Intel 80386

The Intel 80386, also known as i386 or just 386, is a 32-bit microprocessor introduced in 1985.[2] The first versions had 275,000 transistors[3] and were the CPU of many workstations and high-end personal computers of the time. As the original implementation of the 32-bit extension of the 80286 architecture,[4] the 80386 instruction set, programming model, and binary encodings are still the common denominator for all 32-bit x86 processors, which is termed the i386-architecture, x86, or IA-32, depending on context.

"386 DX" redirects here. For the Russian artist and musician, see Alexei Shulgin.
"i386" redirects here. For the instruction set first introduced in the 80386, see IA-32.

Intel 80386
An Intel 80386DX 16 MHz processor with a gray ceramic heat spreader.
General information
LaunchedOctober 1985
DiscontinuedSeptember 28, 2007[1]
Common manufacturer(s)
  • Intel
  • AMD
  • IBM
Performance
Max. CPU clock rate12 MHz to 40 MHz
Data width32 bits (386SX: 16 bit)
Address width32 bits (386SX: 24 bits)
Architecture and classification
Min. feature size1.5µm to 1µm
Instruction setx86-32
Physical specifications
Transistors
  • 275,000
Co-processorIntel 80387
Package(s)
  • 132-pin PGA, 132-pin PQFP; SX variant: 88-pin PGA, 100-pin BQFP with 0.635mm pitch
Socket(s)
History
PredecessorIntel 80286
SuccessorIntel 80486
Intel A80386DX-20 CPU die image

The 32-bit 80386 can correctly execute most code intended for the earlier 16-bit processors such as 8086 and 80286 that were ubiquitous in early PCs. (Following the same tradition, modern 64-bit x86 processors are able to run most programs written for older x86 CPUs, all the way back to the original 16-bit 8086 of 1978.) Over the years, successively newer implementations of the same architecture have become several hundreds of times faster than the original 80386 (and thousands of times faster than the 8086).[5] A 33 MHz 80386 was reportedly measured to operate at about 11.4 MIPS.[6]

The 80386 was introduced in October 1985, while manufacturing of the chips in significant quantities commenced in June 1986.[7][8] Mainboards for 80386-based computer systems were cumbersome and expensive at first, but manufacturing was justified upon the 80386's mainstream adoption. The first personal computer to make use of the 80386 was designed and manufactured by Compaq[9] and marked the first time a fundamental component in the IBM PC compatible de facto standard was updated by a company other than IBM.

In May 2006, Intel announced that 80386 production would stop at the end of September 2007.[10] Although it had long been obsolete as a personal computer CPU, Intel and others had continued making the chip for embedded systems. Such systems using an 80386 or one of many derivatives are common in aerospace technology and electronic musical instruments, among others. Some mobile phones also used (later fully static CMOS variants of) the 80386 processor, such as BlackBerry 950[11] and Nokia 9000 Communicator. Linux continued to support 80386 processors until December 11, 2012; when the kernel cut 386-specific instructions in version 3.8.[12]

Architecture
Block diagram of the i386 microarchitecture
Intel 80386 registers
31 ... 15 ... 07 ... 00 (bit position)
Main registers (8/16/32 bits)
EAX AX AL Accumulator register
EBX BX BL Base register
ECX CX CL Count register
EDX DX DL Data register
Index registers (16/32 bits)
ESI SI Source Index
EDI DI Destination Index
EBP BP Base Pointer
ESP SP Stack Pointer
Program counter (16/32 bits)
EIP IP Instruction Pointer
Segment selectors (16 bits)
  CS Code Segment
  DS Data Segment
  ES Extra Segment
  FS F Segment
  GS G Segment
  SS Stack Segment
Status register
  17 16 15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00 (bit position)
  V R 0 N IOPL O D I T S Z 0 A 0 P 1 C EFlags

The processor was a significant evolution in the x86 architecture, and extended a long line of processors that stretched back to the Intel 8008. The predecessor of the 80386 was the Intel 80286, a 16-bit processor with a segment-based memory management and protection system. The 80386 added a three-stage instruction pipeline, extended the architecture from 16-bits to 32-bits, and added an on-chip memory management unit. This paging translation unit made it much easier to implement operating systems that used virtual memory. It also offered support for register debugging.

The 80386 featured three operating modes: real mode, protected mode and virtual mode. The protected mode, which debuted in the 286, was extended to allow the 386 to address up to 4 GB of memory. The all new virtual 8086 mode (or VM86) made it possible to run one or more real mode programs in a protected environment, although some programs were not compatible.

The ability for a 386 to be set up to act like it had a flat memory model in protected mode despite the fact that it uses a segmented memory model in all modes was arguably the most important feature change for the x86 processor family until AMD released x86-64 in 2003.

Several new instructions have been added to 386: BSF, BSR, BT, BTS, BTR, BTC, CDQ, CWDE, LFS, LGS, LSS, MOVSX, MOVZX, SETcc, SHLD, SHRD.

Two new segment registers have been added (FS and GS) for general-purpose programs, single Machine Status Word of 286 grew into eight control registers CR0–CR7. Debug registers DR0–DR7 were added for hardware breakpoints. New forms of MOV instruction are used to access them.

Chief architect in the development of the 80386 was John H. Crawford.[13] He was responsible for extending the 80286 architecture and instruction set to 32-bit, and then led the microprogram development for the 80386 chip.

The 80486 and P5 Pentium line of processors were descendants of the 80386 design.

Datatypes of 80386

The following data types are directly supported and thus implemented by one or more 80386 machine instructions; these data types are briefly described here.[14]:

  • Bit (boolean value), bit field (group of up to 32 bits) and bit string (up to 4 Gbit in length).
  • 8-bit integer (byte), either signed (range −128..127) or unsigned (range 0..255).
  • 16-bit integer, either signed (range −32,768..32,767) or unsigned (range 0..65,535).
  • 32-bit integer, either signed (range −231..231−1) or unsigned (range 0..232−1).
  • 64-bit integer, either signed (range −263..263−1) or unsigned (range 0..264−1).
  • Offset, a 16- or 32-bit displacement referring to a memory location (using any addressing mode).
  • Pointer, a 16-bit selector together with a 16- or 32-bit offset.
  • Character (8-bit character code).
  • String, a sequence of 8-, 16- or 32-bit words (up to 4 Gbit in length).[15]
  • BCD, decimal digits (0..9) represented by unpacked bytes.
  • Packed BCD, two BCD digits in one byte (range 0..99).

Example code

The following 80386 assembly source code is for a subroutine named _strtolower that copies a null-terminated ASCIIZ character string from one location to another, converting all alphabetic characters to lower case. The string is copied one byte (8-bit character) at a time.

                         
                         
                         
                         
                         
                         
                         
                         
                         
00000000                     
00000000  55
00000001  89 E5
00000003  8B 75 0C
00000006  8B 7D 08
00000009  8A 06
0000000B  46
0000000C  3C 41
0000000E  7C 06
00000010  3C 5A
00000012  7F 02
00000014  04 20
00000016  88 07
00000018  47
00000019  3C 00
0000001B  75 EC
0000001D  5D
0000001E  C3          
0000001F          

; _strtolower:
; Copy a null-terminated ASCII string, converting
; all alphabetic characters to lower case.
;
; Entry stack parameters
;      [ESP+8] = src, Address of source string
;      [ESP+4] = dst, Address of target string
;      [ESP+0] = Return address
;
_strtolower proc
            push    ebp             ;Set up the call frame
            mov     ebp,esp
            mov     esi,[ebp+12]    ;Set ESI = src
            mov     edi,[ebp+8]     ;Set EDI = dst
loop        mov     al,[esi]        ;Load AL from [src]
            inc     esi             ;Increment src
            cmp     al,'A'          ;If AL < 'A',
            jl      copy            ; Skip conversion
            cmp     al,'Z'          ;If AL > 'Z',
            jg      copy            ; Skip conversion
            add     al,'a'-'A'      ;Convert AL to lowercase
copy        mov     [edi],al        ;Store AL to [dst]
            inc     edi             ;Increment dst
            cmp     al,0            ;If AL <> 0,
            jne     loop            ; Repeat the loop
done        pop     ebp             ;Restore the prev call frame
            ret                     ;Return to caller
            end     proc

The example code uses the EBP (base pointer) register to establish a call frame, an area on the stack that contains all of the parameters and local variables for the execution of the subroutine. This kind of calling convention supports reentrant and recursive code and has been used by Algol-like languages since the late 1950s. A flat memory model is assumed, specifically, that the DS and ES segments address the same region of memory.

Chip variants

80386SX
A surface-mount version of Intel 80386SX processor in a Compaq Deskpro computer. It is non-upgradable unless hot air circuit board rework is performed
Die of Intel 80386SX
80386SL from 1990

In 1988, Intel introduced the 80386SX, most often referred to as the 386SX, a cut-down version of the 80386 with a 16-bit data bus mainly intended for lower-cost PCs aimed at the home, educational, and small-business markets, while the 386DX remained the high-end variant used in workstations, servers, and other demanding tasks. The CPU remained fully 32-bit internally, but the 16-bit bus was intended to simplify circuit-board layout and reduce total cost.[16] The 16-bit bus simplified designs but hampered performance. Only 24 pins were connected to the address bus, therefore limiting addressing to 16 MB,[17] but this was not a critical constraint at the time. Performance differences were due not only to differing data-bus widths, but also due to performance-enhancing cache memories often employed on boards using the original chip.

The original 80386 was subsequently renamed 80386DX to avoid confusion. However, Intel subsequently used the "DX" suffix to refer to the floating-point capability of the 80486DX. The 80387SX was an 80387 part that was compatible with the 386SX (i.e. with a 16-bit databus). The 386SX was packaged in a surface-mount QFP and sometimes offered in a socket to allow for an upgrade.

i386SL

The i386SL was introduced as a power-efficient version for laptop computers. The processor offered several power-management options (e.g. SMM), as well as different "sleep" modes to conserve battery power. It also contained support for an external cache of 16 to 64 kB. The extra functions and circuit implementation techniques caused this variant to have over 3 times as many transistors as the i386DX. The i386SL was first available at 20 MHz clock speed,[18] with the 25 MHz model later added.[19]

Business importance

The first company to design and manufacture a PC based on the Intel 80386 was Compaq. By extending the 16/24-bit IBM PC/AT standard into a natively 32-bit computing environment, Compaq became the first third party to implement a major technical hardware advance on the PC platform. IBM was offered use of the 80386, but had manufacturing rights for the earlier 80286. IBM therefore chose to rely on that processor for a couple more years. The early success of the Compaq 386 PC played an important role in legitimizing the PC "clone" industry and in de-emphasizing IBM's role within it.

Prior to the 386, the difficulty of manufacturing microchips and the uncertainty of reliable supply made it desirable that any mass-market semiconductor be multi-sourced, that is, made by two or more manufacturers, the second and subsequent companies manufacturing under license from the originating company. The 386 was for a time (4.7 years) only available from Intel, since Andy Grove, Intel's CEO at the time, made the decision not to encourage other manufacturers to produce the processor as second sources. This decision was ultimately crucial to Intel's success in the market. The 386 was the first significant microprocessor to be single-sourced. Single-sourcing the 386 allowed Intel greater control over its development and substantially greater profits in later years.

AMD introduced its compatible Am386 processor in March 1991 after overcoming legal obstacles, thus ending Intel's 4.7-year monopoly on 386-compatible processors. From 1991 IBM also manufactured 386 chips under license for use only in IBM PCs and boards.

Compatibles
Intel i386 packaged by IBM
  • The AMD Am386SX and Am386DX were almost exact clones of the 80386SX and 80386DX. Legal disputes caused production delays for several years, but AMD's 40 MHz part eventually became very popular with computer enthusiasts as a low-cost and low-power alternative to the 25 MHz 486SX. The power draw was further reduced in the "notebook models" (Am386 DXL/SXL/DXLV/SXLV), which could operate with 3.3 V and were implemented in fully static CMOS circuitry.
  • Chips and Technologies Super386 38600SX and 38600DX were developed using reverse engineering. They sold poorly, due to some technical errors and incompatibilities, as well as their late appearance on the market. They were therefore short-lived products.
  • Cyrix Cx486SLC/Cx486DLC could be (simplistically) described as a kind of 386/486 hybrid chip that included a small amount of on-chip cache. It was popular among computer enthusiasts but did poorly with OEMs. The Cyrix Cx486SLC and Cyrix Cx486DLC processors were pin-compatible with 80386SX and 80386DX respectively. These processors were also manufactured and sold by Texas Instruments.
  • IBM 386SLC and 486SLC/DLC were variants of Intel's design which contained a large amount of on-chip cache (8 kB, and later 16 kB). The agreement with Intel limited their use to IBM's own line of computers and upgrade boards only, so they were not available on the open market.

Early problems

Intel originally intended for the 80386 to debut at 16 MHz. However, due to poor yields, it was instead introduced at 12.5 MHz.

Early in production, Intel discovered a marginal circuit that could cause a system to return incorrect results from 32-bit multiply operations. Not all of the processors already manufactured were affected, so Intel tested its inventory. Processors that were found to be bug-free were marked with a double sigma (ΣΣ), and affected processors were marked "16 BIT S/W ONLY". These latter processors were sold as good parts, since at the time 32-bit capability was not relevant for most users. Such chips are now extremely rare and became collectible.

The i387 math coprocessor was not ready in time for the introduction of the 80386, and so many of the early 80386 motherboards instead provided a socket and hardware logic to make use of an 80287. In this configuration the FPU operated asynchronously to the CPU, usually with a clock rate of 10 MHz. The original Compaq Deskpro 386 is an example of such design. However, this was an annoyance to those who depended on floating-point performance, as the performance advantages of the 80387 over the 80287 were significant.

  • A very early 80386 at 12 MHz (A80386-12), before the 32-bit multiply bug was found
  • An A80386-16 marked "16 BIT S/W ONLY" with the multiply bug
  • A bug-free A80386-16 marked "ΣΣ"

Pin-compatible upgrades
Typical 386 upgrade CPUs from Cyrix and Texas Instruments

Intel later offered a modified version of its 80486DX in 80386 packaging, branded as the Intel RapidCAD. This provided an upgrade path for users with 80386-compatible hardware. The upgrade was a pair of chips that replaced both the 80386 and 80387. Since the 80486DX design contained an FPU, the chip that replaced the 80386 contained the floating-point functionality, and the chip that replaced the 80387 served very little purpose. However, the latter chip was necessary in order to provide the FERR signal to the mainboard and appear to function as a normal floating-point unit.

Third parties offered a wide range of upgrades, for both SX and DX systems. The most popular ones were based on the Cyrix 486DLC/SLC core, which typically offered a substantial speed improvement due to its more efficient instruction pipeline and internal L1 SRAM cache. The cache was usually 1 kB, or sometimes 8 kB in the TI variant. Some of these upgrade chips (such as the 486DRx2/SRx2) were marketed by Cyrix themselves, but they were more commonly found in kits offered by upgrade specialists such as Kingston, Evergreen and Improve-It Technologies. Some of the fastest CPU upgrade modules featured the IBM SLC/DLC family (notable for its 16 kB L1 cache), or even the Intel 486 itself. Many 386 upgrade kits were advertised as being simple drop-in replacements, but often required complicated software to control the cache or clock doubling. Part of the problem was that on most 386 motherboards, the A20 line was controlled entirely by the motherboard with the CPU being unaware, which caused problems on CPUs with internal caches.

Overall, it was very difficult to configure upgrades to produce the results advertised on the packaging, and upgrades were often not very stable or not fully compatible.

Models and variants

80386DX
Intel 80386DX, 25 MHz

Original version, released in October 1985.

  • Capable of working with 16- or 32-bit external busses
  • Cache: depends on mainboard
  • Package: PGA-132 or PQFP-132
  • Process: First types CHMOS III, 1.5 µm, later CHMOS IV, 1 µm
  • Die size: 104 mm² (ca. 10 mm × 10 mm) in CHMOS III and 39 mm² (6 mm × 6.5 mm) in CHMOS IV.
  • Transistor count: 275,000[3]
  • Specified max clock: 12 MHz (early models), later 16, 20, 25 and 33 MHz
80386SX 16 MHz

RapidCAD
Main article: RapidCAD

A specially packaged Intel 486DX and a dummy floating point unit (FPU) designed as pin-compatible replacements for an Intel 80386 processor and 80387 FPU.

80376
Main article: Intel 80376

This was an embedded version of the 80386SX which did not support real mode and paging in the MMU.

i386EX, i386EXTB and i386EXTC
Main article: Intel 80386EX
Intel i386EXTC, 25 MHz

System and power management and built in peripheral and support functions: Two 82C59A interrupt controllers; Timer, Counter (3 channels); Asynchronous SIO (2 channels); Synchronous SIO (1 channel); Watchdog timer (Hardware/Software); PIO. Usable with 80387SX or i387SL FPUs.

  • Data/address bus: 16 / 26 bits
  • Package: PQFP-132, SQFP-144 and PGA-168
  • Process: CHMOS V, 0.8 µm
  • Specified max clock:
    • i386EX: 16 MHz @2.7~3.3 volt or 20 MHz @3.0~3.6 volt or 25 MHz @4.5~5.5 volt
    • i386EXTB: 20 MHz @2.7~3.6 volt or 25 MHz @3.0~3.6 volt
    • i386EXTC: 25 MHz @4.5~5.5 volt or 33 MHz @4.5~5.5 volt

i386CXSA and i386SXSA (or i386SXTA)
Intel i386CXSA, 25 MHz

Transparent power management mode, integrated MMU and TTL compatible inputs (only 386SXSA). Usable with i387SX or i387SL FPUs.

  • Data/address bus: 16 / 26 bits (24 bits for i386SXSA)
  • Package: BQFP-100
  • Voltage: 4.5~5.5 volt (25 and 33 MHz); 4.75~5.25 volt (40 MHz)
  • Process: CHMOS V, 0.8 µm
  • Specified max clock: 25, 33, 40 MHz

i386CXSB

Transparent power management mode and integrated MMU. Usable with i387SX or i387SL FPUs.

  • Data/address bus: 16 / 26 bits
  • Package: BQFP-100
  • Voltage: 3.0 volt (16 MHz) or 3.3 volt (25 MHz)
  • Process: CHMOS V, 0.8 µm
  • Specified max clock: 16, 25 MHz

Obsolescence

Windows 95 was the only entry in the Windows 9x series to officially support the 386, requiring at least a 386DX, though a 486 or better was recommended;[20] Windows 98 requires a 486DX or higher.[21] In the Windows NT family, Windows NT 3.51 was the last version with 386 support.[22][23]

Debian GNU/Linux removed 386 support with the release of 3.1 (Sarge) in 2005.[24] Citing the maintenance burden around SMP primitives, the Linux kernel developers cut support from the development codebase in December 2012, later released as kernel version 3.8.[12]

Among the BSDs, FreeBSD's 5.x releases were the last to support the 386; support for the 386SX was cut with release 5.2,[25] while the remaining 386 support was removed with the 6.0 release in 2005.[26] OpenBSD removed 386 support with version 4.2 (2007),[27] DragonFly BSD with release 1.12 (2008),[28] and NetBSD with the 5.0 release (2009).[29]

See also
  • List of Intel microprocessors

Notes and references
  1. Product Change Notification.
  2. More precise: The 80386 architecture was presented in detail in 1984. Samples were produced in 1985 (possibly late 1984) with mass production and delivery of a final version starting in June 1986.
  3. mit.edu—The Future of FPGAs (Cornell) October 11, 2012
  4. Which itself was an extension of the 8086-architecture with advanced memory management functions and significantly better performance.
  5. Not counting the advances in the performance of corresponding x87 implementations. These are measured in tens of thousands of times, compared to the original 8087, or hundreds of thousands of times compared to software implementations of floating point on the 8086.
  6. "Intel Architecure Programming and Information". intel80386.com. Retrieved March 15, 2018.
  7. Forbes, Jim (January 27, 1986). "Development of 386 Accelerating". InfoWorld. Vol. 8 no. 4. InfoWorld Media Group. p. 5. ISSN 0199-6649. Introduced October 1985, production chip in June 1986.
  8. Ranney, Elizabeth (September 1, 1986). "ALR Hopes to Beat Completion With Fall Release of 386 Line". InfoWorld. Vol. 8 no. 35. InfoWorld Media Group. p. 5. ISSN 0199-6649. The first 80386 computers were released around October 1986.
  9. "CRN". June 27, 2009. Archived from the original on June 27, 2009. Retrieved March 15, 2018 – via archive.org.
  10. "Intel cashes in ancient chips". Archived from the original on August 22, 2011. Retrieved May 18, 2006.
  11. "RIM BlackBerry 950 Review - The Gadgeteer". the-gadgeteer.com. February 26, 2001. Retrieved March 15, 2018.
  12. Larabel, Michael (December 12, 2012). "Linux Kernel Drops Support For Old Intel 386 CPUs". Phoronix. Retrieved October 14, 2019.
  13. "Intel Fellow—John H. Crawford". Intel.com. August 16, 2010. Retrieved September 17, 2010.
  14. A. K. Ray, K. M. Bhurchandi, “Advanced microprocessors and peripherals”.
  15. El-ayat, K. A.; Agarwal, R. K. (December 1985). "The Intel 80386 - Architecture And Implementation". IEEE Micro. 5 (6): 4–22. doi:10.1109/mm.1985.304507. ISSN 0272-1732.
  16. This was a similar approach to that used by Intel with the 8088, a derivative of the Intel 8086, that was used in the original IBM PC.
  17. The 16 MB limit was similar to that of the 68000, a comparable processor.
  18. "Chronology of Microprocessors (1990-1992)". Islandnet.com. Retrieved September 17, 2010.
  19. Mueller, Scott. "Microprocessor Types and Specifications > P3 (386) Third-Generation Processors". InformIT. Retrieved September 17, 2010.
  20. "Windows 95 Installation Requirements". Microsoft Support. Microsoft. December 17, 2000. Archived from the original on October 19, 2004. Retrieved September 1, 2020.
  21. "Windows 98 Product Guide: System Requirements". microsoft.com. Microsoft. December 4, 1998. Archived from the original on April 20, 1999. Retrieved August 31, 2020.
  22. "Windows NT 3.5x Setup Troubleshooting Guide". Microsoft Support. Microsoft. Archived from the original on February 23, 2007. Retrieved August 31, 2020.
  23. "Windows NT Workstation 4.0 - Requirements". microsoft.com. Microsoft. January 29, 1999. Archived from the original on February 2, 1999. Retrieved August 31, 2020.
  24. "Release Notes for Debian GNU/Linux 3.1 (`sarge'), Intel x86 - Upgrades from previous releases". debian.org. The Debian Project. June 2005. Retrieved September 1, 2020.
  25. "FreeBSD/i386 5.2-RELEASE Hardware Notes". freebsd.org. The FreeBSD Project. January 2004. Retrieved August 31, 2020.
  26. "FreeBSD/i386 6.0-RELEASE Release Notes". freebsd.org. The FreeBSD Project. November 2005. Retrieved August 31, 2020.
  27. "OpenBSD 4.2 Changelog". openbsd.org. The OpenBSD project. November 2007. Retrieved August 31, 2020.
  28. "DragonFly 1.12.0 Release Notes". dragonflybsd.org. The DragonFly Project. February 26, 2008. Retrieved August 31, 2020.
  29. "Announcing NetBSD 5.0". netbsd.org. The NetBSD Foundation. April 2009. Retrieved August 31, 2020.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.