Robotics

The InSight lander with solar panels deployed in a cleanroom

At present, mostly (lead–acid) batteries are used as a power source. Many different types of batteries can be used as a power source for robots. They range from lead–acid batteries, which are safe and have relatively long shelf lives but are rather heavy compared to silver–cadmium batteries that are much smaller in volume and are currently much more expensive. Designing a battery-powered robot needs to take into account factors such as safety, cycle lifetime and weight. Generators, often some type of internal combustion engine, can also be used. However, such designs are often mechanically complex and need a fuel, require heat dissipation and are relatively heavy. A tether connecting the robot to a power supply would remove the power supply from the robot entirely. This has the advantage of saving weight and space by moving all power generation and storage components elsewhere. However, this design does come with the drawback of constantly having a cable connected to the robot, which can be difficult to manage.[36] Potential power sources could be:

• pneumatic (compressed gases)
• Solar power (using the sun's energy and converting it into electrical power)
• hydraulics (liquids)
• flywheel energy storage
• organic garbage (through anaerobic digestion)
• nuclear

A robotic leg powered by air muscles

Actuators are the "muscles" of a robot, the parts which convert stored energy into movement.[37] By far the most popular actuators are electric motors that rotate a wheel or gear, and linear actuators that control industrial robots in factories. There are some recent advances in alternative types of actuators, powered by electricity, chemicals, or compressed air.

The vast majority of robots use electric motors, often brushed and brushless DC motors in portable robots or AC motors in industrial robots and CNC machines. These motors are often preferred in systems with lighter loads, and where the predominant form of motion is rotational.

Various types of linear actuators move in and out instead of by spinning, and often have quicker direction changes, particularly when very large forces are needed such as with industrial robotics. They are typically powered by compressed and oxidized air (pneumatic actuator) or an oil (hydraulic actuator) Linear actuators can also be powered by electricity which usually consists of a motor and a leadscrew. Another common type is a mechanical linear actuator that is turned by hand, such as a rack and pinion on a car.

Series elastic actuation (SEA) relies on the idea of introducing intentional elasticity between the motor actuator and the load for robust force control. Due to the resultant lower reflected inertia, series elastic actuation improves safety when a robot interacts with the environment (e.g., humans or workpiece) or during collisions.[38] Furthermore, it also provides energy efficiency and shock absorption (mechanical filtering) while reducing excessive wear on the transmission and other mechanical components. This approach has successfully been employed in various robots, particularly advanced manufacturing robots [39] and walking humanoid robots.[40][41]

The controller design of a series elastic actuator is most often performed within the passivity framework as it ensures the safety of interaction with unstructured environments.[42] Despite its remarkable stability robustness, this framework suffers from the stringent limitations imposed on the controller which may trade-off performance.The reader is referred to the following survey which summarizes the common controller architectures for SEA along with the corresponding sufficient passivity conditions.[43] One recent study has derived the necessary and sufficient passivity conditions for one of the most common impedance control architectures, namely velocity-sourced SEA.[44] This work is of particular importance as it drives the non-conservative passivity bounds in an SEA scheme for the first time which allows a larger selection of control gains.

Pneumatic artificial muscles, also known as air muscles, are special tubes that expand(typically up to 40%) when air is forced inside them. They are used in some robot applications.[45][46][47]

Muscle wire, also known as shape memory alloy, Nitinol® or Flexinol® wire, is a material which contracts (under 5%) when electricity is applied. They have been used for some small robot applications.[48][49]

EAPs or EPAMs are a plastic material that can contract substantially (up to 380% activation strain) from electricity, and have been used in facial muscles and arms of humanoid robots,[50] and to enable new robots to float,[51] fly, swim or walk.[52]

Recent alternatives to DC motors are piezo motors or ultrasonic motors. These work on a fundamentally different principle, whereby tiny piezoceramic elements, vibrating many thousands of times per second, cause linear or rotary motion. There are different mechanisms of operation; one type uses the vibration of the piezo elements to step the motor in a circle or a straight line.[53] Another type uses the piezo elements to cause a nut to vibrate or to drive a screw. The advantages of these motors are nanometer resolution, speed, and available force for their size.[54] These motors are already available commercially, and being used on some robots.[55][56]

Elastic nanotubes are a promising artificial muscle technology in early-stage experimental development. The absence of defects in carbon nanotubes enables these filaments to deform elastically by several percent, with energy storage levels of perhaps 10 J/cm³ for metal nanotubes. Human biceps could be replaced with an 8 mm diameter wire of this material. Such compact "muscle" might allow future robots to outrun and outjump humans.[57]

Sensors allow robots to receive information about a certain measurement of the environment, or internal components. This is essential for robots to perform their tasks, and act upon any changes in the environment to calculate the appropriate response. They are used for various forms of measurements, to give the robots warnings about safety or malfunctions, and to provide real-time information of the task it is performing.

Current robotic and prosthetic hands receive far less tactile information than the human hand. Recent research has developed a tactile sensor array that mimics the mechanical properties and touch receptors of human fingertips.[58][59] The sensor array is constructed as a rigid core surrounded by conductive fluid contained by an elastomeric skin. Electrodes are mounted on the surface of the rigid core and are connected to an impedance-measuring device within the core. When the artificial skin touches an object the fluid path around the electrodes is deformed, producing impedance changes that map the forces received from the object. The researchers expect that an important function of such artificial fingertips will be adjusting robotic grip on held objects.

Scientists from several European countries and Israel developed a prosthetic hand in 2009, called SmartHand, which functions like a real one—allowing patients to write with it, type on a keyboard, play piano and perform other fine movements. The prosthesis has sensors which enable the patient to sense real feeling in its fingertips.[60]

Computer vision is the science and technology of machines that see. As a scientific discipline, computer vision is concerned with the theory behind artificial systems that extract information from images. The image data can take many forms, such as video sequences and views from cameras.

In most practical computer vision applications, the computers are pre-programmed to solve a particular task, but methods based on learning are now becoming increasingly common.

Computer vision systems rely on image sensors which detect electromagnetic radiation which is typically in the form of either visible light or infra-red light. The sensors are designed using solid-state physics. The process by which light propagates and reflects off surfaces is explained using optics. Sophisticated image sensors even require quantum mechanics to provide a complete understanding of the image formation process. Robots can also be equipped with multiple vision sensors to be better able to compute the sense of depth in the environment. Like human eyes, robots' "eyes" must also be able to focus on a particular area of interest, and also adjust to variations in light intensities.

There is a subfield within computer vision where artificial systems are designed to mimic the processing and behavior of biological system, at different levels of complexity. Also, some of the learning-based methods developed within computer vision have their background in biology.

Other common forms of sensing in robotics use lidar, radar, and sonar.[61] Lidar measures distance to a target by illuminating the target with laser light and measuring the reflected light with a sensor. Radar uses radio waves to determine the range, angle, or velocity of objects. Sonar uses sound propagation to navigate, communicate with or detect objects on or under the surface of the water.

KUKA industrial robot operating in a foundry

Puma, one of the first industrial robots

Baxter, a modern and versatile industrial robot developed by Rodney Brooks

A definition of robotic manipulation has been provided by Matt Mason as: "manipulation refers to an agent’s control of its environment through selective contact”.[62]

Robots need to manipulate objects; pick up, modify, destroy, or otherwise have an effect. Thus the functional end of a robot arm intended to make the effect (whether a hand, or tool) are often referred to as end effectors,[63] while the "arm" is referred to as a manipulator.[64] Most robot arms have replaceable end-effectors, each allowing them to perform some small range of tasks. Some have a fixed manipulator that cannot be replaced, while a few have one very general purpose manipulator, for example, a humanoid hand.[65]

One of the most common types of end-effectors are "grippers". In its simplest manifestation, it consists of just two fingers that can open and close to pick up and let go of a range of small objects. Fingers can, for example, be made of a chain with a metal wire run through it.[66] Hands that resemble and work more like a human hand include the Shadow Hand and the Robonaut hand.[67] Hands that are of a mid-level complexity include the Delft hand.[68][69] Mechanical grippers can come in various types, including friction and encompassing jaws. Friction jaws use all the force of the gripper to hold the object in place using friction. Encompassing jaws cradle the object in place, using less friction.

Suction end-effectors, powered by vacuum generators, are very simple astrictive[70] devices that can hold very large loads provided the prehension surface is smooth enough to ensure suction.

Pick and place robots for electronic components and for large objects like car windscreens, often use very simple vacuum end-effectors.

Suction is a highly used type of end-effector in industry, in part because the natural compliance of soft suction end-effectors can enable a robot to be more robust in the presence of imperfect robotic perception. As an example: consider the case of a robot vision system estimates the position of a water bottle, but has 1 centimeter of error. While this may cause a rigid mechanical gripper to puncture the water bottle, the soft suction end-effector may just bend slightly and conform to the shape of the water bottle surface.

Some advanced robots are beginning to use fully humanoid hands, like the Shadow Hand, MANUS,[71] and the Schunk hand.[72] These are highly dexterous manipulators, with as many as 20 degrees of freedom and hundreds of tactile sensors.[73]

Segway in the Robot museum in Nagoya

For simplicity, most mobile robots have four wheels or a number of continuous tracks. Some researchers have tried to create more complex wheeled robots with only one or two wheels. These can have certain advantages such as greater efficiency and reduced parts, as well as allowing a robot to navigate in confined places that a four-wheeled robot would not be able to.

Balancing robots generally use a gyroscope to detect how much a robot is falling and then drive the wheels proportionally in the same direction, to counterbalance the fall at hundreds of times per second, based on the dynamics of an inverted pendulum.[74] Many different balancing robots have been designed.[75] While the Segway is not commonly thought of as a robot, it can be thought of as a component of a robot, when used as such Segway refer to them as RMP (Robotic Mobility Platform). An example of this use has been as NASA's Robonaut that has been mounted on a Segway.[76]

A one-wheeled balancing robot is an extension of a two-wheeled balancing robot so that it can move in any 2D direction using a round ball as its only wheel. Several one-wheeled balancing robots have been designed recently, such as Carnegie Mellon University's "Ballbot" that is the approximate height and width of a person, and Tohoku Gakuin University's "BallIP".[77] Because of the long, thin shape and ability to maneuver in tight spaces, they have the potential to function better than other robots in environments with people.[78]

Several attempts have been made in robots that are completely inside a spherical ball, either by spinning a weight inside the ball,[79][80] or by rotating the outer shells of the sphere.[81][82] These have also been referred to as an orb bot[83] or a ball bot.[84][85]

Using six wheels instead of four wheels can give better traction or grip in outdoor terrain such as on rocky dirt or grass.

TALON military robots used by the United States Army

Tank tracks provide even more traction than a six-wheeled robot. Tracked wheels behave as if they were made of hundreds of wheels, therefore are very common for outdoor and military robots, where the robot must drive on very rough terrain. However, they are difficult to use indoors such as on carpets and smooth floors. Examples include NASA's Urban Robot "Urbie".[86]

Walking is a difficult and dynamic problem to solve. Several robots have been made which can walk reliably on two legs, however, none have yet been made which are as robust as a human. There has been much study on human inspired walking, such as AMBER lab which was established in 2008 by the Mechanical Engineering Department at Texas A&M University.[87] Many other robots have been built that walk on more than two legs, due to these robots being significantly easier to construct.[88][89] Walking robots can be used for uneven terrains, which would provide better mobility and energy efficiency than other locomotion methods. Typically, robots on two legs can walk well on flat floors and can occasionally walk up stairs. None can walk over rocky, uneven terrain. Some of the methods which have been tried are:

The zero moment point (ZMP) is the algorithm used by robots such as Honda's ASIMO. The robot's onboard computer tries to keep the total inertial forces (the combination of Earth's gravity and the acceleration and deceleration of walking), exactly opposed by the floor reaction force (the force of the floor pushing back on the robot's foot). In this way, the two forces cancel out, leaving no moment (force causing the robot to rotate and fall over).[90] However, this is not exactly how a human walks, and the difference is obvious to human observers, some of whom have pointed out that ASIMO walks as if it needs the lavatory.[91][92][93] ASIMO's walking algorithm is not static, and some dynamic balancing is used (see below). However, it still requires a smooth surface to walk on.

Several robots, built in the 1980s by Marc Raibert at the MIT Leg Laboratory, successfully demonstrated very dynamic walking. Initially, a robot with only one leg, and a very small foot could stay upright simply by hopping. The movement is the same as that of a person on a pogo stick. As the robot falls to one side, it would jump slightly in that direction, in order to catch itself.[94] Soon, the algorithm was generalised to two and four legs. A bipedal robot was demonstrated running and even performing somersaults.[95] A quadruped was also demonstrated which could trot, run, pace, and bound.[96] For a full list of these robots, see the MIT Leg Lab Robots page.[97]

A more advanced way for a robot to walk is by using a dynamic balancing algorithm, which is potentially more robust than the Zero Moment Point technique, as it constantly monitors the robot's motion, and places the feet in order to maintain stability.[98] This technique was recently demonstrated by Anybots' Dexter Robot,[99] which is so stable, it can even jump.[100] Another example is the TU Delft Flame.

Perhaps the most promising approach utilizes passive dynamics where the momentum of swinging limbs is used for greater efficiency. It has been shown that totally unpowered humanoid mechanisms can walk down a gentle slope, using only gravity to propel themselves. Using this technique, a robot need only supply a small amount of motor power to walk along a flat surface or a little more to walk up a hill. This technique promises to make walking robots at least ten times more efficient than ZMP walkers, like ASIMO.[101][102]

A modern passenger airliner is essentially a flying robot, with two humans to manage it. The autopilot can control the plane for each stage of the journey, including takeoff, normal flight, and even landing.[103] Other flying robots are uninhabited and are known as unmanned aerial vehicles (UAVs). They can be smaller and lighter without a human pilot on board, and fly into dangerous territory for military surveillance missions. Some can even fire on targets under command. UAVs are also being developed which can fire on targets automatically, without the need for a command from a human. Other flying robots include cruise missiles, the Entomopter, and the Epson micro helicopter robot. Robots such as the Air Penguin, Air Ray, and Air Jelly have lighter-than-air bodies, propelled by paddles, and guided by sonar.

Two robot snakes. Left one has 64 motors (with 2 degrees of freedom per segment), the right one 10.

Several snake robots have been successfully developed. Mimicking the way real snakes move, these robots can navigate very confined spaces, meaning they may one day be used to search for people trapped in collapsed buildings.[104] The Japanese ACM-R5 snake robot[105] can even navigate both on land and in water.[106]

A small number of skating robots have been developed, one of which is a multi-mode walking and skating device. It has four legs, with unpowered wheels, which can either step or roll.[107] Another robot, Plen, can use a miniature skateboard or roller-skates, and skate across a desktop.[108]

Capuchin, a climbing robot

Several different approaches have been used to develop robots that have the ability to climb vertical surfaces. One approach mimics the movements of a human climber on a wall with protrusions; adjusting the center of mass and moving each limb in turn to gain leverage. An example of this is Capuchin,[109] built by Dr. Ruixiang Zhang at Stanford University, California. Another approach uses the specialized toe pad method of wall-climbing geckoes, which can run on smooth surfaces such as vertical glass. Examples of this approach include Wallbot[110] and Stickybot.[111]

China's Technology Daily reported on 15 November 2008, that Dr. Li Hiu Yeung and his research group of New Concept Aircraft (Zhuhai) Co., Ltd. had successfully developed a bionic gecko robot named "Speedy Freelander". According to Dr. Yeung, the gecko robot could rapidly climb up and down a variety of building walls, navigate through ground and wall fissures, and walk upside-down on the ceiling. It was also able to adapt to the surfaces of smooth glass, rough, sticky or dusty walls as well as various types of metallic materials. It could also identify and circumvent obstacles automatically. Its flexibility and speed were comparable to a natural gecko. A third approach is to mimic the motion of a snake climbing a pole.[61]

It is calculated that when swimming some fish can achieve a propulsive efficiency greater than 90%.[112] Furthermore, they can accelerate and maneuver far better than any man-made boat or submarine, and produce less noise and water disturbance. Therefore, many researchers studying underwater robots would like to copy this type of locomotion.[113] Notable examples are the Essex University Computer Science Robotic Fish G9,[114] and the Robot Tuna built by the Institute of Field Robotics, to analyze and mathematically model thunniform motion.[115] The Aqua Penguin,[116] designed and built by Festo of Germany, copies the streamlined shape and propulsion by front "flippers" of penguins. Festo have also built the Aqua Ray and Aqua Jelly, which emulate the locomotion of manta ray, and jellyfish, respectively.

Robotic Fish: iSplash-II

In 2014 iSplash-II was developed by PhD student Richard James Clapham and Prof. Huosheng Hu at Essex University. It was the first robotic fish capable of outperforming real carangiform fish in terms of average maximum velocity (measured in body lengths/ second) and endurance, the duration that top speed is maintained.[117] This build attained swimming speeds of 11.6BL/s (i.e. 3.7 m/s).[118] The first build, iSplash-I (2014) was the first robotic platform to apply a full-body length carangiform swimming motion which was found to increase swimming speed by 27% over the traditional approach of a posterior confined waveform.[119]

The autonomous sailboat robot Vaimos

Sailboat robots have also been developed in order to make measurements at the surface of the ocean. A typical sailboat robot is Vaimos[120] built by IFREMER and ENSTA-Bretagne. Since the propulsion of sailboat robots uses the wind, the energy of the batteries is only used for the computer, for the communication and for the actuators (to tune the rudder and the sail). If the robot is equipped with solar panels, the robot could theoretically navigate forever. The two main competitions of sailboat robots are WRSC, which takes place every year in Europe, and Sailbot.

Radar, GPS, and lidar, are all combined to provide proper navigation and obstacle avoidance (vehicle developed for 2007 DARPA Urban Challenge)

Though a significant percentage of robots in commission today are either human controlled or operate in a static environment, there is an increasing interest in robots that can operate autonomously in a dynamic environment. These robots require some combination of navigation hardware and software in order to traverse their environment. In particular, unforeseen events (e.g. people and other obstacles that are not stationary) can cause problems or collisions. Some highly advanced robots such as ASIMO and Meinü robot have particularly good robot navigation hardware and software. Also, self-controlled cars, Ernst Dickmanns' driverless car, and the entries in the DARPA Grand Challenge, are capable of sensing the environment well and subsequently making navigational decisions based on this information, including by a swarm of autonomous robots.[35] Most of these robots employ a GPS navigation device with waypoints, along with radar, sometimes combined with other sensory data such as lidar, video cameras, and inertial guidance systems for better navigation between waypoints.

Kismet can produce a range of facial expressions.

The state of the art in sensory intelligence for robots will have to progress through several orders of magnitude if we want the robots working in our homes to go beyond vacuum-cleaning the floors. If robots are to work effectively in homes and other non-industrial environments, the way they are instructed to perform their jobs, and especially how they will be told to stop will be of critical importance. The people who interact with them may have little or no training in robotics, and so any interface will need to be extremely intuitive. Science fiction authors also typically assume that robots will eventually be capable of communicating with humans through speech, gestures, and facial expressions, rather than a command-line interface. Although speech would be the most natural way for the human to communicate, it is unnatural for the robot. It will probably be a long time before robots interact as naturally as the fictional C-3PO, or Data of Star Trek, Next Generation.

Interpreting the continuous flow of sounds coming from a human, in real time, is a difficult task for a computer, mostly because of the great variability of speech.[121] The same word, spoken by the same person may sound different depending on local acoustics, volume, the previous word, whether or not the speaker has a cold, etc.. It becomes even harder when the speaker has a different accent.[122] Nevertheless, great strides have been made in the field since Davis, Biddulph, and Balashek designed the first "voice input system" which recognized "ten digits spoken by a single user with 100% accuracy" in 1952.[123] Currently, the best systems can recognize continuous, natural speech, up to 160 words per minute, with an accuracy of 95%.[124] With the help of artificial intelligence, machines nowadays can use people's voice to identify their emotions such as satisfied or angry[125]

Other hurdles exist when allowing the robot to use voice for interacting with humans. For social reasons, synthetic voice proves suboptimal as a communication medium,[126] making it necessary to develop the emotional component of robotic voice through various techniques.[127][128] An advantage of diphonic branching is the emotion that the robot is programmed to project, can be carried on the voice tape, or phoneme, already pre-programmed onto the voice media. One of the earliest examples is a teaching robot named leachim developed in 1974 by Michael J. Freeman.[129][130] Leachim was able to convert digital memory to rudimentary verbal speech on pre-recorded computer discs.[131] It was programmed to teach students in The Bronx, New York.[131]

One can imagine, in the future, explaining to a robot chef how to make a pastry, or asking directions from a robot police officer. In both of these cases, making hand gestures would aid the verbal descriptions. In the first case, the robot would be recognizing gestures made by the human, and perhaps repeating them for confirmation. In the second case, the robot police officer would gesture to indicate "down the road, then turn right". It is likely that gestures will make up a part of the interaction between humans and robots.[132] A great many systems have been developed to recognize human hand gestures.[133]

Facial expressions can provide rapid feedback on the progress of a dialog between two humans, and soon may be able to do the same for humans and robots. Robotic faces have been constructed by Hanson Robotics using their elastic polymer called Frubber, allowing a large number of facial expressions due to the elasticity of the rubber facial coating and embedded subsurface motors (servos).[134] The coating and servos are built on a metal skull. A robot should know how to approach a human, judging by their facial expression and body language. Whether the person is happy, frightened, or crazy-looking affects the type of interaction expected of the robot. Likewise, robots like Kismet and the more recent addition, Nexi[135] can produce a range of facial expressions, allowing it to have meaningful social exchanges with humans.[136]

Artificial emotions can also be generated, composed of a sequence of facial expressions and/or gestures. As can be seen from the movie Final Fantasy: The Spirits Within, the programming of these artificial emotions is complex and requires a large amount of human observation. To simplify this programming in the movie, presets were created together with a special software program. This decreased the amount of time needed to make the film. These presets could possibly be transferred for use in real-life robots.

Many of the robots of science fiction have a personality, something which may or may not be desirable in the commercial robots of the future.[137] Nevertheless, researchers are trying to create robots which appear to have a personality:[138][139] i.e. they use sounds, facial expressions, and body language to try to convey an internal state, which may be joy, sadness, or fear. One commercial example is Pleo, a toy robot dinosaur, which can exhibit several apparent emotions.[140]

The Socially Intelligent Machines Lab of the Georgia Institute of Technology researches new concepts of guided teaching interaction with robots. The aim of the projects is a social robot that learns task and goals from human demonstrations without prior knowledge of high-level concepts. These new concepts are grounded from low-level continuous sensor data through unsupervised learning, and task goals are subsequently learned using a Bayesian approach. These concepts can be used to transfer knowledge to future tasks, resulting in faster learning of those tasks. The results are demonstrated by the robot Curi who can scoop some pasta from a pot onto a plate and serve the sauce on top.[141]

TOPIO, a humanoid robot, played ping pong at Tokyo IREX 2009.[142]

Control systems may also have varying levels of autonomy.

1. Direct interaction is used for haptic or teleoperated devices, and the human has nearly complete control over the robot's motion.
2. Operator-assist modes have the operator commanding medium-to-high-level tasks, with the robot automatically figuring out how to achieve them.[143]
3. An autonomous robot may go without human interaction for extended periods of time . Higher levels of autonomy do not necessarily require more complex cognitive capabilities. For example, robots in assembly plants are completely autonomous but operate in a fixed pattern.

Another classification takes into account the interaction between human control and the machine motions.

1. Teleoperation. A human controls each movement, each machine actuator change is specified by the operator.
2. Supervisory. A human specifies general moves or position changes and the machine decides specific movements of its actuators.
3. Task-level autonomy. The operator specifies only the task and the robot manages itself to complete it.
4. Full autonomy. The machine will create and complete all its tasks without human interaction.

External video
How the BB-8 Sphero Toy Works

The study of motion can be divided into kinematics and dynamics.[149] Direct kinematics or forward kinematics refers to the calculation of end effector position, orientation, velocity, and acceleration when the corresponding joint values are known. Inverse kinematics refers to the opposite case in which required joint values are calculated for given end effector values, as done in path planning. Some special aspects of kinematics include handling of redundancy (different possibilities of performing the same movement), collision avoidance, and singularity avoidance. Once all relevant positions, velocities, and accelerations have been calculated using kinematics, methods from the field of dynamics are used to study the effect of forces upon these movements. Direct dynamics refers to the calculation of accelerations in the robot once the applied forces are known. Direct dynamics is used in computer simulations of the robot. Inverse dynamics refers to the calculation of the actuator forces necessary to create a prescribed end-effector acceleration. This information can be used to improve the control algorithms of a robot.

In each area mentioned above, researchers strive to develop new concepts and strategies, improve existing ones, and improve the interaction between these areas. To do this, criteria for "optimal" performance and ways to optimize design, structure, and control of robots must be developed and implemented.

Bionics and biomimetics apply the physiology and methods of locomotion of animals to the design of robots. For example, the design of BionicKangaroo was based on the way kangaroos jump.

There has been some research into whether robotics algorithms can be run more quickly on quantum computers than they can be run on digital computers. This area has been referred to as quantum robotics.[150]

Universities like Worcester Polytechnic Institute (WPI) offer bachelors, masters, and doctoral degrees in the field of robotics.[153] Vocational schools offer robotics training aimed at careers in robotics.

The Robotics Certification Standards Alliance (RCSA) is an international robotics certification authority that confers various industry- and educational-related robotics certifications.

Several national summer camp programs include robotics as part of their core curriculum. In addition, youth summer robotics programs are frequently offered by celebrated museums and institutions.

There are many competitions around the globe. The SeaPerch curriculum is aimed as students of all ages. This is a short list of competition examples; for a more complete list see Robot competition.

The FIRST organization offers the FIRST Lego League Jr. competitions for younger children. This competition's goal is to offer younger children an opportunity to start learning about science and technology. Children in this competition build Lego models and have the option of using the Lego WeDo robotics kit.

One of the most important competitions is the FLL or FIRST Lego League. The idea of this specific competition is that kids start developing knowledge and getting into robotics while playing with Lego since they are nine years old. This competition is associated with National Instruments. Children use Lego Mindstorms to solve autonomous robotics challenges in this competition.

The FIRST Tech Challenge is designed for intermediate students, as a transition from the FIRST Lego League to the FIRST Robotics Competition.

The FIRST Robotics Competition focuses more on mechanical design, with a specific game being played each year. Robots are built specifically for that year's game. In match play, the robot moves autonomously during the first 15 seconds of the game (although certain years such as 2019's Deep Space change this rule), and is manually operated for the rest of the match.

The various RoboCup competitions include teams of teenagers and university students. These competitions focus on soccer competitions with different types of robots, dance competitions, and urban search and rescue competitions. All of the robots in these competitions must be autonomous. Some of these competitions focus on simulated robots.

AUVSI runs competitions for flying robots, robot boats, and underwater robots.

The Student AUV Competition Europe [154] (SAUC-E) mainly attracts undergraduate and graduate student teams. As in the AUVSI competitions, the robots must be fully autonomous while they are participating in the competition.

The Microtransat Challenge is a competition to sail a boat across the Atlantic Ocean.

RoboGames is open to anyone wishing to compete in their over 50 categories of robot competitions.

Federation of International Robot-soccer Association holds the FIRA World Cup competitions. There are flying robot competitions, robot soccer competitions, and other challenges, including weightlifting barbells made from dowels and CDs.

Many schools across the country are beginning to add robotics programs to their after school curriculum. Some major programs for afterschool robotics include FIRST Robotics Competition, Botball and B.E.S.T. Robotics.[155] Robotics competitions often include aspects of business and marketing as well as engineering and design.

The Lego company began a program for children to learn and get excited about robotics at a young age.[156]

Decolonial Educational Robotics is a branch of Decolonial Technology, and Decolonial A.I.,[157] practiced in various places around the world. This methodology is summarized in pedagogical theories and practices such as Pedagogy of the Oppressed and Montessori methods. And it aims at teaching robotics from the local culture, to pluralize and mix technological knowledge.[158]