Leclanché cell

In 1866, Georges Leclanché invented a battery that consisted of a zinc anode and a manganese dioxide cathode wrapped in a porous material, dipped in a jar of ammonium chloride solution. The manganese dioxide cathode had a little carbon mixed into it as well, which improved conductivity and absorption.[6] It provided a voltage of 1.4 volts.[7] This cell achieved very quick success in telegraphy, signalling and electric bell work.

The dry cell form was used to power early telephones—usually from an adjacent wooden box affixed to the wall—before telephones could draw power from the telephone line itself. The Leclanché cell could not provide a sustained current for very long. In lengthy conversations, the battery would run down, rendering the conversation inaudible.[8] This is because certain chemical reactions in the cell increase the internal resistance and, thus, lower the voltage. These reactions reverse themselves when the battery is left idle, so it is good only for intermittent use.[9]

The original form of the cell used a porous pot. This gave it a relatively high internal resistance and various modifications were made to reduce it. These included the "Agglomerate block cell" and the "Sack cell". Leclanché first, and Carl Gassner later, strived both to transform the original wet cell into a more portable and more efficient dry cell.

Porous pot cell

In Leclanché's original cell the depolarizer (in fact, the oxidizing agent in the cell), which consists of crushed manganese dioxide, is packed into a pot, and a carbon rod is inserted to act as the cathode (reduction reaction). The anode (oxidation reaction), which is a zinc rod, is then immersed along with the pot in a solution of ammonium chloride. The liquid solution acts as the electrolyte, permeating through the porous pot to make contact with the cathode.

Agglomerate block cell

In 1871 Leclanché dispensed with the porous pot and replaced it with a pair of "agglomerate blocks", attached to the carbon plate by rubber bands. These blocks were made by mixing the manganese dioxide with binding agents and pressing the mixture into moulds.

Sack cell

In this cell the porous pot is replaced by a wrapping of canvas or sacking. In addition, the zinc rod is replaced by a zinc cylinder to give a larger surface area. It has a lower internal resistance than either of the above (porous and agglomerate).

Starch addition

In 1876, Georges Leclanché added starch to the ammonium chloride electrolyte in an effort to better jellify it.

Improved dry cell

In 1888, a German physician, Carl Gassner improved the jellification process and produced a more portable dry cell by mixing plaster and hydrophilic chemicals with the ammonium chloride electrolyte..

The redox reaction in a Leclanché cell involves the two following half-reactions:

– anode (oxidation of Zn): Zn → Zn²⁺ + 2e⁻

– cathode (reduction of Mn(IV)): 2 MnO₂ + 2NH₄⁺ + 2e⁻ → 2 MnO(OH) + 2 NH₃

The chemical process which produces electricity in a Leclanché cell begins when zinc atoms on the surface of the anode oxidize, i.e. they give up both their valence electrons to become positively charged Zn²⁺ ions. As the Zn²⁺ ions move away from the anode, leaving their electrons on its surface, the anode becomes more negatively charged than the cathode. When the cell is connected in an external electrical circuit, the excess electrons on the zinc anode flow through the circuit to the carbon rod, the movement of electrons forming an electric current.

As the current travels around the circuit, when the electrons enter the cathode (carbon rod), they combine with manganese dioxide (MnO₂) and water (H₂O), which react with each other to produce manganese oxide (Mn₂O₃) and negatively charged hydroxide ions. This is accompanied by a secondary acid-base reaction in which the hydroxide ions (OH^–) accept a proton (H⁺) from the ammonium ions present in the ammonium chloride electrolyte to produce molecules of ammonia and water.[10]

Zn(s) + 2 MnO₂(s) + 2 NH₄Cl(aq) → ZnCl₂(aq) + Mn₂O₃(s) + 2 NH₃(aq) + H₂O(l),

or if one also considers the hydration of the Mn₂O₃(s) sesquioxide into Mn(III) oxy-hydroxide:

Zn(s) + 2 MnO₂(s) + 2 NH₄Cl(aq) → ZnCl₂(aq) + 2 MnO(OH)(s) + 2 NH₃(aq)

Alternately, the reduction reaction of Mn(IV) can proceed further, forming Mn(II) hydroxide.

Zn(s) + MnO₂(s) + 2 NH₄Cl(aq) → ZnCl₂(aq) + Mn(OH)₂(s) + 2 NH₃(aq)

The electromotive force (e.m.f.) produced by a Leclanche cell is 1.4 volts, with a resistance of several ohms where a porous pot is used.[7] It saw extensive usage in telegraphy, signaling, electric bells and similar applications where intermittent current was required and it was desirable that a battery should require little maintenance.

The Leclanché battery wet cell was the forerunner of the modern zinc-carbon battery (a dry cell). The addition of zinc chloride to the electrolyte paste raises the e.m.f. to 1.5 volts. Later developments dispensed with the ammonium chloride completely, giving a cell that can endure more sustained discharge without its internal resistance rising as quickly (the zinc chloride cell).

• List of battery types
• History of the battery
• Alkaline battery, a similar cell in which the NH₄Cl electrolyte has been replaced by KOH. This improved type of battery with a much higher charge density (5 ×) was commercialised much later (1960/70).

• Practical Electricity by W. E. Ayrton and T. Mather, published by Cassell and Company, London, 1911, pp 188–193