Chevrolet Corvette

The first generation of Corvette was introduced late in the 1953 model year. It first appeared as a show car for the 1953 General Motors Motorama, held January 17–23 at New York's Waldorf-Astoria Hotel.[8] At the time, Chevrolet general manager Thomas H. Keating said it was six months to a year away from production readiness.[9] The car generated enough interest to induce GM to make a production version to sell to the public. First production was on June 30, 1953.[10][11][12]

1953 Chevrolet Corvette displayed at the 1953 GM Motorama car show

This generation was often referred to as the "solid-axle" models (the independent rear suspension was not introduced until the second generation).[13] Three hundred hand-built Corvette convertibles were produced, all Polo White, for the 1953 model year.[14]

The 1954 model year vehicles could be ordered in Pennant Blue, Sportsman Red, Black, or Polo White; 3,640 were built, and sold slowly.

The 1953, 1954, and 1955 model years were the only Corvettes equipped with a 235 cu in (3.9 L) version of the second- generation Blue Flame inline-six rated at 150 hp (112 kW; 152 PS).

The 1955 model offered a 265 cu in (4.34 L) V8 engine as an option. Despite the poor sales of the Corvette at the time, the brand new V-8 was an overwhelmingly popular option. Only 6 of the 1955 models were produced with the inline-six. With a large inventory of unsold 1954 models, GM limited production to 700 for 1955. With the new V8, the 0–60 mph time improved by 1.5 seconds.,[12] and saw two new competitors called the Ford Thunderbird and the Studebaker Speedster introduced that same year.

1956 Chevrolet Corvette transistorized "hybrid" (vacuum tubes and transistors) car radio option, which was GM's first start in using the modern solid-state electronics for a production car model.

A new body was introduced for the 1956 model featuring a new "face" and side coves; the taillamp fins were also gone.[15] An optional "Ramjet" fuel injection system was made available in the middle of the 1957 model year. It was one of the first American mass-produced engines in history to reach 1 bhp (0.75 kW) per cubic inch (16.4 cubic cm) and Chevrolet's advertising agency used a "one hp per cubic inch" slogan for advertising the 283 bhp (211 kW) 283 cu in (4.64 L) Small-Block engine.[16] Other options included power windows (1956), hydraulically operated power convertible top (1956), heavy duty brakes and suspension (1957), and four speed manual transmission (late 1957).[16] Delco Radio transistorized signal-seeking "hybrid" car radio, which used both vacuum tubes and transistors in its radio's circuitry (1956 option).[17][18]

The 1958 Corvette received a body and interior freshening which included a longer front end with quad headlamps, bumper exiting exhaust tips, a new steering wheel, and a dashboard with all gauges mounted directly in front of the driver.[19] Exclusive to the 1958 model were hood louvers and twin trunk spears.[19] The 1959–60 model years had few changes except a decreased amount of body chrome and more powerful engine offerings.[20]

In 1961, the rear of the car was completely redesigned with the addition of a "duck tail" with four round lights. The light treatment would continue for all following model year Corvettes until 2014.[21] In 1962, the Chevrolet 283 cu in (4.64 L) Small-Block was enlarged to 327 cu in (5.36 L). In standard form it produced 250 bhp (190 kW). For an extra 12% over list price, the fuel-injected version produced 360 bhp (270 kW),[22] making it the fastest of the C1 generation. 1962 was also the last year for the wrap around windshield, solid rear axle, and convertible-only body style.[23] The trunk lid and exposed headlamps did not reappear for many decades.[24]

• 
  1953 Corvette exits assembly line
• 
  1954 Corvette convertible
• 
  1956 Corvette convertible
• 
  1959 Corvette convertible (rear)
• 
  1960 Corvette convertible

1963 Corvette Sting Ray coupe

The second generation (C2) Corvette, which introduced Sting Ray to the model, continued with fiberglass body panels, and overall, was smaller than the first generation. The C2 was later referred to as mid-years.[25] The car was designed by Larry Shinoda with major inspiration from a previous concept design called the "Q Corvette," which was created by Peter Brock and Chuck Pohlmann under the styling direction of Bill Mitchell.[26] Earlier, Mitchell had sponsored a car known as the "Mitchell Sting Ray" in 1959 because Chevrolet no longer participated in factory racing. This vehicle had the largest effect on the styling of this generation, although it had no top and did not give away what the final version of the C2 would look like.[27] The third inspiration was a mako shark Mitchell had caught while deep-sea fishing.[28]

Production started for the 1963 model year and ended in 1967. Introducing a new name, "Sting Ray", the 1963 model was the first year for a Corvette coupé and it featured a distinctive tapering rear deck (a feature that later reappeared on the 1971 "Boattail" Buick Riviera) with, for 1963 only, a split rear window. The Sting Ray featured hidden headlamps, non-functional hood vents, and an independent rear suspension.[29] Corvette chief engineer Zora Arkus-Duntov never liked the split rear window because it blocked rear vision, but Mitchell thought it to be a key part of the entire design. Maximum power for 1963 was 360 bhp (270 kW) and was raised to 375 bhp (280 kW) in 1964. Options included electronic ignition, the breakerless magnetic pulse-triggered Delcotronic first offered on some 1963 Pontiac models.[30] On 1964 models the decorative hood vents were eliminated and Duntov, the Corvette's chief engineer, got his way with the split rear window changed to a full-width window.

1965 Corvette Sting Ray coupe

Four-wheel disc brakes were introduced in 1965, as was a "big block" engine option: the 396 cu in (6.49 L) V8. Side exhaust pipes were also optionally available in 1965, and continued to be offered through 1967. The introduction of the 425 bhp (317 kW) 396 cu in (6.49 L) big block in 1965 spelled the beginning of the end for the Rochester fuel injection system.[31] The 396 cu in (6.49 L) option cost US$292.70 while the fuel injected 327 cu in (5.36 L) engine cost US$538.00. Few people could justify spending US$245.00 more for 50 bhp (37 kW) less, even though FI could deliver over 20 mpg on the highway and would keep delivering fuel despite high G-loading in corners taken at racing speeds. Another rare '63 and '64 option was the Z06 competition package, which offered stiffer suspension, bigger, multi-segment lined brakes with finned drums, and more. Only a couple hundred coupes and a single convertible were factory-equipped this way in 1963. With only 771 fuel-injected cars built in 1965, Chevrolet discontinued the option at the end of the '65 production, having introduced a less-expensive big block 396 engine rated at 425 hp in the middle of the production year and selling over 2,000 in just a few months. For 1966, Chevrolet introduced an even larger 427 cu in (7.00 L) Big Block version. Other options available on the C2 included the Wonderbar auto-tuning AM radio, AM-FM radio (mid-1963), air conditioning (late-1963), a telescopic steering wheel (1965), and headrests (1966). The Sting Ray's independent rear suspension was successfully adapted for the new-for-1965 Chevrolet Corvair, which solved the quirky handling problems of that unique rear-engine compact.[32]

1967 Corvette Sting Ray convertible

1967 was the final model year for the second generation. The 1967 model featured restyled fender vents, less ornamentation, and back-up lamps which were on the inboard in 1966 were now rectangular and centrally located. The first use of all four taillights in red started in 1961 and was continued thru the C2 line-up except for the 1966. The 1967 and subsequent models continuing on all Corvettes since. 1967 had the first L88 engine option which was rated at 430 bhp (320 kW), but unofficial estimates place the actual output at 560 bhp (420 kW) or more.[33] Only twenty such engines were installed at the factory. From 1967 to 1969, the Holley triple two-barrel carburetor, or Tri-Power, was available on the 427 L89 (a $368 option, on top of the cost for the high-performance 427).[34] Despite these changes, sales slipped more than 15%, to 22,940 (8,504 coupes, off close to 15%, and 14,436 convertibles, down nearly 19%).[note 1]

Duntov came up with a lightweight version of the C2 in 1962. Concerned about Ford and what they were doing with the Shelby Cobra, GM planned to manufacture 100 Grand Sport Corvettes, but only five were actually built.[35] They were driven by historic drivers such as Roger Penske, A. J. Foyt, Jim Hall, and Dick Guldstrand among others. Today the five cars (001-005) are all held by private owners, and are among the most coveted and valuable Corvettes ever built.[36] 002 is exhibited in the Simeone Foundation Automotive Museum and is in running condition.[37]

1969 Corvette Stingray coupe with T-top panels removed

Corvette Sting Ray tail lights

The third generation Corvette, patterned after the Mako Shark II concept car, was introduced for the 1968 model year and was in production until 1982. C3 coupes featured the first use of T-top removable roof panels. It introduced monikers that were later revived, such as LT-1, ZR-1, Z07, and Collector Edition. In 1978, the Corvette's 25th anniversary was celebrated with a two-tone Silver Anniversary Edition and an Indy Pace Car replica edition of the C3. This was also the first time that a Corvette was used as a Pace Car for the Indianapolis 500.[38]

Engines and chassis components were mostly carried over from the C2, but the body and interior were new. The 350 cu in (5.7 L) engine replaced the old 327 cu in (5.36 L) as the base engine in 1969, but power remained at 300 bhp (224 kW). 1969 was the only year for a C3 to optionally offer either a factory installed side exhaust or normal rear exit with chrome tips. The all-aluminum ZL1 engine was also new for 1969; the special big-block engine was listed at 430-hp (320 kW), but was reported to produce 560 hp (420 kW) and propelled a ZL1 through the 1/4 mile in 10.89 seconds.[39]

There was an extended production run for the 1969 model year due to a lengthy labor strike, which meant sales were down on the 1970 models, to 17,316.[40] 1970 small-block power peaked with the optional high compression, high-revving LT-1 that produced 370 bhp (276 kW). The 427 big-block was enlarged to 454 cu in (7.44 L) with a 390 bhp (291 kW) rating. The ZR-1 special package was an option available on the 1970 through 1972 model years, and included the LT-1 engine combined with special racing equipment. Only 53 ZR-1's were built.[41]

In 1971, to accommodate regular low-lead fuel with lower anti-knock properties, the engine compression ratios were lowered which resulted in reduced power ratings. The power rating for the 350 cu in (5.7 L) L48 base engine decreased from 300 to 270 horsepower and the optional special high performance LT1 engine decreased from 370 to 330 horsepower. The LS5 454 cu in (7.4 L) motor was carried over and produced 365 hp (272 kW). Offered in ‘71 only was the LS6 454 cu in (7.4 L) big-block featuring aluminum heads and delivering 425 hp (317 kW), highest of the 1970-72 series, and could be ordered with an automatic transmission. For the 1972 model year, GM moved to the SAE Net measurement which resulted in further reduced, but more realistic, power ratings than the previous SAE Gross standard.[42] Although the 1972 model's 350 cu in (5.7 L) horsepower was actually the same as that for the 1971 model year, the lower net horsepower numbers were used instead of gross horsepower. The L48 base engine was now rated at 200 bhp (150 kW) and the optional LT1 engine was now rated at 270 bhp (200 kW).[24] 1974 models had the last true dual exhaust system that was dropped on the 1975 models with the introduction of catalytic converters requiring the use of no-lead fuel. Engine power decreased with the base ZQ3 engine producing 165 bhp (123 kW), the optional L82's output 205 bhp (153 kW), while the 454 big-block engine was discontinued. Gradual power increases after 1975 peaked in 1980 with the model's optional L82 producing 230 bhp (172 kW) in its final year.[20] 1981 saw a single engine, the L81, which had 190 bhp (142 kW) while the fuel-injected 1982 L83 had 200 bhp (149 kW).[43] [44]

Styling changed subtly throughout the generation until 1978 for the car's 25th anniversary. The Sting Ray nameplate was not used on the 1968 model, but Chevrolet still referred to the Corvette as a Sting Ray; however, the 1969 (through 1976) models used the "Stingray" name as one word, without the space.[45] In 1970, the body design was updated including fender flares, and interiors were refined, which included redesigned seats, and indication lights near the gear shift that were an early use of fiber optics . Due to government regulation, the 1973 Corvette's chrome front bumper was changed to a 5-mile-per-hour (8 km/h)system with a urethane bumper cover.[46] 1973 Corvettes are unique in that sense, as they are the only year where the front bumper was polyurethane and the rear retained the chrome two-piece bumper set. 1973 was also the last year chrome bumpers were used. The optional wire-spoked wheel covers (left) were offered for the last time in 1973. Only 45 Z07 were built in 1973. From 1974 onwards both the front and rear bumpers were polyurethane.[11]

In 1974, a 5-mile-per-hour (8 km/h) rear bumper system with a two-piece, tapering urethane bumper cover replaced the Kamm-tail and chrome bumper blades, and matched the new front design from the previous year. 1975 was the last year for the convertible, (which did not return for 11 years) and Dave McLellan succeeded Zora Arkus-Duntov as the Corvette's Chief Engineer.[47] For the 1976 models the fiberglass floor was replaced with steel panels to provide protection from the catalytic converter's high operating temperature. For 15 model years the names Corvette, Sting Ray, and Stingray were synonymous. 1977 was last year the tunneled roof treatment with a vertical back window was used, in addition, leather seats were available at no additional cost for the first time. The black exterior color returned after a six-year absence.[48]

The 1978 25th Anniversary model introduced the fastback glass rear window and featured a new interior and dashboard. Corvette's 25th anniversary was celebrated with the Indy 500 Pace Car limited edition and a Silver Anniversary model featuring silver over gray lower body paint. All 1979 models featured the previous year's pace car seats and offered the front and rear spoilers as optional equipment.[25] 53,807 were produced for the model year, making 1979 the peak production year for all versions of the Corvette. Sales have trended downward since then.[49] In 1980, the Corvette received an integrated aerodynamic redesign that resulted in a significant reduction in drag. After several years of weight increases, 1980 Corvettes were lighter as engineers trimmed both body and chassis weight.[19] In mid-1981, production relocated from St. Louis, to Bowling Green, Kentucky (where all subsequent Corvette generations have since been manufactured), and several two-tone paint options were offered. The 1981 models were the last available with a manual transmission until well into the 1984 production run. In 1982, a fuel-injected engine returned, and a final C3 tribute Collectors Edition featured an exclusive, opening rear window hatch.[19]

• 
  1971 Corvette Stingray coupe
• 
  Corvette Sting Ray detail
• 
  1974 Corvette Stingray coupe
• 
  1978 Corvette Indy 500 Pace Car Edition (rear)

1984 Corvette with targa top open

The fourth-generation Corvette was the first complete redesign of the Corvette since 1963. Production was to begin for the 1983 model year but quality issues and part delays resulted in only 43 prototypes for the 1983 model year being produced that were never sold. All of the 1983 prototypes were destroyed or serialized to 1984 except one with a white exterior, medium blue interior, L83 350 ci, 205 bhp V8, and 4-speed automatic transmission.[10] After extensive testing and modifications were completed, it was initially retired as a display sitting in an external wall over the Bowling Green Assembly Plant's employee entrance. Later this only surviving 1983 prototype was removed, restored, and is now on public display at the National Corvette Museum in Bowling Green, Kentucky. It is still owned by GM.[50][51] On February 12, 2014, it was nearly lost to a sinkhole which opened up under the museum. Eight other Corvettes were severely damaged.[52]

Regular fourth generation production began on January 3, 1983; the 1984 model year and delivery to customers began in March 1983. The 1984 model carried over the 350 cu in (5.7 L) L83 slightly more powerful (5 bhp) "Crossfire" V8 engine from the final 1982 third-generation model.[25] New chassis features were aluminum brake calipers and an all-aluminum suspension for weight savings and rigidity. The new one-piece Targa top had no center reinforcement. A new electronic dashboard with digital liquid crystal displays for the speedometer and tachometer was standard. Beginning in 1985, the 230 bhp (170 kW) L98 engine with tuned port fuel injection became the standard engine.[10]

September 1984 through 1988 Corvettes offered a Doug Nash designed "4+3" transmission – a 4-speed manual coupled to an automatic overdrive on the top three gears. It was designed to help the Corvette meet U.S. fuel economy standards.[53] Since 1981 (when it was last offered), a manual transmission returned to the Corvette starting with production in late 1984. The transmission proved to be problematic and was replaced by a modern ZF 6-speed manual transmission in 1989.[54]

In 1986, the second Corvette Indy Pace Car was released. It was the first convertible Corvette since 1975. A Center High Mounted Signal Light (CHMSL) – a third center brake light – was added in 1986 to comply with safety regulations. While the color of the pace car used in the race was yellow, all 1986 convertibles also had an Indy 500 emblem mounted on the console, making any color a "pace car edition". In 1987, the B2K twin-turbo option became available from the factory. The Callaway Corvette was a Regular Production Option (RPO B2K). The B2K option coexisted from 1990 to 1991 with the ZR-1 option, which then replaced it. Early B2Ks produced 345 bhp (257 kW) and 450 lb⋅ft (610 N⋅m);[55] later versions boasted 450 bhp (336 kW) and 613 lb⋅ft (831 N⋅m).[56]

1988 saw the 35th Anniversary Edition of the Corvette. Each of these featured a special badge with an identification number mounted next to the gear selector, and were finished with a white exterior, wheels, and interior.[19] In 1990, the ZR1 option Corvette was introduced with the LT5 engine designed by Lotus and built in the Mercury Marine plant in Stillwater, Oklahoma. The LT5 engine was a 4 cam (DOHC) design producing 375 hp (280 kW) when at "open throttle". The C4 ZR1 ran from 1990 thru 1995 model years. In 1991, all Corvettes received updates to the body, interior, and wheels. The convex rear fascia that set the 1990 ZR-1 apart from the base model was now included on L98 Corvettes, making the styling of the expensive ZR-1 even closer to that of the base cars. The most obvious difference remaining between the base and ZR-1 models besides the wider rear wheels was the location of the CHMSL, which was integrated into the new rear fascia used on the base model, but remained at the top of the rear-hatch on the ZR-1's.[24]

For the 1992 model year, the 300 bhp (220 kW) LT1 engine was introduced, an increase of 50 bhp (37 kW) over 1991's L98 engine. This engine featured reverse-flow cooling (the heads were cooled before the block), which allowed for a higher compression ratio of 10.5:1. A new distributor was also debuted. Called "Optispark", the distributor was driven directly off the front of the camshaft and mounted in front of the timing cover, just above the crankshaft and harmonic balancer.[24] Also new for 1992 was Acceleration Slip Regulation (ASR), a form of traction control that utilized the Corvette's brakes, spark retard, and throttle close-down to prevent excessive rear wheel spin and possible loss of control. The traction control device could be switched off if desired.[19]

A special 40th Anniversary Edition was released in 1993, which featured a commemorative Ruby Red color, 40th anniversary badges, and embroidered seat backs. The 1993 Corvette also marked the introduction of the Passive Keyless Entry System, making it the first GM car to feature it. Production of the ZR-1 ended in 1995, after 6,939 cars had been built.[53] 1996 was the final year of C4 production, and featured special models and options, including the Grand Sport and Collector Edition, OBD II (On-Board Diagnostics), run flat tires, and the LT4 engine. The 330 bhp (246 kW) LT4 V8 was available only with a manual transmission, while all 300 bhp (224 kW) LT1 Corvettes used automatic transmissions.[31]

Chevrolet released the Grand Sport (GS) version in 1996 to mark the end of production of the C4 Corvette. The Grand Sport moniker was a nod to the original Grand Sport model produced in 1963. A total of 1,000 GS Corvettes were produced, 810 as coupes and 190 as convertibles.[31] The 1996 GS came with the high-performance LT4 V8, producing 330 bhp (246 kW) and 340 lb⋅ft (460 N⋅m). The Grand Sport came only in Admiral Blue with a white stripe down the middle, black wheels, and two red stripes on the front left wheel arch.[57]

• 
  1986 Corvette convertible Indy 500 Pace Car Edition
• 
  1988 Corvette coupe
• 
  1992 Corvette ZR-1
• 
  1996 Corvette Grand Sport

Corvette C5 coupe

The C5 Corvette was redesigned from the ground up after sales from the previous generation began to decline. Production of the C5 Corvette actually began in 1996 but quality/manufacturing issues saw its release to the public in mass delayed until 1997, and continuing through the 2004 model year. The C5 was a completely new design that featured many new concepts and manufacturing breakthroughs that would be carried forward to the C6 & C7. It had a top speed of 176 mph (283 km/h) and was judged by the automotive press as a breakthrough with vastly improved dynamics in nearly every area over the previous C4 design. Innovations included a 0.29 drag coefficient, near 50/50 weight distribution, active handling (the first stability control for a Corvette). It also weighed less than the C4.

Corvette C5 convertible

An all new LS1 aluminum engine (Gen III small block) featured individual ignition coils for each cylinder, and aluminum block and pistons. It was initially rated at 345 bhp (257 kW) and 350 lb⋅ft (470 N⋅m), but was increased to 350 bhp (260 kW) in the 2001 edition. The new engine, combined with the new body, was able to achieve up to 28 mpg on the highway.[58][59][60][61][62][63][64][65][66][67]

Corvette Z06

For its first year, the C5 was available only as a coupe, although the new platform was designed from the ground up to be a convertible, which returned in 1998, followed by the fixed-roof coupe (FRC) in 1999. One concept for the FRC was for it to be a stripped-down model with a possible V6 engine (nicknamed in-house as the "Billy Bob").[68] By 2000, FRC plans laid the groundwork for the return in 2001 of the Z06, an RPO option not seen since Zora's 1963 race-ready Corvette.[69]

The Z06 model replaced the FRC model as the highest performance C5 Corvette. Instead of a heavier double-overhead cam engine like the ZR-1 of the C4 generation, the Z06 used an LS6, a 385 bhp (287 kW) derivative of the standard LS1 engine. Using the much more rigid fixed roof design allowed the Z06 unprecedented handling thanks to upgraded brakes and less body flex.[70] Those characteristics, along with the use of materials such as a titanium exhaust system and a carbon fiber hood in the 2004 model year, led to further weight savings and performance gains for the C5 Z06. The LS6 was later upgraded to 405 bhp (302 kW)for 2002–2004. Although the Z06's rated power output equal to that of the C4 ZR-1, the improved rigidity, suspension, brakes, and reduced weight of the C5 produced a car quicker than C4 ZR-1.[71]

Corvette C6 coupe

Corvette ZR1

2010 Corvette Grand Sport

For the C6 Corvette GM wanted to focus more upon refining the C5 than trying to redesign it.[72] Car & Driver, and Motor Trend, described the C6 as an "evolution of the C5, instead of a complete redo". The C6 wheelbase was increased while body overhangs were decreased when compared to the C5. Retractable headlights were replaced with fixed units. The C6 brought a new and improved interior compared to the C5. As a result of the upgraded interior, the C6 had a slight increase in passenger hip room. It also sported an updated LS1/LS6 engine now called the LS2. This engine was primarily an LS1/LS6 with a bump in displacement from 5.7L to 6.0 liters. The increased displacement of the 6.0 bumped the LS2's horsepower up by 50 BHP over its LS1 progenitor, although still 5 BHP less than the upgraded LS6 engine found in the previous C5 Z06. Thus the LS2 was now at 364 cu in, and it produced 400 bhp (300 kW) at 6000 rpm and 400 lb⋅ft (540 N⋅m) at 4400 rpm, giving the vehicle a 0–60 mph time of under 4.2 seconds.[73] Its top speed was 190 mph (310 km/h).

The C6 generation did not match the previous generation's relatively good fuel economy, despite its relatively low 0.28 drag coefficient and low curb weight, achieving 16/26 mpg (city/highway) equipped with automatic or manual transmissions; like all manual transmission Corvettes since 1989, it is fitted with Computer Aided Gear Selection (CAGS) to improve fuel economy by requiring drivers to shift from 1st gear directly to 4th in low-speed/low-throttle conditions. This feature helps the C6 avoid the Gas Guzzler Tax by achieving better fuel economy.[74]

The new Z06 arrived as a 2006 model in the third quarter of 2005. It has a 7.0 L version of the small block engine codenamed LS7. At 427.6 cubic inches, the Z06 was the largest small block ever offered from General Motors. Because of the Corvette's former use of 427 cubic-inch big blocks in the late-1960s and early 1970s, the LS7's size was rounded down to 427 cubic inches. Official output was 505 bhp (377 kW) and has a 0-60 mph (97 km/h) time of 3.7 seconds. Top speed is 198 mph (319 km/h).[75] Another first for a Corvette, the Z06 featured a full aluminum chasis. The frame mirrored the C5/6 architecture but substituting aluminum hydroformed rails and aluminum extrustions and castings fore and aft. This dropped weight from 419 to 287 pounds while improving chassis stiffness.[76]

For 2008, the Corvette received a mild freshening: a new LS3 engine with displacement increased to 6.2 L (380 cu in), resulting in 430 bhp (321 kW) and 424 lb⋅ft (575 N⋅m) (436 bhp (325 kW) and 428 lb⋅ft (580 N⋅m) if ordered with the optional performance exhaust). The 6-speed manual transmission also has improved shift linkage and a 0–60 time of 4.0 seconds, while the automatic is set up for quicker shifts giving the C6 automatic a 0–60 time of 4.0 seconds, quicker than any other production automatic Corvette. The interior was slightly updated and a new 4LT leather-wrap interior package was added. The wheels were also updated to a new five-spoke design.[77]

The ZR1 was formally announced in a December 2007 press statement by General Motors, where it was revealed that their target of 100 bhp (75 kW) per 1 L (61 cu in) had been reached by a new "LS9" engine with an Eaton-supercharged 6.2-liter engine producing 638 bhp (476 kW) and 604 lb⋅ft (819 N⋅m). The LS9 engine was the most powerful to be put into a GM production sports car.[78] Its top speed was 205 mph (330 km/h).[79]

The historical name Grand Sport returned to the Corvette lineup in 2010 as an entirely new model series that replaced the Z51 option. The new model was basically an LS3 equipped Z06 with a steel frame instead of aluminum. It retained many of the features of the Z06 including a wide body with 18x9.5 and 19x12 inch wheels, dry sump oiling (manual transmission coupes only), 6-piston 14" front brakes and 4-piston rear, and improved suspension.[50] Manual transmission-equipped G/S coupe models received a tweaked LS3 with a forged crank, are built in Z06 fashion by hand, and utilize a dry-sump oil system. The first three gears were also made shorter for better throttle response and faster acceleration.[80] A new launch control system was introduced for all models that allows for sub-4-second 0–60. EPA is estimated 26 MPG highway, 1.0 G on skid pad.[21]

Beginning with the 2011 model year, buyers of the Corvette Z06 and ZR1 were offered the opportunity to assist in the build of their engine. Titled the "Corvette Engine Build Experience," buyers paid extra to be flown to the Wixom, Michigan Performance Build Center.[81] Participants helped the assembly line workers build the V8 engine, then took delivery of the car at the National Corvette Museum in Bowling Green, KY, near the Corvette final assembly point.[82]

The last C6 Corvette was manufactured in February 2013.[83][84] In May 2013, a federal investigation of problems with more than 100,000 C6 lighting systems was announced.[85]

2014 Corvette Stingray coupe

2014 Corvette Stingray convertible

2019 Corvette ZR1

Development for the seventh generation Corvette started in 2007. Originally set to be introduced for the 2011 model year, its introduction was delayed for three years. It was finally released for the 2014 model year.[86] Mid-engine and rear-engine layouts had been considered, but the front-engine, rear-wheel drive (RWD) platform was chosen to keep production costs lower.[87]

To GM's product planners and marketers, the fact that the Corvette had become known as an "old man's toy" became a prime factor in developing the next generation. Studies showed that about 46 percent of Corvette buyers in 2012, through October, were 55 or older, compared with 22 percent of Audi R8 and 30 percent of Porsche 911 customers. The head of Chevy marketing, Chris Perry, acknowledges that too many people saw it as the car of "the successful plumber." John Fitzpatrick, Corvette's marketing manager said "It's the old saying, 'Nobody wants to be seen driving an old man's car, but everybody wants to be seen driving a young man's car.' "[49] To counter that perception GM planned to make the new generation C7 more aspirational to younger people. Towards that end, a camouflaged version of the car was made available in the popular video game Gran Turismo 5 in November 2012.[88] As part of the marketing effort associated with the introduction of the new generation, the 2013 Indianapolis 500 utilized a Corvette for the 12th time as its pace car.

The Motley Fool reports that Chevrolet could be earning $10,000 or more in gross profit for every Corvette it sells.[89] GM's profit on sales is separate from the profits made by the individual dealerships selling the cars to the public.

The 2014 Chevrolet Corvette includes an LT1 6.2 L V8 (376 cu in) making 455 bhp (339 kW) or 460 bhp (340 kW) with the optional performance exhaust. The LT1 engine (the "LT1" designation was first used by GM in 1970 and then later in 1992.) is in the Gen V family of small block engines, which will be used in GM vehicles as the new small V8 option. It features three advanced technologies to the new LT1 V8 engine: direct injection, variable valve timing, and an active fuel management system.[90] Fuel injectors are located under the intake manifold. The Corvette remains rear-wheel drive with the transaxle located in the rear. Transmission choices include a 7-speed manual or a 6-speed (2014) / 8-speed (2015-) automatic with paddle shifters. The new interior includes wide-bottom seats as standard, with sportier versions with high side bolsters optional. The Corvette's flag logo has been revised for the new car and a small casting of a stingray has been added to the car's ornamentation.

Features of the new generation's structure include a carbon fiber hood and removable roof panel. The fenders, doors and rear quarter panels remain composite. At the rear of the car, the trademark round taillights have changed to a more squarish form. The underbody panels are made of "carbon-nano" composite and it makes use of a new aluminum frame which locates the four wheels an inch farther apart, front to rear and side to side. Luggage space decreased by 33% from the previous generation's.[91] The overall weight of the car was not announced by General Motors for many months after its first showing in January 2013. Despite the increased use of aluminum and other light weight materials, numerous publications reported that the weight would remain essentially unchanged from that of the previous generation's.[92][93][94] In August, 2013, the weight of the new Corvette was reported to be 3,444 lb (1,562 kg),[95] meaning it would weigh more than the previous generation's C6 ZR1 model (3,324 lb (1,508 kg)). The ZR1 C6 weight included a supercharger and intercooler on its 6.2L engine.[96]

Chevrolet announced the C7 Z06 at the 2014 Detroit Auto Show. The 2015 Z06 Corvette has 650 bhp from the supercharged LT4 aluminum 6.2 L V8 engine.[97][98]

The new generation Corvette resurrected the "Stingray" name (originally spelled "Sting Ray" on 1963 to 1967 models and "Stingray" from 1969 to 1976), last used in 1976.[99]

For the 2015 model, Chevrolet began offering a transaxle version of the 8L90 8-speed automatic to replace the previous 6-speed 6L80.[100][101]

2017 Corvette Grand Sport Collector Edition #43

2017 Chevrolet Corvette Grand Sport Collector Edition Dash Plaque

For the 2017 model year Chevrolet once again introduced the Grand Sport (GS) model.[102] This model includes Z06 wide-body styling features and suspension tuning along with the Z51 dry sump LT1 engine configuration. Grand Sport models were available in 10 exterior colors and could have the optional Heritage Package which included hash-mark fender graphics (available in six colors. As part of the introduction of the Grand Sport in Geneva, Switzerland, Chevrolet also announced a 2017 Chevrolet Corvette Grand Sport Collector Edition that was to be limited to 1,000 vehicles in total with 850 for the US Market. Final production numbers show 784 Coupes and 151 Convertibles were built; 935 total.[103]

The $4,995 Z25 Option Package was a cosmetic upgrade that contained the following: blue fender hash-marks, two-tone blue leather seating surfaces with a logo on the seat headrest, blue leather stitching, serialized edition numbered dash plaque, and carpeted floor mats with logo,

For the 2019 model year, the ZR1 variant returned. This model features a new LT5 engine. The long block of the LT5 is the same as the LT4, but the supercharger displacement was increased from 1.7 liters to 2.65 liters. The C7 ZR1 power output is 755 horsepower.

The last C7 Corvette (also making it the last front-engined Corvette), a black Z06, was auctioned off on June 28, 2019 for $2.7 million[104] at the Barrett-Jackson Northeast auction. The auction benefited the Stephen Siller Tunnel to Towers Foundation, which helps pay off mortgages for the families of first responders that were killed in the line of duty and builds "mortgage-free, accessible smart homes" for injured service members.[105]

2020 Chevrolet Corvette

2020 Corvette rear end

The 2020 Corvette model, both coupe and convertible configurations of the base-model Stingray made their debut within a 3-month gap. The coupe made its debut on July 18, 2019, with three launch colors, red (with the Z51 Package), white, and blue while the convertible made its debut on October 2 at the Kennedy Space Center along with the C8.R race car, which took part at the 2020 Daytona 24 Hours.

The Corvette C8 is the first production Corvette to have a rear mid-engine configuration.[106] It is also GM's first rear mid-engine production car since the 1984 Pontiac Fiero. It is powered by a 6.2 liter naturally aspirated V8 called the LT2, this engine generates 495 horsepower and 470 lb/ft of torque when equipped with the Z51 performance package. The Corvette C8 convertible is the first Corvette with a retractable hardtop.[107]

In January 2020 the car became the most expensive charity vehicle sold that week at the Barrett-Jackson auction, selling for $3 million. The proceeds of the sale went to the Detroit Children's Fund.[108]

The 2021 model year received some changes from the 2020 launch year of the C8 Corvette. Long Beach Red Metallic Tintcoat and Blade Silver Metallic were retired and replaced with Red Mist Metallic Tintcoat and Silver Flare Metallic as premium color options. Additionally, full-length racing stripes saw 4 new color options. The interior for 2021 saw the addition of a 3LT trim exclusive color option of Sky Cool Gray / Strike yellow two-tone. Certain packages saw price increases. Unfulfilled 2020 order that carried over into 2021 will have to pay for the price increases in the 2021 model.[109][110]

The 2021 Corvette will start production on December 8 of 2020 due to extended production of the 2020 model year.[111]

A Corvette C5-R leading a Maserati MC12 in Oschersleben, Germany

In 1960, three C-1 Corvettes were race modified and entered in the 24 Hours of Le Mans by team owner Briggs Cunningham and which were numbered #1, #2, and #3 cars in the race. The numbered #3 car was driven by John Fitch and Bob Grossman and it had finished the race in eighth place overall, but it had won the big-bore GT class.[126]

The Chevrolet Corvette C5-R is a grand touring racing car built by Pratt & Miller and General Motors for competition in endurance racing. The car is based on the C5 generation of the Chevrolet Corvette sports car, yet is designed purely for motorsports use.[127] It became one of the most dominant cars in GT categories, with wins at the 24 Hours of Daytona, 12 Hours of Sebring, and 24 Hours of Le Mans, as well as championships in the American Le Mans Series.[128] The Corvette C5-Rs debuted in 1999 and continues to be raced to this day, although the C5-R has effectively been replaced by the Corvette C6.R.[129]

A GT1 C6.R on the back straight of Long Beach, California

C6.R GT1 (Z06) In 2005, the factory Corvette Team began racing the C6.R to coincide with the new sixth-generation (C6) Corvette being released to the public. Private teams, primarily in Europe, continued to race the C5-R for a couple of years before switching to the C6.R. Corvette C6.R went on to win its class at every race it entered in the 2005 ALMS season.[130] By the end of 2009, Corvette had clinched four consecutive ALMS GT1 team and manufacturers titles (2005–2008) and three Le Mans 24 Hour class victories in the LMGT1 category (2005, 2006, 2009). 2007 and 2008 races were won by the factory Aston Martin squad's DBR9. The last official race for factory GT1 Corvettes was the 2009 24 Hours of Le Mans.[131]

C6.R GT2 (ZR1) While some privateers continued to use GT1 version of the C6.R in Europe, the official factory team Corvette Racing switched from the slowly dying GT1 category to the much more competitive and popular GT2 class in mid-2009. The new GT2 C6.R used a modified version of the ZR1 model body, but does not have the ZR1 supercharged engine. GT2 rules are based more on production vehicles, therefore the GT2 C6.R naturally aspirated engine was considerably more restricted and less powerful than its predecessor. The car debuted at Mid-Ohio's ALMS round. They achieved one ALMS race victory in the remaining 2009 ALMS season, and one victory at the final round of 2010 ALMS season, Petit Le Mans. Corvette Racing's two GT2 C6.Rs also led most of the 2010 24 Hours of Le Mans, but both cars were forced to retire. Racing in the new GTE Pro class, the C6.R raced in the 2011 24 Hours of Le Mans with the No. 73 car taking the class victory. The No. 74 car led the class for most of the race but crashed in the morning hours. The C6.R raced by Larbre Competition also took the GTE Am class victory.[132] In 2012, Corvette Racing returned to glory in the ALMS winning 4 of 10 races and claiming the Driver's, Team, and Manufacturer's Championships. Corvette Racing repeated the feat in 2013 by winning 5 of 10 races and claiming the Driver's, Team, and Manufacturer's Championships again.

A Corvette C7.R at the 2016 Goodwood Festival of Speed

In 2014, Corvette Racing introduced the new C7.R to coincide with the launch of the seventh-generation C7 Corvette. The car made its on track debut at the 2013 Rolex Motorsports Reunion and later participated in the 2014 Roar Before the Rolex 24 to prepare for the 2014 United SportsCar Championship. The car's new livery was debuted at the 2014 North American International Auto Show. In 2015, the Corvette Racing C7.R took class victories at both the 24 Hours of Daytona and the 24 Hours of Le Mans.

In October 2019, at the Kennedy Space Center Visitor Complex, the C8.R made its surprise debut during the world premiere of the C8 Convertible. Two cars took part in the 2020 Rolex 24 at Daytona International Speedway. The cars placed 4th and 7th in the GTLM Class.

2007 Corvette Indy 500 Pace Car

A Corvette has been selected as the pace car at the Indianapolis 500, 18 times.[133] The 2008 edition of the Indy 500 represented a record fifth-consecutive year to lead the field until 2009 when the Chevrolet Camaro SS was selected. The Corvette's pace car years and details include:

• 1978 – Driven by 1960 race winner Jim Rathmann; Chevrolet produced 6,502 production replicas.
• 1986 – Driven by famed pilot Chuck Yeager; all 7,315 production convertibles were considered pace car convertibles and included official graphics (to be installed at the owner's discretion).
• 1995 – Driven by then Chevrolet General Manager Jim Perkins; 527 production replicas produced.
• 1998 – Driven by 1963 race winner Parnelli Jones when an injury prevented golfer Greg Norman from performing the duty; 1,158 production replicas produced.
• 2002 – Driven by actor Jim Caviezel; no production replicas produced but graphics were available through SPO – approximately 300 sets sold.
• 2004 – Driven by actor Morgan Freeman; no production replicas produced.
• 2005 – Driven by General Colin Powell; no production replicas produced.
• 2006 – Driven by cycling champion Lance Armstrong (prior to scandal); first Corvette Z06 pace car; no production replicas produced.
• 2007 – Driven by actor Patrick Dempsey; 500 production replicas – all convertibles.
• 2008 – Driven by Emerson Fittipaldi; 500 production replicas – coupes and convertibles.
• 2012 – Driven by Guy Fieri; first Corvette C6 ZR1 pace car; no production replicas produced.
• 2013 – Driven by Jim Harbaugh; first year of production for C7 generation.
• 2015 – Driven by Jeff Gordon; first Chevrolet Corvette C7 Z06 pace car
• 2017 – Driven by actor Jeffrey Dean Morgan; 2017 Grand Sport Convertible[134]
• 2018 - Driven by professional basketball player Victor Oladipo - Chevrolet Corvette C7 ZR1; no production replicas produced.
• 2019 - Driven by NBC Sports broadcaster Dale Earnhardt, Jr. - last year of production for C7 generation; no production replicas produced.
• 2020 - Driven by GM President Mark Reuss > 2020 Corvette Stingray Torch Red Coupe is the Official Pace Car for the 104th Indianapolis 500 on August 23 > no production replicas produced.