Hayabusa2

Animation of Hayabusa2 orbit from 3 December 2014
  Hayabusa2   162173 Ryugu   Earth   Sun

Asteroid 162173 Ryugu (formerly designated 1999 JU₃) is a primitive carbonaceous near-Earth asteroid. Carbonaceous asteroids are thought to preserve the most pristine, untainted materials in the Solar System, a mixture of minerals, ice, and organic compounds that interact with each other.[14] Studying it is expected to provide additional knowledge on the origin and evolution of the inner planets and, in particular, the origin of water and organic compounds on Earth,[14][15] all relevant to the origin of life on Earth.[16]

Initially, launch was planned for 30 November 2014,[17][18][19] but was delayed to 3 December 2014 at 04:22:04 UTC (3 December 2014, 13:22:04 local time) on a H-IIA launch vehicle.[20] Hayabusa2 launched together with PROCYON asteroid flyby space probe. PROCYON's mission was a failure. Hayabusa2 arrived at Ryugu on 27 June 2018,[10] where it surveyed the asteroid for a year and a half and collected samples.[14] It departed the asteroid in November 2019 and returned the samples to Earth in December 2020.[19]

Compared to the previous Hayabusa mission, the spacecraft features improved ion engines, guidance and navigation technology, antennas, and attitude control systems.[21] A kinetic penetrator (i.e., bullet) was shot into the asteroid surface to expose pristine sample material which was later collected for return to Earth.[15][19]

Following the initial success of Hayabusa, JAXA began studying a potential successor mission in 2007.[22] In July 2009, Makoto Yoshikawa of JAXA presented a proposal titled "Hayabusa Follow-on Asteroid Sample Return Missions". In August 2010, JAXA obtained approval from the Japanese government to begin development of Hayabusa2. The cost of the project estimated in 2010 was 16.4 billion yen (US$150 million).[9][23]

Hayabusa2 was launched on 3 December 2014, arrived at asteroid Ryugu on 27 June 2018, and remained stationary at a distance of about 20 km (12 mi) to study and map the asteroid. In the week of 16 July 2018, commands were sent to move to a lower hovering altitude.[24]

On 21 September 2018, the Hayabusa2 spacecraft ejected the first two rovers, Rover-1A (HIBOU)[25] and Rover-1B (OWL), from about a 55 m (180 ft) altitude that dropped independently to the surface of the asteroid.[26][27] They functioned nominally and transmitted data.[28] The MASCOT rover deployed successfully on 3 October 2018 and operated for about 16 hours as planned.[29]

The first sample collection was scheduled to start in late October 2018, but the rovers encountered a landscape with large and small boulders but no surface soil for sampling. Therefore, it was decided to postpone the sample collection plans to 2019 and further evaluate various options for the landing.[30][31] The first surface sample retrieval took place on 21 February 2019. On 5 April 2019, Hayabusa2 released an impactor to create an artificial crater on the asteroid surface. However, Hayabusa2 initially failed on 14 May 2019 to drop special reflective markers necessary onto the surface for guiding the descent and sampling processes,[32] but later it successfully dropped one from an altitude of 9 m (30 ft) on 4 June 2019.[33] The sub-surface sampling took place on 11 July 2019.[34] The spacecraft departed the asteroid on 13 November 2019 (with departure command sent at 01:05 UTC on 13 November 2019). It successfully delivered the samples back to Earth on 6 December 2020 (Japan Standard Time|JST), dropping the contents by parachute in a special container at a location in southern Australia. The samples were retrieved the same day for secure transport back to the JAXA labs in Japan.[7][35][36]

The design of Hayabusa2 is based on the first Hayabusa spacecraft, with some improvements.[14][39] It has a mass of 610 kilograms (1,340 lb) including fuel,[39] and electric power is generated by two sets of solar arrays with an output of 2.6 kW at 1 AU, and 1.4 kW at 1.4 AU.[39] The power is stored in eleven inline-mounted 13.2 Ah lithium-ion batteries.[39]

Propulsion

The spacecraft features four solar-electric ion thrusters for propulsion called μ10,[37] one of which is a backup. These engines use microwaves to convert xenon into plasma (ions), which are accelerated by applying a voltage from the solar panels and ejected out the back of the engine. The simultaneous operation of three engines generates thrusts of up to 28 mN.[39] Although this thrust is very small, the engines are also extremely efficient; the 66 kg (146 lb) of xenon[37] reaction mass can change the speed of the spacecraft by up to 2 km/s.[39]

The spacecraft has four redundant reaction wheels and a chemical reaction control system featuring twelve thrusters for attitude control (orientation) and orbital control at the asteroid.[37][39] The chemical thrusters use hydrazine and MON-3, with a total mass of 48 kg (106 lb) of chemical propellant.[39]

Communication

The primary contractor NEC built the 590 kg (1,300 lb) spacecraft, its Ka-band communications system and a mid-infrared camera.[40] The spacecraft has two high-gain directional antennas for X-band and K_a-band.[37] Bit rates are 8 bit/s to 32 kbit/s.[39] The ground stations are the Usuda Deep Space Center, Uchinoura Space Center, NASA Deep Space Network and Malargüe Station (ESA).[39]

Navigation

The optical navigation camera telescope (ONC-T) is a telescopic framing camera with seven colors to optically navigate the spacecraft.[41] It works in synergy with the optical navigation camera wide-field (ONC-W2) and with two star trackers.[39]

In order to descend to the asteroid surface to perform sampling, the spacecraft released one of five target markers in the selected landing zones as artificial guide marks, with highly reflective outer material that is recognized by a strobe light mounted on the spacecraft.[39] The spacecraft also used its laser altimeter and ranging (LIDAR) as well as Ground Control Point Navigation (GCP-NAV) sensors during sampling.[39]

Hayabusa2 instrument inventory

The Hayabusa2 payload is equipped with multiple scientific instruments:[39][42]

• Remote sensing: Optical Navigation Camera (ONC-T, ONC-W1, ONC-W2), Near-Infrared Camera (NIR3), Thermal-Infrared Camera (TIR), Light Detection And Ranging (LIDAR)
• Sampling: Sampling device (SMP), Small Carry-on Impactor (SCI), Deployable Camera (DCAM3)
• Four rovers: Mobile Asteroid Surface Scout (MASCOT), Rover-1A, Rover-1B, Rover-2.

Hayabusa2 carried four small rovers to explore the asteroid surface in situ,[45] and provide context information for the returned samples. Due to the minimal gravity of the asteroid, all four rovers were designed to move around by short hops instead of using normal wheels. They were deployed at different dates from about 60 m (200 ft) altitude and fell freely to the surface under the asteroid's weak gravity.[46] The first two rovers, called HIBOU (previously Rover-1A) and OWL (previously Rover-1B), landed on asteroid Ryugu on 21 September 2018.[28] The third rover, called MASCOT, was deployed 3 October 2018. Its mission was successful.[47] The fourth rover, known as Rover-2 or MINERVA-II-2, failed before release from the orbiter. It was released on 2 October 2019 to orbit the asteroid and perform gravitational measurements before being allowed to impact the asteroid a few days later.

MINERVA-II

Main article: MINERVA-II

The first photograph from the surface of an asteroid, taken by HIBOU on 22 September 2018 during one of its "hops".

MINERVA-II is a successor to the MINERVA lander carried by Hayabusa. It consists of two containers with 3 rovers.

MINERVA-II-1 is a container that deployed two rovers, Rover-1A (HIBOU) and Rover-1B (OWL), on 21 September 2018.[48][49] It was developed by JAXA and the University of Aizu. The rovers are identical having a cylindrical shape, 18 cm (7.1 in) diameter and 7 cm (2.8 in) tall, and a mass of 1.1 kg (2.4 lb) each.[39][50] They move by hopping in the low gravitational field, using a torque generated by rotating masses within the rovers.[51] Their scientific payload is a stereo camera, wide-angle camera, and thermometers. Solar cells and double-layer capacitors provide the electrical power.[52][53] The MINERVA-II-1 rovers were successfully deployed 21 September 2018. Both rovers performed successfully on the asteroid surface, sending images and video from the surface. Rover-1A operated for 113 asteroid days (36 Earth days) returning 609 images from the surface, and Rover-1B operated for 10 asteroid days (3 Earth days) returning 39 images from the surface.[54]

The MINERVA-II-2 container held the ROVER-2 (sometimes referred to as MINERVA-II-2), developed by a consortium of universities led by Tohoku University in Japan. This was an octagonal prism shape, 15 cm (5.9 in) diameter and 16 cm (6.3 in) tall, with a mass of about 1 kg (2.2 lb). It had two cameras, a thermometer and an accelerometer. It was equipped with optical and ultraviolet LEDs to illuminate and detect floating dust particles. ROVER-2 carried four mechanisms to move around using short hops.[52] Rover-2 had problems prior to deployment from the orbiter but was released on 2 October 2019 to orbit the asteroid and perform gravitational measurements. It was then crashed onto the asteroid surface a few days later on 8 October 2019.

MASCOT

"MASCOT" redirects here. For other uses, see Mascot (disambiguation).

MASCOT lander attached to the side of Hayabusa2.

The Mobile Asteroid Surface Scout (MASCOT) was developed by the German Aerospace Center (DLR) in cooperation with the French space agency CNES.[55] It measures 29.5 cm × 27.5 cm × 19.5 cm (11.6 in × 10.8 in × 7.7 in) and has a mass of 9.6 kg (21 lb).[56] MASCOT carries four instruments: an infrared spectrometer (MicrOmega), a magnetometer (MASMAG), a radiometer (MARA), and a camera (MASCAM) that imaged the small-scale structure, distribution and texture of the regolith.[57] The rover is capable of tumbling once to reposition itself for further measurements.[45][58] It collected data on the surface structure and mineralogical composition, the thermal behaviour and the magnetic properties of the asteroid.[59] It has a non-rechargeable battery that allowed for operations for approximately 16 hours.[60][61] The infrared radiometer on the InSight Mars lander, launched in 2018, is based on the MASCOT radiometer.[62][63]

MASCOT was deployed 3 October 2018. It had a successful landing and performed its surface mission successfully. Two papers were published describing the results from MASCOT in the scientific journals Nature Astronomy and Science. One finding of the research was that C-type asteroids consist of more porous material than previously thought, explaining a deficit of this meteorite type. Meteorites of this type are too porous to survive the entry into the atmosphere of planet Earth. Another finding was that Ryugu consists of two different almost black types of rock with little internal cohesion, but no dust was detected.[64][65] A third paper describing results from MASCOT was published in the Journal of Geophysical Research and describes the magnetic properties of Ryugu, showing that Ryugu does not have a magnetic field on a boulder scale.[66]

Artistic rendering of Hayabusa collecting a surface sample.

The original plan was for the spacecraft to collect up to three samples: 1) surface material that exhibits traits of hydrous minerals; 2) surface material with either unobservable or weak evidence of aqueous alterations; 3) excavated sub-surface material.[71]

The first two surface samples were scheduled to start in late October 2018, but the rovers showed large and small boulders and insufficient surface area to sample, so the mission team decided to postpone sampling to 2019 and evaluate various available options.[30] The first surface sampling was completed on 22 February 2019 and obtained a substantial amount of topsoil,[70][72] so the second surface sampling was postponed and was eventually cancelled to decrease the risks to the mission.[70]

The second and final sample was collected from material that was dislodged from beneath the surface by the kinetic impactor (SCI impactor) shot from a distance of 300 m (980 ft).[73][74] All samples are stored in separate sealed containers inside the sample return capsule (SRC).

Sub-surface sample

Animation illustrating SCI deployment and subsequent sampling from the resulting crater.

The sub-surface sample collection required an impactor to create a crater in order to retrieve material under the surface, not subjected to space weathering. This required removing a large volume of surface material with a powerful impactor. For this purpose, Hayabusa2 deployed on 5 April 2019 a free-flying gun with one "bullet", called the Small Carry-on Impactor (SCI); the system contained a 2.5 kg (5.5 lb) copper projectile, shot onto the surface with an explosive propellant charge. Following SCI deployment, Hayabusa2 also left behind a deployable camera (DCAM3)[Note 1] to observe and map the precise location of the SCI impact, while the orbiter maneuvered to the far side of the asteroid to avoid being hit by debris from the impact.

Approximately 40 minutes after separation, when the spacecraft was at a safe distance, the impactor was fired into the asteroid surface by detonating a 4.5 kg (9.9 lb) shaped charge of plasticized HMX for acceleration.[58][76] The copper impactor was shot onto the surface from an altitude of about 500 m (1,600 ft) and it excavated a crater of about 10 m (33 ft) in diameter, exposing pristine material.[15][32] The next step was the deployment on 4 June 2019 of a reflective target marker in the area near the crater to assist with navigation and descent.[33] The touchdown and sampling took place on 11 July 2019.[34]

Replica of Hayabusa's sample-return capsule (SRC) used for re-entry. Hayabusa2's capsule is of the same size, measuring 40 cm (16 in) in diameter and using a parachute for touchdown.

The spacecraft collected and stored the samples in separate sealed containers inside the sample-return capsule (SRC), which is equipped with thermal insulation. The container is 40 cm (16 in) external diameter, 20 cm (7.9 in) in height, and a mass of about 16 kg (35 lb).[39]

At the end of the science phase in November 2019,[7] Hayabusa2 used its ion engines for changing orbit and return to Earth.[75] Hours before Hayabusa2 flew past Earth in late 2020, it released the capsule, on 5 December 2020 at 05:30 UTC.[77] The capsule was released spinning at one revolution per three seconds. The capsule re-entered the Earth's atmosphere at 12 km/s (7.5 mi/s) and it deployed a radar-reflective parachute at an altitude of about 10 km (6.2 mi), and ejected its heat-shield, while transmitting a position beacon signal.[39][75] The sample capsule landed at the Woomera Test Range in Australia.[13][78] The total flight distance was 5.24×10^⁹ km (35.0 AU).[39]

Any volatile substances will be collected before the sealed containers are opened.[71] The samples will be curated and analyzed at JAXA's Extraterrestrial Sample Curation Center,[79] where international scientists can request a small portion of the samples. The spacecraft brought back a capsule containing carbon-rich asteroid fragments that scientists believe could provide clues about the ancient delivery of water and organic molecules to Earth.[80][81]

With the successful return and retrieval of the sample capsule on 6 December 2020 (JST), Hayabusa2 will now use its remaining 30 kg (66 lb) of xenon propellant (from the initial 66 kg (146 lb)) to extend its service life and fly out to explore new targets.[82] As of September 2020, a fly-by of (98943) 2001 CC21[83] in July 2026 and a rendezvous with 1998 KY26 in July 2031 were selected for the mission extension.[84][85][86] The observation of 2001 CC₂₁ will be during a high-speed fly-by of an L-type asteroid, a relatively uncommon type of asteroid.[87] The fixed camera of Hayabusa2 was not designed for this type of fly-by. The rendezvous with 1998 KY₂₆ will be the first visit of a fast rotating micro-asteroid, with a rotation period of about 10 minutes.[86] Between 2021 and 2026, the spacecraft will also conduct observations of exoplanets.[88] An option to conduct a Venus flyby to set up an encounter with 2001 AV43 was also studied.[89][90]

Selected EAEEA (Earth → Asteroid → Earth → Earth → Asteroid) scenario:[86]

• December 2020: Extension mission start
• 2021 until July 2026: cruise operation
• July 2026: L-type asteroid 2001 CC₂₁ high-speed fly-by
• December 2027: Earth swing-by
• June 2028: Second Earth swing-by
• July 2031: Target body (1998 KY₂₆) rendezvous

• Abiogenesis
• Hayabusa Mk2
• OSIRIS-REx – NASA asteroid sample return mission to 101955 Bennu (operational at the same time as Hayabusa2)
• Panspermia
• 162173 Ryugu

Wikimedia Commons has media related to Hayabusa2.

• Hayabusa2 project website
• JAXA Hayabusa2 website
• Hayabusa2 Science Data Archives hosted by the DARTS archive (ISAS)
• MASCOT related publications by the Institute of Planetary Research hosted by Europlanet
• Hayabusa2 images scientific commentary, University of Tokyo
• Asteroid Explorer Hayabusa2, NEC
• Hayabusa2 3D model, Asahi Shinbun