N1 (rocket)

Static 3D model of the rocket

In May 1961, the US announced the goal of landing a person on the moon by 1970. During the same month, the On Reconsideration of the Plans for Space Vehicles in the Direction of Defense Purposes report set the first test launch of the N1 rocket for 1965. In June, Korolev was given a small amount of funding to start N1 development between 1961 and 1963. At the same time, Korolev proposed a lunar mission based on the new Soyuz spacecraft using an Earth orbit rendezvous profile. Several Soyuz rocket launches would be used to build up a complete Moon mission package, including one for the Soyuz spacecraft, another for the lunar lander, and a few with cislunar engines and fuel. This approach, driven by the limited capacity of the Soyuz rocket, meant that a rapid launch rate would be required to assemble the complex before any of the components ran out of consumables on-orbit. Korolev subsequently proposed that the N1 be enlarged to allow a single launch lunar landing.

Meanwhile, Chelomei's OKB-52 proposed an alternate mission with much lower risk. Instead of a crewed landing, Chelomei proposed a series of circumlunar missions to beat the US to the vicinity of the moon. He also proposed a new booster for the mission, clustering three of his existing UR-200s (known as the SS-10 in the west) to produce a single larger booster, the UR-500. These plans were dropped when Glushko offered Chelomei the RD-270, which allowed the construction of the UR-500 in a much simpler "monoblock" design. He also proposed adapting an existing spacecraft design for the circumlunar mission, the single-cosmonaut LK-1. Chelomei felt that improvements in early UR-500/LK-1 missions would allow the spacecraft to be adapted for two cosmonauts.

The Strategic Missile Forces of the Soviet military was reluctant to support a politically motivated project with little military utility, but both Korolev and Chelomei pushed for a lunar mission. Between 1961 and 1964, Chelomei's less aggressive proposal was accepted, and development of his UR-500 and the LK-1 were given a relatively high priority.

Valentin Glushko, who then held a near-monopoly on rocket engine design in the Soviet Union, proposed the RD-270 engine using unsymmetrical dimethylhydrazine (UDMH) and nitrogen tetroxide (N₂O₄) propellants to power the newly enlarged N1 design. These hypergolic propellants ignite on contact, reducing the complexity of the engine, and were widely used in Glushko's existing engines on various ICBMs. The full flow staged combustion cycle RD-270 was in testing before program cancellation, achieving a higher specific impulse than the gas-generator cycle Rocketdyne F-1 despite the use of UDMH/N₂O₄ propellants with lower potential impulse. The F-1 engine was five years into its development at the time and still experiencing combustion stability problems.

Glushko pointed out that the US Titan II GLV had successfully flown crew with similar hypergolic propellants. Korolev felt that the toxic nature of the fuels and their exhaust presented a safety risk for crewed space flight, and that kerosene/LOX was a better solution. The disagreement between Korolev and Glushko over the question of fuels ultimately became a major issue that hampered progress.[11][12]

Personal issues between the two played a role, with Korolev holding Glushko responsible for his incarceration at the Kolyma Gulag in the 1930s and Glushko considering Korolev to be cavalier and autocratic towards things outside his competence. The difference of opinions led to a falling out between Korolev and Glushko. In 1962, a committee was appointed to resolve the dispute and agreed with Korolev. Glushko refused outright to work on LOX/kerosene engines, and with Korolev in general. Korolev eventually gave up and decided to enlist the help of Nikolai Kuznetsov, the OKB-276 jet engine designer, while Glushko teamed up with other rocket designers to build the very successful Proton, Zenit, and Energia rockets.

Kuznetsov, who had limited experience in rocket design, responded with the NK-15, a fairly small engine that would be delivered in several versions tuned to different altitudes. To achieve the required amount of thrust, it was proposed that 30 NK-15s would be used in a clustered configuration. An outer ring of 24 engines and an inner ring of six engines would be separated by an air gap, with airflow supplied via inlets near the top of the booster. The air would be mixed with the exhaust in order to provide some degree of thrust augmentation, as well as engine cooling. The arrangement of 30 rocket engine nozzles on the N1's first stage could have been an attempt at creating a crude version of a toroidal aerospike engine system; more conventional aerospike engines were also studied.

N1 imaged by US KH-8 Gambit reconnaissance satellite, 19 September 1968

Korolev proposed a larger N1 combined with the new L3 lunar package based on the Soyuz 7K-L3. The L3 combined rocket stages, the modified Soyuz, and the new LK lunar lander were to be launched by a single N1 to conduct a lunar landing. Chelomei responded with a clustered UR-500-derived vehicle, topped with the L1 spacecraft already under development, and a lander developed by his design bureau. Korolev's proposal was selected as the winner in August 1964, but Chelomei was told to continue with his circumlunar UR-500/L1 work.

When Khrushchev was overthrown later in 1964, infighting between the two teams started anew. In October 1965, the Soviet government ordered a compromise; the circumlunar mission would be launched on Chelomei's UR-500 using Korolev's Soyuz spacecraft in place of their own Zond ("probe") design, aiming for a launch in 1967, the 50th anniversary of the Bolshevik Revolution. Korolev, meanwhile, would continue with his original N1-L3 proposal. Korolev had clearly won the argument, but work on the L1 continued anyway, as well as the Zond.

In 1966, the US Project Gemini had reversed the Soviet lead in human space exploration, Korolev initially lobbied for a crewed circumlunar mission, which was rejected. He was eventually successful on 3 August 1964 when the Central Committee finally passed a resolution titled "On work involving the study of the Moon and outer space" with the objective of landing a cosmonaut on the Moon in the 1967 to 68 time frame, ahead of the American Apollo missions.[13]

After Korolev died in 1966 due to complications after minor surgery, work on N1-L3 was taken over by his deputy, Vasily Mishin. Mishin did not have Korolev's political astuteness or influence and was reputed to be a heavy drinker. These problems contributed to the eventual cancellation of the N1 and the lunar mission as a whole, as did four consecutive launch failures with no successes.

• N1 1L – full scale dynamic test model, each stage was individually dynamically tested; the full N1 stack was only tested at 1/4 scale.[14]
• N1 2L (1M1) – Facilities Systems Logistic Test and Training Vehicle (FSLT & TV); two first stages painted gray, third stage gray-white and L3 white.[15]
• N1 3L – first launch attempt, engine fire, exploded at 12 km.
• N1 4L – Block A LOX tank developed cracks; never launched, parts from Block A used for other launchers; rest of airframe structure scrapped.[16]
• N1 5L – partially painted gray; first night launch; launch failure destroyed pad 110 East.
• N1 6L – launched from the second pad 110 West, deficient roll control, destroyed after 51s.
• N1 7L – all white, last launch attempt; engine cutoff at 40 kilometres (22 nmi) caused propellant line hammering, rupturing the fuel system.
• N1 8L and 9L – flight ready N1Fs with improved NK-33 engines in Block A, scrapped when the program was canceled.
• N1 10L – uncompleted, scrapped along with 8L and 9L.

Mishin continued with the N1F project after the cancellation of plans for a crewed Moon landing in the hope that the booster would be used to build the Zvezda moonbase. The program was terminated in 1974 when Mishin was replaced by Glushko. Two N1Fs were being readied for launch at the time, but these plans were canceled.

The two flight-ready N1Fs were scrapped and their remains could still be found around Baikonur years later used as shelters and storage sheds. The boosters were deliberately broken up in an effort to cover up the USSR's failed Moon attempts, which was publicly stated to be a paper project in order to fool the US into thinking there was a race going on. This cover story lasted until glasnost, when the remaining hardware was seen publicly on display.

The program was followed by the "Vulkan" concept for a huge launch vehicle using Syntin/LOX propellants, later replaced by LH2/LOX on the 2nd and 3rd stages. "Vulkan" was superseded by the Energia/Buran program in 1976.[17][18]

About 150 of the upgraded engines for the N1F escaped destruction. Although the rocket as a whole was unreliable, the NK-33 and NK-43 engines are rugged and reliable when used as a standalone unit. In the mid-1990s, Russia sold 36 engines for $1.1 million each and a license for the production of new engines to the US company Aerojet General.[19]

The US company Kistler Aerospace worked on incorporating these engines into a new rocket design with the intention of offering commercial launch services, but the attempt ended in bankruptcy. Aerojet also modified the NK-33 to incorporate thrust vector control capability for Orbital Science's Antares launch vehicle. Antares used two of these modified AJ-26 engines for first stage propulsion. The first four launches of the Antares were successful, but on the fifth launch the rocket exploded shortly after launch. Preliminary failure analysis by Orbital pointed to a possible turbopump failure in one NK-33/AJ-26. Given Aerojet's previous problems with the NK-33/AJ-26 engine during the modification and test program (two engine failures in static test firings, one of which caused major damage to the test stand) and the later in-flight failure, Orbital decided that the NK-33/AJ-26 was not reliable enough for future use.[20]

In Russia, N1 engines were not used again until 2004, when the remaining 70 or so engines were incorporated into a new rocket design, the Soyuz 3.[21][22] As of 2005, the project has been frozen due to the lack of funding. Instead, the NK-33 was incorporated into the first stage of a light variant of the Soyuz rocket, which was first launched on 28 December 2013.[23]

The first stage, Block A, was powered by 30 NK-15 engines arranged in two rings, the main ring of 24 at the outer edge of the booster and the core propulsion system consisting of the inner 6 engines at about half diameter.[26] The control system was primarily based on differential throttling of the engines of the outer ring for pitch and yaw. The core propulsion system was not used for control.[27] The Block A also included four grid fins, which were later used on Soviet air-to-air missile designs. In total, the Block A produced 45,400 kN (10,200,000 lbf) of thrust and could be regarded as a true Nova class first stage[28] (Nova was the name used by NASA to describe a very large booster in the 10-20 million pounds of thrust range).[29][30][31] This exceeded the 33,700 kN (7,600,000 lbf) thrust of the Saturn V.[32]

The KORD (Russian acronym for KOntrol Raketnykh Dvigateley—literally "Control (of) Rocket Engines"—Russian: Контроль ракетных двигателей)[33] was the automatic engine control system devised to throttle, shut down and monitor the large cluster of 30 engines in Block A (the first stage). The KORD system controlled the differential thrusting of the outer ring of 24 engines for pitch and yaw attitude control by throttling them appropriately and it also shut down malfunctioning engines situated opposite each other. This was to negate the pitch or yaw moment diametrically opposing engines in the outer ring would generate, thus maintaining symmetrical thrust. Block A could perform nominally with two pairs of opposing engines shut down (26/30 engines). Unfortunately the KORD system was unable to react to rapidly occurring processes such as the exploding turbo-pump during the second launch.[34] Due to the deficiencies of the KORD system, a new computer system was developed for the fourth and last launch. The S-530 was the first Soviet digital guidance and control system,[35] but unlike the KORD, which was essentially just an analogue engine control system, the S-530 supervised all control tasks in the launch vehicle and spacecraft, of which the N1 carried two, one located in the Block V third stage that controlled the engines for the first three stages. The second S-530 was located in the Soyuz LOK command module and provided control for the rest of the mission from TLI to lunar flyby and return to Earth.[36][37]

The second stage, Block B, was powered by 8 NK-15V engines arranged in a single ring. The only major difference between the NK-15 and -15V was the engine bell and various tunings for air-start and high-altitude performance. The N1F Block B replaced the NK-15 engines with upgraded NK-43 engines.

Block B could withstand the shutdown of one pair of opposing engines (6/8 engines).[34]

The upper stage, Block V (В/V being the third letter in the Russian alphabet), mounted four smaller NK-21 engines in a square. The N1F Block V replaced the NK-21 engines with NK-31 engines.

Block V could function with one engine shut down and three functioning correctly.[34]

The complex plumbing needed to feed fuel and oxidizer into the clustered arrangement of rocket engines was fragile and a major factor in 2 of the 4 launch failures. The N1's Baikonur launch complex could not be reached by heavy barge. To allow transport by rail, all of the stages had to be shipped in pieces and assembled at the launch site.

The NK-15 engines had a number of valves that were activated by pyrotechnics rather than hydraulic or mechanical means, this being a weight-saving measure. Once shut, the valves could not be re-opened.[38] This meant that the engines for Block A were only test-fired individually and the entire cluster of 30 engines was never static test fired as a unit. Sergei Khrushchev stated that only two out of every batch of six engines were tested, and not the units actually intended for use in the booster. As a result, the complex and destructive vibrational modes (which ripped apart propellant lines and turbines), as well as exhaust plume and fluid dynamic problems (causing vehicle roll, vacuum cavitation, and other problems), in Block A were not discovered and worked out before flight.[39] Blocks B and V were static test fired as complete units.

Because of its technical difficulties and lack of funding for a comprehensive test campaign, the N1 never completed a test flight. Twelve test flights were planned, with only four flown. All four uncrewed launches ended in failure before first-stage separation. The longest flight lasted 107 seconds, just before first-stage separation. Two test launches occurred in 1969, one in 1971, and the final one in 1972.

A comparison of the U.S. Saturn V rocket (left) with the Soviet N1/L3. Note: human at bottom illustrates scale

At 105 meters (344 ft), the N1-L3 was slightly shorter than the American Apollo-Saturn V (111 meters, 363 ft). The N-1 had a smaller overall diameter but a greater maximum diameter (17 m/56 ft vs. 10 m/33 ft). The N1 produced more thrust in each of its first three stages than the corresponding stages of the Saturn V. The N1-L3 produced more total impulse in its first four stages than the Saturn V did in its three (see table below).

The N1 was intended to place the approximately 95 t (209,000 lb) L3 payload into low Earth orbit,[40] with the fourth stage included in the L3 complex was intended to place 23.5 t (52,000 lb) into translunar orbit. In comparison, the Saturn V placed the roughly 45 t (100,000 lb) Apollo spacecraft plus about 74.4 t (164,100 lb) of fuel remaining in the S-IVB third stage for translunar injection into a similar Earth parking orbit.

The N1 used kerosene-based rocket fuel in all three of its main stages, while the Saturn V used liquid hydrogen to fuel its second and third stages, which yielded an overall performance advantage due to the higher specific impulse. The N1 also wasted available propellant volume by using spherical propellant tanks under a roughly conical external skin, while the Saturn V used most of its available cylindrical skin volume to house capsule-shaped hydrogen and oxygen tanks, with common bulkheads between the tanks in the second and third stages.

The N1-L3 would have been able to convert only 9.3% of its three-stage total impulse into Earth orbit payload momentum (compared to 12.14% for the Saturn V), and only 3.1% of its four-stage total impulse into translunar payload momentum, compared to 6.2% for the Saturn V.

Unlike Kennedy Space Center Launch Complex 39, the N1's Baikonur launch complex could not be reached by heavy barge. To allow transport by rail, all of the stages had to be shipped in pieces and assembled at the launch site. This led to difficulties in testing that contributed to the N1's lack of success.

The Saturn V also never lost a payload in two development and eleven operational launches, while four N1 development launch attempts all resulted in catastrophic failure, with two payload losses.

February 21, 1969: serial number 3L – Zond L1S-1 (Soyuz 7K-L1S (Zond-M) modification of Soyuz 7K-L1 "Zond" spacecraft) for Moon flyby

A few seconds into launch, a transient voltage caused the KORD to shut down Engine #12. After this happened, the KORD shut off Engine #24 to maintain symmetrical thrust. At T+6 seconds, pogo oscillation in the #2 engine tore several components off their mounts and started a propellant leak. At T+25 seconds, further vibrations ruptured a fuel line and caused RP-1 to spill into the aft section of the booster. When it came into contact with the leaking gas, a fire started. The fire then burned through wiring in the power supply, causing electrical arcing that was picked up by sensors and interpreted by the KORD as a pressurization problem in the turbopumps. The KORD responded by issuing a general command to shut down the entire first stage at T+68 seconds into launch. This signal was also transmitted up to the second and third stages, "locking" them and preventing a manual ground command from being sent to start their engines. Telemetry also showed that the power generators in the N-1 continued functioning until the impact with the ground at T+183 seconds. Investigators discovered the remains of the rocket 52 kilometers (32 miles) from the launch pad. Vasily Mishin had initially blamed the generators for the failure, as he could not think of any other reason why all 30 engines would shut down at once, but this was quickly disproven by telemetry data and the recovery of the generators from the crash site. They had survived in good condition and were shipped back to the Istra plant, where they were refurbished and worked without any problems under bench testing. The investigative team did not speculate as to whether the burning first stage could have continued flying if the KORD system had not shut it down. The KORD was found to have a number of serious design flaws and poorly programmed logic. One unforeseen flaw was that its operating frequency, 1000 Hz, happened to perfectly coincide with vibration generated by the propulsion system, and the shutdown of Engine #12 at liftoff was believed to have been caused by pyrotechnic devices opening a valve, which produced a high-frequency oscillation that went into adjacent wiring and was assumed by the KORD to be an overspeed condition in the engine's turbopump. The wiring in Engine #12 was believed to be particularly vulnerable to this effect due to its length; however, other engines had similar wiring and were unaffected. Also, the system's operating voltage increased to 25V instead of the nominal 15V. The control wiring was relocated and coated with asbestos for fireproofing and the operating frequency changed.[42][43] The launch escape system was activated and did its job properly, saving the mockup of the spacecraft. All subsequent flights had freon fire extinguishers installed next to every engine.[44][45] According to Sergei Afanasiev, the logic of the command to shut down the entire cluster of 30 engines in Block A was incorrect in that instance, as the subsequent investigation revealed.[46][47]

Serial number 5L – Zond L1S-2 for Moon orbit and flyby and intended photography of possible crewed landing sites.

The second N-1 vehicle was launched on 3 July 1969 and carried a modified L1 Zond spacecraft and live escape tower. Boris Chertok claimed that a mass model lunar module was also carried; however, most sources indicate that only the L1S-2 and boost stages were on board N-1 5L. Launch took place at 11:18 PM Moscow time. For a few moments, the rocket lifted into the night sky. As soon as it cleared the tower, there was a flash of light, and debris could be seen falling from the bottom of the first stage. All the engines instantly shut down except engine #18. This caused the N-1 to lean over at a 45-degree angle and drop back onto launch pad 110 East.[48] The nearly 2300 tons of propellant on board triggered a massive blast and shock wave that shattered windows across the launch complex and sent debris flying as far as 10 kilometers (6 miles) from the center of the explosion. Launch crews were permitted outside half an hour after the accident and encountered droplets of unburned fuel still raining down from the sky. The majority of the N-1's propellant load had not been consumed in the accident, and most of what had burned was in the first stage of the rocket. However, the worst-case scenario, mixing of the fuel and LOX to form an explosive gel, had not occurred. The subsequent investigation revealed that up to 85% of the propellant on board the rocket did not detonate, reducing the force of the blast.[49] The launch escape system had activated at the moment of engine shutdown (T+15 seconds) and pulled the L1S-2 capsule to safety kilometers (1.2 miles) away. Impact with the pad occurred at T+23 seconds. Launch Complex 110 East was thoroughly leveled by the blast, with the concrete pad caved in and one of the lighting towers knocked over and twisted around itself. Despite the devastation, most of the telemetry tapes were found intact in the debris field and examined.

Just before liftoff, the LOX turbopump in the #8 engine exploded (the pump was recovered from the debris and found to have signs of fire and melting). The resultant shock wave severed surrounding propellant lines and started a fire from leaking fuel. The fire damaged various components in the thrust section[50] leading to the engines gradually being shut down between T+10 and T+12 seconds. The KORD had shut off engines #7, #19, #20, and #21 after detecting abnormal pressure and pump speeds. Telemetry did not provide any explanation as to what shut off the other engines. Engine #18, which had caused the booster to lean over 45 degrees, continued operating until impact, something engineers were never able to satisfactorily explain. It could not be determined exactly why the #8 turbopump had exploded. Working theories were that either a piece of a pressure sensor had broken off and lodged in the pump, or that its impeller blades had rubbed against the metal casing, creating a friction spark that ignited the LOX. The #8 engine had operated erratically prior to shutdown and a pressure sensor detected "incredible force" in the pump. Vasily Mishin believed that a pump rotor had disintegrated, but Kuznetsov argued that the NK-15 engines were entirely blameless and Mishin, who had defended the use of Kuznetsov's engines two years earlier, could not publicly come out and challenge him. Kuznetsov succeeded in getting the postflight investigative committee to rule the cause of the engine failure as "ingestion of foreign debris". Vladimir Barmin, chief director of launch facilities at Baikonur, also argued that the KORD should be locked for the first 15–20 seconds of flight to prevent a shutdown command from being issued until the booster had cleared the pad area.[51][52] The destroyed complex was photographed by American satellites, disclosing that the Soviet Union was building a Moon rocket.[45] After this flight, fuel filters were installed in later models.[45] It also took 18 months to rebuild the launch pad and delayed launches. This was one of the largest artificial non-nuclear explosions in human history and was visible that evening 35 kilometres (22 miles) away at Leninsk (See Tyuratam).[53]

June 26, 1971: serial number 6L – dummy Soyuz 7K-LOK (Soyuz 7K-L1E No.1) and dummy LK module-spacecraft

Soon after lift-off, due to unexpected eddies and counter-currents at the base of Block A (the first stage), the N-1 experienced an uncontrolled roll beyond the capability of the control system to compensate. The KORD computer sensed an abnormal situation and sent a shutdown command to the first stage, but as noted above, the guidance program had since been modified to prevent this from happening until 50 seconds into launch. The roll, which had initially been 6° per second, began rapidly accelerating. At T+39 seconds, the booster was rolling at nearly 40° per second, causing the inertial guidance system to go into gimbal lock and at T+48 seconds, the vehicle disintegrated from structural loads. The interstage truss between the second and third stages twisted apart and the latter separated from the stack and at T+50 seconds, the cutoff command to the first stage was unblocked and the engines immediately shut down. The upper stages impacted about 7 kilometers (4 miles) from the launch complex. Despite the engine shutoff, the first and second stages still had enough momentum to travel for some distance before falling to earth about 15 kilometers (9 miles) from the launch complex and blasting a 15-meter-deep (50-foot) crater in the steppe.[54] This N1 had dummy upper stages without the rescue system. The next, last vehicle would have a much more powerful stabilization system with dedicated engines (in the previous versions stabilization was done by directing exhaust from the main engines). The engine control system would also be reworked, increasing the number of sensors from 700 to 13,000.[45][55]

November 23, 1972: serial number 7L – regular Soyuz 7K-LOK (Soyuz 7K-LOK No.1) and dummy LK module-spacecraft for Moon flyby

The start and lift-off went well. At T+90 seconds, a programmed shutdown of the core propulsion system (the six center engines) was performed to reduce structural stress on the booster. Because of excessive dynamic loads caused by a hydraulic shock wave when the six engines were shut down abruptly, lines for feeding fuel and oxidizer to the core propulsion system burst and a fire started in the boattail of the booster; in addition, the #4 engine exploded. The first stage broke up starting at T+107 seconds and all telemetry data ceased at T+110 seconds. The launch escape system activated and pulled the Soyuz 7K-LOK to safety. The upper stages were ejected from the stack and crashed into the steppe. An investigation revealed that the abrupt shutdown of the engines led to fluctuations in the fluid columns of the feeder pipes, which ruptured and spilled fuel and oxidizer onto the shut down, but still hot, engines. A failure of the #4 engine turbopump was also suspected. It was believed that the launch could have been salvaged had ground controllers sent a manual command to jettison the first stage and begin second stage burn early as the stage failed only 15 seconds before it was due to separate at T+125 seconds and it had reached the nominal burn time of 110 seconds according to the cyclogram.[56][57][58]

Vehicle serial number 8L was prepared for August 1974. It included a regular 7K-LOK Soyuz 7K-LOK and a regular LK module-spacecraft of the L3 lunar expedition complex. It was intended for a Moon flyby and uncrewed landing in preparation for a future crewed mission. As the N1-L3 program was canceled in May 1974, this launch never took place.[59][60]