HDMI

HDMI uses the Consumer Electronics Association/Electronic Industries Alliance 861 standards. HDMI 1.0 to HDMI 1.2a uses the EIA/CEA-861-B video standard, HDMI 1.3 uses the CEA-861-D video standard, and HDMI 1.4 uses the CEA-861-E video standard.[6]^{(p. III)} The CEA-861-E document defines "video formats and waveforms; colorimetry and quantization; transport of compressed and uncompressed LPCM audio; carriage of auxiliary data; and implementations of the Video Electronics Standards Association (VESA) Enhanced Extended Display Identification Data Standard (E-EDID)".[39] On July 15, 2013, the CEA announced the publication of CEA-861-F, a standard that can be used by interfaces such as DVI, HDMI, and LVDS.[40] CEA-861-F adds the ability to transmit several Ultra HD video formats and additional color spaces.[40]

To ensure baseline compatibility between different HDMI sources and displays (as well as backward compatibility with the electrically compatible DVI standard) all HDMI devices must implement the sRGB color space at 8 bits per component.[6]^(§6.2.3) Ability to use the Y′C_BC_R color space and higher color depths ("deep color") is optional. HDMI permits sRGB 4:4:4 chroma subsampling (8–16 bits per component), xvYCC 4:4:4 chroma subsampling (8–16 bits per component), Y′C_BC_R 4:4:4 chroma subsampling (8–16 bits per component), or Y′C_BC_R 4:2:2 chroma subsampling (8–12 bits per component). The color spaces that can be used by HDMI are ITU-R BT.601, ITU-R BT.709-5 and IEC 61966-2-4.[6]^{(§§6.5,6.7.2)}

For digital audio, if an HDMI device has audio, it is required to implement the baseline format: stereo (uncompressed) PCM. Other formats are optional, with HDMI allowing up to 8 channels of uncompressed audio at sample sizes of 16-bit, 20-bit and 24-bit, with sample rates of 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz and 192 kHz.[6]^(§7) HDMI also carries any IEC 61937-compliant compressed audio stream, such as Dolby Digital and DTS, and up to 8 channels of one-bit DSD audio (used on Super Audio CDs) at rates up to four times that of Super Audio CD.[6]^(§7) With version 1.3, HDMI allows lossless compressed audio streams Dolby TrueHD and DTS-HD Master Audio.[6]^(§7) As with the Y′C_BC_R video, audio capability is optional. Audio return channel (ARC) is a feature introduced in the HDMI 1.4 standard.[41] "Return" refers to the case where the audio comes from the TV and can be sent "upstream" to the AV receiver using the HDMI cable connected to the AV receiver.[41] An example given on the HDMI website is that a TV that directly receives a terrestrial/satellite broadcast, or has a video source built in, sends the audio "upstream" to the AV receiver.[41]

The HDMI standard was not designed to pass closed caption data (for example, subtitles) to the television for decoding.[42] As such, any closed caption stream must be decoded and included as an image in the video stream(s) prior to transmission over an HDMI cable to appear on the DTV. This limits the caption style (even for digital captions) to only that decoded at the source prior to HDMI transmission. This also prevents closed captions when transmission over HDMI is required for upconversion. For example, a DVD player that sends an upscaled 720p/1080i format via HDMI to an HDTV has no way to pass Closed Captioning data so that the HDTV can decode it, as there is no line 21 VBI in that format.

HDMI has three physically separate communication channels, which are the DDC, TMDS and the optional CEC.[6]^(§8.1) HDMI 1.4 added ARC and HEC.[41][43]

The Display Data Channel (DDC) is a communication channel based on the I²C bus specification. HDMI specifically requires the device implement the Enhanced Display Data Channel (E-DDC), which is used by the HDMI source device to read the E-EDID data from the HDMI sink device to learn what audio/video formats it can take.[6]^{(§§8.1,CEC-1.2–CEC-1.3)} HDMI requires that the E-DDC implement I²C standard mode speed (100 kbit/s) and allows it to optionally implement fast mode speed (400 kbit/s).[6]^(§4.2.8)

The DDC channel is actively used for High-bandwidth Digital Content Protection (HDCP).

Transition-minimized differential signaling (TMDS) on HDMI interleaves video, audio and auxiliary data using three different packet types, called the Video Data Period, the Data Island Period and the Control Period. During the Video Data Period, the pixels of an active video line are transmitted. During the Data Island period (which occurs during the horizontal and vertical blanking intervals), audio and auxiliary data are transmitted within a series of packets. The Control Period occurs between Video and Data Island periods.[6]^(§5.1.2)

Both HDMI and DVI use TMDS to send 10-bit characters that are encoded using 8b/10b encoding that differs from the original IBM form for the Video Data Period and 2b/10b encoding for the Control Period. HDMI adds the ability to send audio and auxiliary data using 4b/10b encoding for the Data Island Period. Each Data Island Period is 32 pixels in size and contains a 32-bit Packet Header, which includes 8 bits of BCH ECC parity data for error correction and describes the contents of the packet. Each packet contains four subpackets, and each subpacket is 64 bits in size, including 8 bits of BCH ECC parity data, allowing for each packet to carry up to 224 bits of audio data. Each Data Island Period can contain up to 18 packets. Seven of the 15 packet types described in the HDMI 1.3a specifications deal with audio data, while the other 8 types deal with auxiliary data. Among these are the General Control Packet and the Gamut Metadata Packet. The General Control Packet carries information on AVMUTE (which mutes the audio during changes that may cause audio noise) and Color Depth (which sends the bit depth of the current video stream and is required for deep color). The Gamut Metadata Packet carries information on the color space being used for the current video stream and is required for xvYCC.[6]^{(§§5.2–5.3,6.5.3,6.7.2,6.7.3)}

Consumer Electronics Control (CEC) is an HDMI feature designed to allow the user to command and control up to 15 CEC-enabled devices, that are connected through HDMI,[44][45] by using only one of their remote controls (for example by controlling a television set, set-top box, and DVD player using only the remote control of the TV). CEC also allows for individual CEC-enabled devices to command and control each other without user intervention.[6]^(§CEC-3.1)

It is a one-wire bidirectional serial bus that is based on the CENELEC standard AV.link protocol to perform remote control functions.[46] CEC wiring is mandatory, although implementation of CEC in a product is optional.[6]^(§8.1) It was defined in HDMI Specification 1.0 and updated in HDMI 1.2, HDMI 1.2a and HDMI 1.3a (which added timer and audio commands to the bus).[6]^{(§§CEC-1.2,CEC-1.3,CEC-3.1,CEC-5)} USB to CEC adapters exist that allow a computer to control CEC-enabled devices.[47][48][49][50]

Introduced in HDMI 1.4, HDMI Ethernet and Audio Return Channel (HEAC) adds a high-speed bidirectional data communication link (HEC) and the ability to send audio data upstream to the source device (ARC). HEAC utilizes two lines from the connector: the previously unused Reserved pin (called HEAC+) and the Hot Plug Detect pin (called HEAC−).[51]^(§HEAC-2.1) If only ARC transmission is required, a single mode signal using the HEAC+ line can be used, otherwise, HEC is transmitted as a differential signal over the pair of lines, and ARC as a common mode component of the pair.[51]^(§HEAC-2.2)

Audio Return Channel (ARC)

ARC is an audio link meant to replace other cables between the TV and the A/V receiver or speaker system.[41] This direction is used when the TV is the one that generates or receives the video stream instead of the other equipment.[41] A typical case is the running of an app on a smart TV such as Netflix, but reproduction of audio is handled by the other equipment.[41] Without ARC, the audio output from the TV must be routed by another cable, typically TOSLink or coax, into the speaker system.[41][52]

HDMI Ethernet Channel (HEC)

HDMI Ethernet Channel technology consolidates video, audio, and data streams into a single HDMI cable, and the HEC feature enables IP-based applications over HDMI and provides a bidirectional Ethernet communication at 100 Mbit/s.[43] The physical layer of the Ethernet implementation uses a hybrid to simultaneously send and receive attenuated 100BASE-TX-type signals through a single twisted pair.[52][53]

An adapter with HDMI (male, right) and DVI (female, left) connectors

An adapter with DVI (female, rear, not visible) and HDMI (female, front) connectors

HDMI is backward compatible with single-link Digital Visual Interface digital video (DVI-D or DVI-I, but not DVI-A or dual-link DVI). No signal conversion is required when an adapter or asymmetric cable is used, so there is no loss of video quality.[6]^{(appx. C)}

From a user's perspective, an HDMI display can be driven by a single-link DVI-D source, since HDMI and DVI-D define an overlapping minimum set of allowed resolutions and frame-buffer formats to ensure a basic level of interoperability. In the reverse case, a DVI-D monitor has the same level of basic interoperability unless content protection with High-bandwidth Digital Content Protection (HDCP) interferes—or the HDMI color encoding is in component color space Y′C_BC_R instead of RGB, which is not possible in DVI. An HDMI source, such as a Blu-ray player, may require an HDCP-compliant display, and refuse to output HDCP-protected content to a non-compliant display.[54] A further complication is that there is a small amount of display equipment, such as some high-end home theater projectors, designed with HDMI inputs but not HDCP-compliant.

Any DVI-to-HDMI adapter can function as an HDMI-to-DVI adapter (and vice versa).[55] Typically, the only limitation is the gender of the adapter's connectors and the gender of the cables and sockets it is used with.

Features specific to HDMI, such as remote-control and audio transport, are not available in devices that use legacy DVI-D signalling. However, many devices output HDMI over a DVI connector (e.g., ATI 3000-series and NVIDIA GTX 200-series video cards),[6]^{(appx. C)}[56] and some multimedia displays may accept HDMI (including audio) over a DVI input. Exact capabilities beyond basic compatibility vary. Adapters are generally bi-directional.

High-bandwidth Digital Content Protection (HDCP) is a newer form of digital rights management. Intel created the original technology to make sure that digital content followed the guidelines set by the Digital Content Protection group.

HDMI can use HDCP to encrypt the signal if required by the source device. CSS, CPRM and AACS require the use of HDCP on HDMI when playing back encrypted DVD Video, DVD Audio, HD DVD and Blu-ray Disc. The HDCP Repeater bit controls the authentication and switching/distribution of an HDMI signal. According to HDCP Specification 1.2 (beginning with HDMI CTS 1.3a), any system that implements HDCP must do so in a fully compliant manner. HDCP testing that was previously only a requirement for optional tests such as the "Simplay HD" testing program is now part of the requirements for HDMI compliance.[6]^(§9.2)[57][58] HDCP accommodates up to 127 connected devices with up to 7 levels, using a combination of sources, sinks and repeaters.[59] A simple example of this is several HDMI devices connected to an HDMI AV receiver that is connected to an HDMI display.[59]

Devices called HDCP strippers can remove the HDCP information from the video signal so the video can play on non-HDCP-compliant displays,[60] though a fair use and non-disclosure form must usually be signed with a registering agency before use.

Connector types for HDMI

HDMI connector plugs (male): Type D (Micro), Type C (Mini), and Type A

HDMI type A receptacle

There are five HDMI connector types. Type A/B are defined in the HDMI 1.0 specification, type C is defined in the HDMI 1.3 specification, and type D/E are defined in the HDMI 1.4 specification.

Type A

The plug (male) connector outside dimensions are 13.9 mm × 4.45 mm, and the receptacle (female) connector inside dimensions are 14 mm × 4.55 mm.[6]^(§4.1.9.2) There are 19 pins, with bandwidth to carry all SDTV, EDTV, HDTV, UHD, and 4K modes.[6]^(§6.3) It is electrically compatible with single-link DVI-D.[6]^(§4.1.3)

Type B

This connector is 21.2 mm × 4.45 mm and has 29 pins, carrying six differential pairs instead of three, for use with very high-resolution displays such as WQUXGA (3840×2400). It is electrically compatible with dual-link DVI-D, but has not yet been used in any products.[61] With the introduction of HDMI 1.3, the maximum bandwidth of single-link HDMI exceeded that of dual-link DVI-D. As of HDMI 1.4, the pixel clock rate crossover frequency from single to dual-link has not been defined.[51]^{(§§4.1.3,4.1.9.4)}

Type C

This Mini connector is smaller than the type A plug, measuring 10.42 mm × 2.42 mm but has the same 19-pin configuration.[6]^{(§§4.1.9.4,4.1.9.6)} It is intended for portable devices.[4][6]^(§4.1.1)[62] The differences are that all positive signals of the differential pairs are swapped with their corresponding shield, the DDC/CEC Ground is assigned to pin 13 instead of pin 17, the CEC is assigned to pin 14 instead of pin 13, and the reserved pin is 17 instead of pin 14.[6]^(§4.1.10.5) The type C Mini connector can be connected to a type A connector using a type A-to-type C cable.[6]^(§4.1.1)[62]

Micro HDMI receptacle

Type D

This Micro connector shrinks the connector size to something resembling a micro-USB connector,[62][63][64] measuring only 5.83 mm × 2.20 mm[65]^{(fig. 4.1.9.8)} For comparison, a micro-USB connector is 6.85 mm × 1.8 mm and a USB Type-A connector is 11.5 mm × 4.5 mm. It keeps the standard 19 pins of types A and C, but the pin assignment is different from both.[66]

Type E

The Automotive Connection System[67] has a locking tab to keep the cable from vibrating loose and a shell to help prevent moisture and dirt from interfering with the signals. A relay connector is available for connecting standard consumer cables to the automotive type.[68]

The HDMI alternate mode lets a user connect the reversible USB-C connector with the HDMI source devices (mobile, tablet, laptop). This cable connects to video display/sink devices using any of the native HDMI connectors. This is an HDMI cable, in this case a USB-C to HDMI cable.[69]

A standard HDMI cable

An HDMI cable is composed of four shielded twisted pairs, with impedance of the order of 100 Ω (±15%), plus seven separate conductors. HDMI cables with Ethernet differ in that three of the separate conductors instead form an additional shielded twisted pair (with the CEC/DDC ground as a shield).[51]^(§HEAC-2.9)

Although no maximum length for an HDMI cable is specified, signal attenuation (dependent on the cable's construction quality and conducting materials) limits usable lengths in practice[70][71] and certification is difficult to achieve for lengths beyond 13 m.[72] HDMI 1.3 defines two cable categories: Category 1-certified cables, which have been tested at 74.25 MHz (which would include resolutions such as 720p60 and 1080i60), and Category 2-certified cables, which have been tested at 340 MHz (which would include resolutions such as 1080p60 and 4K30).[6]^(§4.2.6)[63][73] Category 1 HDMI cables are marketed as "Standard" and Category 2 HDMI cables as "High Speed".[4] This labeling guideline for HDMI cables went into effect on October 17, 2008.[74][75] Category 1 and 2 cables can either meet the required parameter specifications for inter-pair skew, far-end crosstalk, attenuation and differential impedance, or they can meet the required non-equalized/equalized eye diagram requirements.[6]^(§4.2.6) A cable of about 5 meters (16 feet) can be manufactured to Category 1 specifications easily and inexpensively by using 28 AWG (0.081 mm²) conductors.[70] With better quality construction and materials, including 24 AWG (0.205 mm²) conductors, an HDMI cable can reach lengths of up to 15 meters (49 feet).[70] Many HDMI cables under 5 meters of length that were made before the HDMI 1.3 specification can work as Category 2 cables, but only Category 2-tested cables are guaranteed to work for Category 2 purposes.[76]

As of the HDMI 1.4 specification, the following cable types are defined for HDMI in general:[77][78]

• Standard HDMI Cable – up to 1080i and 720p
• Standard HDMI Cable with Ethernet
• Standard Automotive HDMI Cable
• High Speed HDMI Cable – 1080p, 4K 30 Hz, 3D and deep color
• High Speed HDMI Cable with Ethernet

A new certification program was introduced in October 2015 to certify that cables work at the 18 Gbit/s maximum bandwidth of the HDMI 2.0 specification.[79] In addition to expanding the set of cable testing requirements, the certification program introduces an EMI test to ensure cables minimize interference with wireless signals. These cables are marked with an anti-counterfeiting authentication label and are defined as:[80]

• Premium High Speed HDMI Cable
• Premium High Speed HDMI Cable with Ethernet

In conjunction with the HDMI 2.1 specification, a third category of cable was announced on January 4, 2017, called "48G".[81] Also known as Category 3 HDMI or "Ultra High Speed" HDMI, the cable is designed to support the 48 Gbit/s bandwidth of HDMI 2.1, supporting 4K, 5K, 8K and 10K at 120 Hz.[82] The cable is backwards compatible with the earlier HDMI devices, using existing HDMI type A, C and D connectors, and includes HDMI Ethernet.

• Ultra High Speed HDMI Cable (48G Cable) – 4K, 5K, 8K and 10K at 120 Hz

An HDMI extender is a single device (or pair of devices) powered with an external power source or with the 5V DC from the HDMI source.[83][84][85] Long cables can cause instability of HDCP and blinking on the screen, due to the weakened DDC signal that HDCP requires. HDCP DDC signals must be multiplexed with TMDS video signals to comply with HDCP requirements for HDMI extenders based on a single Category 5/Category 6 cable.[86][87] Several companies offer amplifiers, equalizers and repeaters that can string several standard HDMI cables together. Active HDMI cables use electronics within the cable to boost the signal and allow for HDMI cables of up to 30 meters (98 feet);[83] those based on HDBaseT can extend to 100 meters; HDMI extenders that are based on dual Category 5/Category 6 cable can extend HDMI to 250 meters (820 feet); while HDMI extenders based on optical fiber can extend HDMI to 300 meters (980 feet).[84][85]

The HDMI specification is not an open standard; manufacturers need to be licensed by HDMI LLC in order to implement HDMI in any product or component. Companies who are licensed by HDMI LLC are known as HDMI Adopters.[88]

DVI is the only interface that does not require a license for interfacing HDMI.

While earlier versions of HDMI specs are available to the public for download, only Adopters have access to the latest standards (HDMI 1.4/1.4a/2).

• Only Adopters have access to the Compliance Test Specification (CTS) that is used for compliance and certification

This is required before any HDMI product can be legally sold.

• Adopters have IP rights
• Adopters receive the right to use HDMI logos and TMs on their products and marketing materials
• Adopters are listed on the HDMI website
• Products from Adopters are listed and marketed in the official HDMI product finder database
• Adopters receive more exposure through combined marketing, such as the annual HDMI Developers Conference and technology seminars

There are 2 annual fee structures associated with being an HDMI Adopter:

• High-volume (more than 10,000 units) HDMI Adopter Agreement – US$10k/year[89]
• Low-volume (10,000 units or fewer) HDMI Adopter Agreement – US$5k/year + flat US$1/unit administration fee[89]

The annual fee is due upon the execution of the Adopter Agreement, and must be paid on the anniversary of this date each year thereafter.

The royalty fee structure is the same for all volumes. The following variable per-unit royalty is device-based and not dependent on number of ports, chips or connectors:

• US$0.15 – for each end-user licensed product[89]
• US$0.05 – if the HDMI logo is used on the product and promotional material, the per-unit fee drops from US$0.15 to US$0.05.[89]
• US$0.04 – if HDCP is implemented and HDMI logo is used, the per-unit fee drops from US$0.05 to US$0.04[89]

Use of HDMI logo requires compliance testing. Adopters must license HDCP separately.

The HDMI royalty is only payable on Licensed Products that will be sold on a stand-alone basis (i.e. that are not incorporated into another Licensed Product that is subject to an HDMI royalty). For example, if a cable or IC is sold to an Adopter who then includes it in a television subject to a royalty, then the cable or IC maker would not pay a royalty, and the television manufacturer would pay the royalty on the final product. If the cable is sold directly to consumers, then the cable would be subject to a royalty.[89]

HDMI 1.0 was released on December 9, 2002, and is a single-cable digital audio/video connector interface. The link architecture is based on DVI, using exactly the same video transmission format but sending audio and other auxiliary data during the blanking intervals of the video stream. HDMI 1.0 allows a maximum TMDS clock of 165 MHz (4.95 Gbit/s bandwidth per link), the same as DVI. It defines two connectors called Type A and Type B, with pinouts based on the Single-Link DVI-D and Dual-Link DVI-D connectors respectively, though the Type B connector was never used in any commercial products. HDMI 1.0 uses TMDS encoding for video transmission, giving it 3.96 Gbit/s of video bandwidth (1920 × 1080 or 1920 × 1200 at 60 Hz) and 8-channel LPCM/192 kHz/24-bit audio. HDMI 1.0 requires support for RGB video, with optional support for Y′C_BC_R 4:4:4 and 4:2:2 (mandatory if the device has support for Y′C_BC_R on other interfaces). Color depth of 10 bpc (30 bit/px) or 12 bpc (36 bit/px) is allowed when using 4:2:2 subsampling, but only 8 bpc (24 bit/px) color depth is permitted when using RGB or Y′C_BC_R 4:4:4. Only the Rec. 601 and Rec. 709 color spaces are supported. HDMI 1.0 allows only specific pre-defined video formats, including all the formats defined in EIA/CEA-861-B and some additional formats listed in the HDMI Specification itself. All HDMI sources/sinks must also be capable of sending/receiving native Single-Link DVI video and be fully compliant with the DVI Specification.[95]

HDMI 1.1 was released on May 20, 2004, and added support for DVD-Audio.

HDMI 1.2 was released on August 8, 2005, and added the option of One Bit Audio, used on Super Audio CDs, at up to 8 channels. To make HDMI more suitable for use on PC devices, version 1.2 also removed the requirement that only explicitly supported formats be used. It added the ability for manufacturers to create vendor-specific formats, allowing any arbitrary resolution and refresh rate rather than being limited to a pre-defined list of supported formats. In addition, it added explicit support for several new formats including 720p at 100 and 120 Hz and relaxed the pixel format support requirements so that sources with only native RGB output (PC sources) would not be required to support Y′C_BC_R output.[96]^(§6.2.3)

HDMI 1.2a was released on December 14, 2005 and fully specifies Consumer Electronic Control (CEC) features, command sets and CEC compliance tests.[96]

HDMI 1.3 was released on June 22, 2006, and increased the maximum TMDS clock to 340 MHz (10.2 Gbit/s).[6][38][97] Like previous versions, it uses TMDS encoding, giving it a maximum video bandwidth of 8.16 Gbit/s (1920 × 1080 at 120 Hz or 2560 × 1440 at 60 Hz). It added support for 10 bpc, 12 bpc, and 16 bpc color depth (30, 36, and 48 bit/px), called deep color. It also added support for the xvYCC color space, in addition to the Rec. 601 and Rec. 709 color spaces supported by previous versions, and added the ability to carry metadata defining color gamut boundaries. It also optionally allows output of Dolby TrueHD and DTS-HD Master Audio streams for external decoding by AV receivers.[98] It incorporates automatic audio syncing (audio video sync) capability.[38] It defined cable Categories 1 and 2, with Category 1 cable being tested up to 74.25 MHz and Category 2 being tested up to 340 MHz.[6]^(§4.2.6) It also added the new type C Mini connector for portable devices.[6]^(§4.1.1)[99]

HDMI 1.3a was released on November 10, 2006, and had Cable and Sink modifications for type C, source termination recommendations, and removed undershoot and maximum rise/fall time limits. It also changed CEC capacitance limits, and CEC commands for timer control were brought back in an altered form, with audio control commands added. It also added the optional ability to stream SACD in its bitstream DST format rather than uncompressed raw DSD.[6]

HDMI 1.4 with audio return channel

HDMI 1.4 was released on June 5, 2009, and first came to market after Q2 of 2009.[63][100][101] Retaining the bandwidth of the previous version, HDMI 1.4 added support for 4096 × 2160 at 24 Hz, 3840 × 2160 at 24, 25, and 30 Hz, and 1920 × 1080 at 120 Hz.[65]^(§6.3.2) It also added an HDMI Ethernet Channel (HEC) that accommodates a 100 Mbit/s Ethernet connection between the two HDMI connected devices so they can share an Internet connection,[43] introduced an audio return channel (ARC),[41] 3D Over HDMI, a new Micro HDMI Connector, an expanded set of color spaces with the addition of sYCC601, Adobe RGB and Adobe YCC601, and an Automotive Connection System.[63][102][103][104][105] HDMI 1.4 defined several stereoscopic 3D formats including field alternative (interlaced), frame packing (a full resolution top-bottom format), line alternative full, side-by-side half, side-by-side full, 2D + depth, and 2D + depth + graphics + graphics depth (WOWvx).[62][106][107] HDMI 1.4 requires that 3D displays implement the frame packing 3D format at either 720p50 and 1080p24 or 720p60 and 1080p24.[107] High Speed HDMI cables as defined in HDMI 1.3 work with all HDMI 1.4 features except for the HDMI Ethernet Channel, which requires the new High Speed HDMI Cable with Ethernet defined in HDMI 1.4.[62][106][107]

HDMI 1.4a was released on March 4, 2010, and added two mandatory 3D formats for broadcast content, which was deferred with HDMI 1.4 pending the direction of the 3D broadcast market.[108][109] HDMI 1.4a has defined mandatory 3D formats for broadcast, game, and movie content.[108] HDMI 1.4a requires that 3D displays implement the frame packing 3D format at either 720p50 and 1080p24 or 720p60 and 1080p24, side-by-side horizontal at either 1080i50 or 1080i60, and top-and-bottom at either 720p50 and 1080p24 or 720p60 and 1080p24.[109]

HDMI 1.4b was released on October 11, 2011,[110] containing only minor clarifications to the 1.4a document. HDMI 1.4b is the last version of the standard that HDMI Licensing, LLC is responsible for. All future versions of the HDMI Specification were produced by the HDMI Forum, created on October 25, 2011.[35][111]

HDMI 2.0, referred to by some manufacturers as HDMI UHD, was released on September 4, 2013.[112]

HDMI 2.0 increases the maximum bandwidth to 18.0 Gbit/s.[112][113][114] HDMI 2.0 uses TMDS encoding for video transmission like previous versions, giving it a maximum video bandwidth of 14.4 Gbit/s. This enables HDMI 2.0 to carry 4K video at 60 Hz with 24 bit/px color depth.[112][115][116] Other features of HDMI 2.0 include support for the Rec. 2020 color space, up to 32 audio channels, up to 1536 kHz audio sample frequency, dual video streams to multiple users on the same screen, up to four audio streams, 4:2:0 chroma subsampling, 25 fps 3D formats, support for the 21:9 aspect ratio, dynamic synchronization of video and audio streams, the HE-AAC and DRA audio standards, improved 3D capability, and additional CEC functions.[112][117]

HDMI 2.0a was released on April 8, 2015, and added support for High Dynamic Range (HDR) video with static metadata.[118]

HDMI 2.0b was released March, 2016.[119] HDMI 2.0b initially supported the same HDR10 standard as HDMI 2.0a as specified in the CTA-861.3 specification.[117] In December 2016 additional support for HDR Video transport was added to HDMI 2.0b in the recently released CTA-861-G specification, which extends the static metadata signaling to include Hybrid Log-Gamma (HLG).[117][120][121]

HDMI 2.1 was officially announced by the HDMI Forum on January 4, 2017,[81][82] and was released on November 28, 2017.[122] It adds support for higher resolutions and higher refresh rates, including 4K 120 Hz and 8K 120 Hz. HDMI 2.1 also introduces a new HDMI cable category called Ultra High Speed (referred to as 48G during development), which certifies cables at the new higher speeds that these formats require. Ultra High Speed HDMI cables are backwards compatible with older HDMI devices, and older cables are compatible with new HDMI 2.1 devices, though the full 48 Gbit/s bandwidth is not possible without the new cables.

Additional features of HDMI 2.1:[123][122]

• Maximum supported format is 10K at 120 Hz
• Dynamic HDR for specifying HDR metadata on a scene-by-scene or even a frame-by-frame basis
• Display Stream Compression (DSC) 1.2 is used for video formats higher than 8K with 4:2:0 chroma subsampling
• High Frame Rate (HFR) for 4K, 8K, and 10K, which adds support for refresh rates up to 120 Hz
• Enhanced Audio Return Channel (eARC) for object-based audio formats such as Dolby Atmos and DTS:X
• Enhanced refresh rate and latency reduction features:
  • Variable Refresh Rate (VRR) reduces or eliminates lag, stutter and frame tearing for more fluid motion in games
  • Quick Media Switching (QMS) for movies and video eliminates the delay that can result in blank screens before content begins to be displayed
  • Quick Frame Transport (QFT) reduces latency by bursting individual pictures across the HDMI link as fast as possible when the link's hardware supports more bandwidth than the minimum amount needed for the resolution and frame rate of the content. With QFT, individual pictures arrive earlier and some hardware blocks can be fully powered off for longer periods of time between pictures to reduce heat generation and extend battery life.
• Auto Low Latency Mode (ALLM) – When a display device supports the option to either optimize its pixel processing for best latency or best pixel processing, ALLM allows the current HDMI source device to automatically select, based on its better understanding of the nature of its own content, which mode the user would most likely prefer.

Video formats that require more bandwidth than 18.0 Gbit/s (4K 60 Hz 8 bpc RGB), such as 4K 60 Hz 10 bpc (HDR), 4K 120 Hz, and 8K 60 Hz, may require the new "Ultra High Speed" or "Ultra High Speed with Ethernet" cables.[82] HDMI 2.1's other new features are supported with existing HDMI cables.

The increase in maximum bandwidth is achieved by increasing both the bitrate of the data channels and the number of channels. Previous HDMI versions use three data channels (each operating at up to 6.0 GHz in HDMI 2.0, or up to 3.4 GHz in HDMI 1.4), with an additional channel for the TMDS clock signal, which runs at a fraction of the data channel speed (one tenth the speed, or up to 340 MHz, for signaling rates up to 3.4 GHz; one fortieth the speed, or up to 150 MHz, for signaling rates between 3.4 and 6.0 GHz). HDMI 2.1 doubles the signaling rate of the data channels to 12 GHz (12 Gbit/s). The structure of the data has been changed to use a new packet-based format with an embedded clock signal, which allows what was formerly the TMDS clock channel to be used as a fourth data channel instead, increasing the signaling rate across that channel to 12 GHz as well. These changes increase the aggregate bandwidth from 18.0 Gbit/s (3 × 6.0 Gbit/s) to 48.0 Gbit/s (4 × 12.0 Gbit/s), a 2.66x improvement in bandwidth. In addition, the data is transmitted more efficiently by using a 16b/18b encoding scheme, which uses a larger percentage of the bandwidth for data rather than DC balancing compared to the TMDS scheme used by previous versions (88.8% compared to 80%). This, in combination with the 2.66x bandwidth, raises the maximum data rate of HDMI 2.1 from 14.4 Gbit/s to 42.66 Gbit/s, approximately 2.96x the data rate of HDMI 2.0.[124][125]

The 48 Gbit/s bandwidth provided by HDMI 2.1 is enough for 8K resolution at approximately 50 Hz, with 8 bpc RGB or Y′C_BC_R 4:4:4 color. To achieve even higher formats, HDMI 2.1 can use Display Stream Compression with a compression ratio of up to 3:1. Using DSC, formats up to 8K (7680 × 4320) 120 Hz or 10K (10240 × 4320) 100 Hz at 8 bpc RGB/4:4:4 are possible. Using Y′C_BC_R with 4:2:2 or 4:2:0 chroma subsampling in combination with DSC can allow for even higher formats.[123]

HDMI 2.1 includes HDR10+ as part of Vendor Specific Data Block with OUI 90-84-8b for "HDR10+ Technologies, LLC".[126][127]

The "version" of a connection depends on the versions of the HDMI ports on the source and sink devices, not on the HDMI cable. The different categories of HDMI cable only affect the bandwidth (maximum resolution / refresh rate) of the connection. Other features such as audio, 3D, chroma subsampling, or variable refresh rate depend only on the versions of the ports, and are not affected by what type of HDMI cable is used. The only exception to this is Ethernet-over-HDMI, which requires an "HDMI with Ethernet" cable.

Products are not required to implement all features of a version to be considered compliant with that version, as most features are optional. For example, displays with HDMI 1.4 ports do not necessarily support the full 340 MHz TMDS clock allowed by HDMI 1.4; they are commonly limited to lower speeds such as 300 MHz (1080p 120 Hz) or even as low as 165 MHz (1080p 60 Hz) at the manufacturer's discretion, but are still considered HDMI 1.4-compliant. Likewise, features like 10 bpc (30 bit/px) color depth may also not be supported, even if the HDMI version allows it and the display supports it over other interfaces such as DisplayPort.[91]

Feature support will therefore vary from device to device, even within the same HDMI version.

HDMI 1.0 and 1.1 are restricted to transmitting only certain video formats,[95]^(§6.1) defined in EIA/CEA-861-B and in the HDMI Specification itself.[95]^(§6.3) HDMI 1.2 and all later versions allow any arbitrary resolution and frame rate (within the bandwidth limit). Formats that are not supported by the HDMI Specification (i.e., no standardized timings defined) may be implemented as a vendor-specific format. Successive versions of the HDMI Specification continue to add support for additional formats (such as 4K resolutions), but the added support is to establish standardized timings to ensure interoperability between products, not to establish which formats are or aren't permitted. Video formats do not require explicit support from the HDMI Specification in order to be transmitted and displayed.[96]^(§6.1)

Individual products may have heavier limitations than those listed below, since HDMI devices are not required to support the maximum bandwidth of the HDMI version that they implement. Therefore, it is not guaranteed that a display will support the refresh rates listed in this table, even if the display has the required HDMI version.

Uncompressed 8 bpc (24 bit/px) color depth and RGB or Y′C_BC_R 4:4:4 color format are assumed on this table except where noted.

HDR10 requires 10 bpc (30 bit/px) color depth, which uses 25% more bandwidth than standard 8 bpc video.

Uncompressed 10 bpc color depth and RGB or Y′C_BC_R 4:4:4 color format are assumed on this table except where noted.

Blu-ray Disc and HD DVD, introduced in 2006, offer high-fidelity audio features that require HDMI for best results. HDMI 1.3 can transport Dolby Digital Plus, Dolby TrueHD, and DTS-HD Master Audio bitstreams in compressed form.[6]^(§7) This capability allows for an AV receiver with the necessary decoder to decode the compressed audio stream. The Blu-ray specification does not include video encoded with either deep color or xvYCC; thus, HDMI 1.0 can transfer Blu-ray discs at full video quality.[141]

The HDMI 1.4 specification (released in 2009) added support for 3D video and is used by all Blu-ray 3D compatible players.

The Blu-ray Disc Association (BDA) spokespersons have stated (Sept. 2014 at IFA show in Berlin, Germany) that the Blu-ray, Ultra HD players, and 4K discs are expected to be available starting in the second half to 2015. It is anticipated that such Blu-ray UHD players will be required to include a HDMI 2.0 output that supports HDCP 2.2.

Blu-ray permits secondary audio decoding, whereby the disc content can tell the player to mix multiple audio sources together before final output.[142] Some Blu-ray and HD DVD players can decode all of the audio codecs internally and can output LPCM audio over HDMI. Multichannel LPCM can be transported over an HDMI connection, and as long as the AV receiver implements multichannel LPCM audio over HDMI and implements HDCP, the audio reproduction is equal in resolution to HDMI 1.3 bitstream output. Some low-cost AV receivers, such as the Onkyo TX-SR506, do not allow audio processing over HDMI and are labelled as "HDMI pass through" devices.[143][144] Virtually all modern AV Receivers now offer HDMI 1.4 inputs and outputs with processing for all of the audio formats offered by Blu-ray Discs and other HD video sources. During 2014 several manufacturers introduced premium AV Receivers that include one, or multiple, HDMI 2.0 inputs along with a HDMI 2.0 output(s). However, not until 2015 did most major manufacturers of AV receivers also support HDCP 2.2 as needed to support certain high quality UHD video sources, such as Blu-ray UHD players.

As of 2012, most consumer camcorders, as well as many digital cameras, are equipped with a mini-HDMI connector (type C connector).

As of 2014, some cameras also have 4K capability and 3D, even some cameras costing less than US$900. It needs at least a TV/monitor with HDMI 1.4a port.[145]

Although cameras capable of HD video often include an HDMI interface for playback or even live preview, the image processor and the video processor of cameras usable for uncompressed video must be able to deliver the full image resolution at the specified frame rate in real time without any missing frames causing jitter. Therefore, usable uncompressed video out of HDMI is often called "clean HDMI".[146]

PCs with a DVI interface are capable of video output to an HDMI-enabled monitor.[6]^{(appx. C)} Some PCs include an HDMI interface and may also be capable of HDMI audio output, depending on specific hardware.[147] For example, Intel's motherboard chipsets since the 945G and NVIDIA's GeForce 8200/8300 motherboard chipsets are capable of 8-channel LPCM output over HDMI.[147][148] Eight-channel LPCM audio output over HDMI with a video card was first seen with the ATI Radeon HD 4850, which was released in June 2008 and is implemented by other video cards in the ATI Radeon HD 4000 series.[148][149][150][151][152] Linux can drive 8-channel LPCM audio over HDMI if the video card has the necessary hardware and implements the Advanced Linux Sound Architecture (ALSA).[153] The ATI Radeon HD 4000 series implements ALSA.[153][154] Cyberlink announced in June 2008 that they would update their PowerDVD playback software to allow 192 kHz/24-bit Blu-ray Disc audio decoding in Q3-Q4 of 2008.[155] Corel's WinDVD 9 Plus currently has 96 kHz/24-bit Blu-ray Disc audio decoding.[156]

Even with an HDMI output, a computer may not be able to produce signals that implement HDCP, Microsoft's Protected Video Path, or Microsoft's Protected Audio Path.[148][157] Several early graphic cards were labelled as "HDCP-enabled" but did not have the hardware needed for HDCP;[158] this included some graphic cards based on the ATI X1600 chipset and certain models of the NVIDIA Geforce 7900 series.[158] The first computer monitors that could process HDCP were released in 2005; by February 2006 a dozen different models had been released.[159][160] The Protected Video Path was enabled in graphic cards that had HDCP capability, since it was required for output of Blu-ray Disc and HD DVD video. In comparison, the Protected Audio Path was required only if a lossless audio bitstream (such as Dolby TrueHD or DTS-HD MA) was output.[148] Uncompressed LPCM audio, however, does not require a Protected Audio Path, and software programs such as PowerDVD and WinDVD can decode Dolby TrueHD and DTS-HD MA and output it as LPCM.[148][155][156] A limitation is that if the computer does not implement a Protected Audio Path, the audio must be downsampled to 16-bit 48 kHz but can still output at up to 8 channels.[148] No graphic cards were released in 2008 that implemented the Protected Audio Path.[148]

The Asus Xonar HDAV1.3 became the first HDMI sound card that implemented the Protected Audio Path and could both bitstream and decode lossless audio (Dolby TrueHD and DTS-HD MA), although bitstreaming is only available if using the ArcSoft TotalMedia Theatre software.[161][162] It has an HDMI 1.3 input/output, and Asus says that it can work with most video cards on the market.[161][162][163]

In September 2009, AMD announced the ATI Radeon HD 5000 series video cards, which have HDMI 1.3 output (deep color, xvYCC wide gamut capability and high bit rate audio), 8-channel LPCM over HDMI, and an integrated HD audio controller with a Protected Audio Path that allows bitstream output over HDMI for AAC, Dolby AC-3, Dolby TrueHD and DTS-HD Master Audio formats.[164][165][166] The ATI Radeon HD 5870 released in September 2009 is the first video card that allows bitstream output over HDMI for Dolby TrueHD and DTS-HD Master Audio.[166] The AMD Radeon HD 6000 Series implements HDMI 1.4a. The AMD Radeon HD 7000 Series implements HDMI 1.4b.[167]

In December 2010, it was announced that several computer vendors and display makers including Intel, AMD, Dell, Lenovo, Samsung, and LG would stop using LVDS (actually, FPD-Link) from 2013 and legacy DVI and VGA connectors from 2015, replacing them with DisplayPort and HDMI.[168][169]

On August 27, 2012, Asus announced a new 27 in (69 cm) monitor that produces its native resolution of 2560×1440 via HDMI 1.4.[170][171]

On September 18, 2014, Nvidia launched GeForce GTX 980 and GTX 970 (with GM204 chip) with HDMI 2.0 support. On January 22, 2015, GeForce GTX 960 (with GM206 chip) launched with HDMI 2.0 support. On March 17, 2015, GeForce GTX TITAN X (GM200) launched with HDMI 2.0 support. On June 1, 2015, GeForce GTX 980 Ti (with GM200 chip) launched with HDMI 2.0 support. On August 20, 2015, GeForce GTX 950 (with GM206 chip) launched with HDMI 2.0 support.

On May 6, 2016, Nvidia launched the GeForce GTX 1080 (GP104 GPU) with HDMI 2.0b support.[172]

On September 1, 2020, Nvidia launched the GeForce RTX 30 series, the world's first discrete graphics cards with support for the full 48 Gbit/s bandwidth with Display Stream Compression 1.2 of HDMI 2.1.[173][174][175]

Beginning with the seventh generation of video game consoles, most consoles support HDMI. Video game consoles that support HDMI include the Xbox 360 (1.2a), Xbox One (1.4b), Xbox One S (2.0a), Xbox One X (2.0b), PlayStation 3 (1.3a), PlayStation 4 (1.4b), PlayStation 4 Pro (2.0a), Wii U (1.4a), Nintendo Switch (1.4b), Xbox Series X and Series S (2.1), and PlayStation 5 (2.1).

An HDMI port on the side of a laptop computer

Some tablet computers, such as the Microsoft Surface, Motorola Xoom, BlackBerry PlayBook, Vizio Vtab1008 and Acer Iconia Tab A500, implement HDMI using Micro-HDMI (Type D) ports. Others, such as the ASUS Eee Pad Transformer implement the standard using mini-HDMI (type C) ports. All iPad models have a special A/V adapter that converts Apple's data line to a standard HDMI (Type A) port. Samsung has a similar proprietary thirty-pin port for their Galaxy Tab 10.1 that can adapt to HDMI as well as USB drives. The Dell Streak 5 smartphone/tablet hybrid is capable of outputting over HDMI. While the Streak uses a PDMI port, a separate cradle adds HDMI compatibility. Most Chinese-made tablets running Android OS provide HDMI output using a mini-HDMI (type C) port. Most new laptops and desktops now have built in HDMI as well.

Many recent mobile phones can produce an output of HDMI video via either a micro-HDMI connector or MHL output.[176][177][178][179][180][181][182] Some older phones may use SlimPort to achieve a similar result.

HDMI can only be used with older analog-only devices (using connections such as SCART, VGA, RCA, etc.) by means of a digital-to-analog converter or AV receiver, as the interface does not carry any analog signals (unlike DVI, where devices with DVI-I ports accept or provide either digital or analog signals). Cables are available that contain the necessary electronics, but it is important to distinguish these active converter cables from passive HDMI to VGA cables (which are typically cheaper as they don't include any electronics). The passive cables are only useful if you have a device that is generating or expecting HDMI signals on a VGA connector, or VGA signals on an HDMI connector; this is a non-standard feature, not implemented by most devices.