Fuel pump

Mechanical fuel pump, fitted to cylinder head

Prior to the widespread adoption of electronic fuel injection, most carbureted automobile engines used mechanical fuel pumps to transfer fuel from the fuel tank into the fuel bowls of the carburetor. The two most widely used fuel feed pumps are diaphragm and plunger-type mechanical pumps. Diaphragm pumps are a type of positive displacement pump. Diaphragm pumps contain a pump chamber whose volume is increased or decreased by the flexing of a flexible diaphragm, similar to the action of a piston pump. A check valve is located at both the inlet and outlet ports of the pump chamber to force the fuel to flow in one direction only. Specific designs vary, but in the most common configuration, these pumps are typically bolted onto the engine block or head, and the engine's camshaft has an extra eccentric lobe that operates a lever on the pump, either directly or via a pushrod, by pulling the diaphragm to bottom dead center. In doing so, the volume inside the pump chamber increased, causing pressure to decrease. This allows fuel to be pushed into the pump from the tank (caused by atmospheric pressure acting on the fuel in the tank). The return motion of the diaphragm to top dead center is accomplished by a diaphragm spring, during which the fuel in the pump chamber is squeezed through the outlet port and into the carburetor. The pressure at which the fuel is expelled from the pump is thus limited (and therefore regulated) by the force applied by the diaphragm spring.

The carburetor typically contains a float bowl into which the expelled fuel is pumped. When the fuel level in the float bowl exceeds a certain level, the inlet valve to the carburetor will close, preventing the fuel pump from pumping more fuel into the carburetor. At this point, any remaining fuel inside the pump chamber is trapped, unable to exit through the inlet port or outlet port. The diaphragm will continue to allow pressure to the diaphragm, and during the subsequent rotation, the eccentric will pull the diaphragm back to bottom dead center, where it will remain until the inlet valve to the carburetor reopens.

Because one side of the pump diaphragm contains fuel under pressure and the other side is connected to the crankcase of the engine, if the diaphragm splits (a common failure), it can leak fuel into the crankcase. The capacity of both mechanical and electric fuel pump is measured in psi (which stands for pounds per square inch). Usually, this unit is the general measurement for pressure, yet it has slightly different meaning, when talking about fuel pumps.

Diagram of diaphragm type fuel pump

A piston metering pump f.e. gasoline – or additive metering pump

In modern cars the fuel pump is usually electric and located inside the fuel tank. The pump creates a higher pressure in the fuel lines, pushing the gasoline to the engine. The higher pressure raises the boiling point of the gasoline. Placing the pump in the tank puts the component least likely to handle gasoline vapor well (the pump itself) farthest from the engine, submersed in cool liquid. Another benefit to placing the pump inside the tank is that it is less likely to start a fire. Though electrical components (such as a fuel pump) can spark and ignite fuel vapors, liquid fuel will not explode (see flammability limit) and therefore submerging the pump in the tank is one of the safest places to put it. In most cars, the fuel pump delivers a constant flow of gasoline to the engine; fuel not used is returned to the tank. This further reduces the chance of the fuel boiling, since it is never kept close to the hot engine for too long.

Electric fuel pump

Replacing a mechanical fuel pump with an electric one removes an accessory load from the engine and reduces the engine fuel consumption. Also, the fuel supply can be monitored more accurately by the electronic control unit (ECU). As the pump is operating continuously the engine may be shut down, at a stop-light to conserve fuel for example, but still have the necessary fuel pressure available for a quick start.

The ignition switch does not supply the current required to operate the pump; it supplies a smaller current which activates a relay which is designed for the pump operating current. It is common for the fuel pump relay to become oxidized and cease functioning; this is much more common than the fuel pump itself failing. Modern engines use solid-state control which allows the fuel pressure to be controlled with pulse-width modulation of the pump voltage. This increases the life of the pump, allows a smaller and lighter pump, and reduces the power consumed by the pump.

Cars with electronic fuel injection have an electronic control unit (ECU) and this may be programmed with safety logic that will shut the electric fuel pump off, even if the engine is running. In the event of a collision this will prevent fuel leaking from any ruptured fuel line. Additionally, cars may have an inertia switch (usually located underneath the front passenger seat) that is "tripped" in the event of an impact, or a roll-over valve that will shut off the fuel pump in case the car rolls over.

Some ECUs may also be programmed to shut off the fuel pump if they detect low or zero oil pressure which would indicate an impending mechanical failure.

The fuel sending unit may be an assembly comprising an electric fuel pump, filter, strainer, and electronic device used to measure the amount of fuel in the tank. It does this using a float attached to a sensor which sends a signal to the dash-mounted fuel gauge.

Pumps for direct-injection diesel and gasoline engines operate at a much higher pressure, up to 30,000 psi[4] and have configurations such as common rail radial piston, common rail two piston radial, inline, port and helix, and metering unit. Injection pumps are fuel lubricated which prevents oil from contaminating the fuel. Oil contamination would introduce oil-related emissions and clog injectors.[3] Many diesel engines are common rail, which means all the injectors are supplied from a common high pressure fuel pipe supplied by the fuel pump. Common rails damp pressure fluctuations caused by the intermittent opening and closing of the injectors. Common rails also make it easier for the fuel pressure to be measured by one transducer instead of one for each cylinder.[3] Port and Helix (plunger type) high pressure fuel pumps are most commonly used in marine diesels because of their simplicity, reliability, and its ability to be scaled up in proportion to the engine size.[2]

Port and Helix type pump

Port and Helix pumps are cam driven plunger type pumps that run at one-half engine rpm for four stoke engines and at the same rpm in the case of a two stroke. The pump is similar to that of a radial piston type pump but instead of a piston it has a machined plunger that has no seals. When the plunger is at top dead center, the injection to the cylinder is finished and it is returned on its downward stroke by a compression spring.[2] Because the height of the cam lobe cannot be easily changed, the amount of fuel being pumped to the injector is controlled by a rack and pinion device that rotates the plunger allowing variable amounts of fuel to the area above the plunger. Inlet and outlet ports are located on two sides of the pumps cylinder walls allowing fuel to flow through the compression chamber until the plunger is driven up closing the two ports and starting the compression motion. The outlet port feeds back into the fuel tank/settler of the engine. The fuel is then forced through a stop check valve, to prevent backflow to the injector nozzle at pressures that can exceed 18,000 psi.[3]