torque converters, are best known for their use in Daimler cars in conjunction with a Wilson pre-selector gearbox. Daimler used these throughout their range of luxury cars, until switching to automatic gearboxes with the 1958 Majestic. Daimler and Alvis were both also known for their military vehicles and armoured cars, some of which also used the combination of pre-selector gearbox and fluid flywheel.

The most prominent use of fluid couplings in aeronautical applications was in the DB 601, DB 603 and DB 605 engines where it was used as a barometrically controlled hydraulic clutch for the centrifugal compressor and the Wright turbo-compound reciprocating engine, in which three power recovery turbines extracted approximately 20 percent of the energy or about 500 horsepower (370 kW) from the engine's exhaust gases and then, using three fluid couplings and gearing, converted low-torque high-speed turbine rotation to low-speed, high-torque output to drive the propeller.